Philips Dynalite DDNG100BT Manuel utilisateur

features

Single Phase supply –230 +/- 14% 50/60Hz 0.1A

1 x RS485 Port –Dynet lighting control.

1 x 10/100BaseT - Ethernet port

Powerful Internal PLC - Custom scripts can be written

to provide process control based on conditional logic.

DIN Rail Mounting - 12 Units wide.

Warning –This is a class A product. In a domestic environment this product

may cause radio interference in which case the user may be required to take

adequate measures.

Read Instructions –We recommend that you read this Instruction Manual prior

to commencement of installation.

Special Programming –This device will only operate in basic modes unless

programmed via a computer. If programming is required, contact your local

agent for details. Once the data cable is connected to the devices, the factory

default settings will allow any control panel to operate all channels in all

controllers.

Mounting Location –Install in a dry, well-ventilated location.

Data Cable –Use screened, stranded RS485 data cable with three twisted

pairs. Segregate from mains cables by 300mm. Connect devices in a ‘daisy

chain’. Do not cut or terminate live data cables.

Power Sources –This device should only be operated from the type of supply

specified on the front panel. This device must be earthed.

Megger Testing –Do not megger test any circuitry connected to the control

system, as damage to the electronics may result.

DDNG100BT

10/100BaseT Ethernet

Installation Manual

Warning

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS DEVICE TO RAIN OR MOISTURE.

DO NOT ENERGISE UNLESS THE FRONT COVER IS IN PLACE.

THIS DEVICE MUST BE EARTHED.

INSTALLATION, PROGRAMMING AND MAINTENANCE MUST BE

CARRIED OUT BY QUALIFIED PERSONNEL.

Electrical diagram

connecting data cable

product specifications

Supply: 230 +/- 14% 50/60Hz Single Phase

Serial Port 1: 1 x 10/100BaseT Ethernet, consisting of 1 x RJ45 socket

Serial Port 2: 1 x RS485 unterminated, consisting of 1 x RJ12 socket & 1 x 5 way terminal block

RS485 Data Formats: DyNet, DyNet II

User Controls: Service Switch, Diagnostic LED

Internal Controls: Programmable Logic Controller, 64 Tasks

Operating Environment: 0º to 50ºC ambient temperature, 0% to 95% RH non condensing

Power Consumption: 450mA from the DyNet network at 12VDC

Compliance: CE, C-Tick

Construction: Polycarbonate DIN Rail enclosure (12 unit)

Dimensions: H 93mm x W 211mm x D 75mm

Weight: 0.86kg

DDNG100BT Installation Manual Rev B.doc Specifications subject to change without notice

Philips Dynalite manufactured by WMGD Pty Ltd (ABN 33 097 246 921) Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia Tel: +61 2 8338 9899 Fax: +61 2 8338 9333

E-Mail: dynalite.info@philips.com Web: Philips.com/dynalite

1. Mount the device on a DIN rail inside an appropriate enclosure

2. Connect supply cables feed from the appropriately rated protection.

3. Connect Ethernet and Dynet data cables to the device as per label on device.

4. Power up device once all termination have been re checked.

5. The unit will need to be configured using Envision commissioning tool

Installation steps

Table des matières

Autres manuels Philips Porte

Philips

Philips Dynalite DDNG232 Manuel utilisateur

Philips

Philips Dynalite DDMIDC8 Manuel utilisateur

Philips

Philips Dynalite DDNG485 Manuel utilisateur

Philips

Philips Dynalite DDNI485 Manuel utilisateur

Philips

Philips Dynalite DDNG-KNX Manuel utilisateur

Philips

Philips Dynalite PDZG-E Manuel utilisateur

Philips

Philips Dynalite DMNG232 Manuel utilisateur

Philips

Philips Dynalite DDNG485 Manuel utilisateur

Philips

Philips CPWBS054/05 Manuel utilisateur

Philips

Philips CPWBS054/05 Manuel utilisateur

Philips

Philips Dynalite DDNI-LON Manuel utilisateur

Philips

Philips Dynalite DTK622-USB Manuel utilisateur

Philips

Philips PDEG Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur