Philips CMP100/93 Manuel utilisateur

www.philips.com/welcome

CMP100

EN User manual

1. Important

Safety

•

Read and understand all instructions before you use the apparatus.

If damage is caused by failure to follow instructions, the warranty does

not apply.

This unit is designed for negative ground (earth) 12 V DC operation only.•

Use only the supplied mounting hardware for a safe and secure•

installation.

Do not connect any active speakers (with built-in amplier) to the •

speaker terminals of the unit. Doing so may damage the active speakers.

To ensure safe driving, adjust the volume to a safe and comfortable level.•

To avoid short circuit, do not expose the apparatus to rain or water.•Never expose the apparatus to direct sunlight, naked ames or heat.•

Clean the apparatus with soft, damp cloth. Never use substances such as•

alcohol, chemicals or household cleaners on the apparatus.

Notice

Environmental information

All unnecessary packaging has been omitted. We have tried to make

the packaging easy to separate into three materials: cardboard (box),

polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.)

Your system consists of materials which can be recycled and reused if

disassembled by a specialized company. Please observe the local regulations

regarding the disposal of packaging materials, exhausted batteries and old

equipment.

Any changes or modications made to this device that are not expressly

approved by Philips Consumer Lifestyle may void the user’s authority to

operate the equipment.

Specications are subject to change without notice. Trademarks are the property of Koninklijke

Philips Electronics N.V. or their respective owners. Philips reserves the right to change products at

any time without being obliged to adjust earlier supplies accordingly.

Your car power amplier

Congratulations on your purchase, and welcome to Philips!To fully

benet from the support that Philips offers, register your product at

www.philips.com/welcome.

Introduction

With the amplier, you can enjoy high quality sound performance with

powerful bass and beats.

What’s in the box

Check and identify the contents of your package:

a Amplier

bScrew_4x14mm (x4)

cFuse (x2)

dHi input connector (x1)

Overview of the main unit

dhi

320Hz

30Hz

SUB

WOOFER

SUBSONIC

ON OFF

REMOTE

LEVEL CONTROL

feg

dhi

320Hz

30Hz

SUB

WOOFER

SUBSONIC

ON OFF

REMOTE

LEVEL CONTROL

feg

aINPUT L/R

• Connect car audio with RCA cable.

bHI INPUT

Connect car audio with the supplied high input connector.

•

cINPUT LEVEL

Adjust input level (0.3V to 6V).

•

dBASS BOOST

Boost the frequencies at around 40Hz to a maximum of

•

12dB.

eSUBWOOFER

Adjust frequency of subwoofer from 30Hz to 320Hz.

•

fPROTECT

Light in red when the PROTECTOR is activated.

•

gPOWER

Light in blue when power is turned on.

•

hSUB SONIC ON/OFF

Switch on or off the subsonic lter.

•

iREMOTE LEVER CONTROL

External remote

• controller for volume level control.

jPOWER (GND/REM/+12V)

Connect +12V DC power cable, ground wire and remote

•

wire.

kFuse

lSPEAKER OUTPUT

Connect to subwoofers.

•

2. Installation

Installation

You can mount the amplier either under a seat or on the rear tray.

Note

To avoid interference, do not place the amplier too close to the car audio or

•

antenna.

The supplied mounting screws are 14mm long. Make sure that the mounting

•

board is thicker than 14mm.

1Place the unit on the location for installation.

2Mark the positions of the four screw holes.

3Drill the holes with driller of approximately

3mm in diameter.

4Mount the unit with the supplied screws.

Connect speakers

Note

Use speakers with an impedance of 2 to 8 ohm (4 to 8 ohm when used as a

•

bridged amplier).

Match the “left”, “right”, “+” and “-” terminals correctly. Revised polarity may

•

degrade sound quality.

Option 1: Mono bridged mode: connect 1 speaker

4 ohm speaker

Option 2: Stereo mode: connect 2 speakers

4 ohm speaker 4ohm speaker

Tip

Make the terminal connection as illustrated below:•

Connect car audio

Option 1: High level input connection

Connect the amplier to your car audio with the supplied High level

input connector.

Left speaker

Right speaker

RedWhite

Car audio unit

320Hz

30Hz

SUB

WOOFER

SUBSONIC

ON OFF

REMOTE

LEVEL CONTROL

Option 2: Line input connection

Connect the amplier to the car audio with a RCA cable (not supplied).

LINE OUT

Car audio unit

320Hz

30Hz

SUB

WOOFER

SUBSONIC

ON OFF

REMOTE

LEVEL CONTROL

Connect power

1Make the power connection as illustrated below:

Connect the ground wire from the car to the• GND socket.

Connect the remote wire from the car audio to the

• REM

socket.

√ With this connection, you can turn on/off the amplier

with the car audio.

Connect the power wire from the car battery to the

• +12V

socket.

to a metal point of the car

Car audio unit

Remote output

Fuse (60 A)

+12 V car battery

less than 450 mm (18 in)

Tip

If your car audio does not have remote output, connect the remote input•

terminal (REM) to the accessory power supply.

3. Use your power amplier

Adjust input level

You can adjust the input voltage from 0.3V to 6V.

1Rotate INPUT LEVEL to adjust input voltage.

Adjust bass boost

You can punch extra bass for 0 to 12dB.

1Rotate BASS BOOST to punch for extra bass.

About the protector indicator

The amplier has a built-in protection circuit to protect the transistors

and speakers when:

The unit is overheated. Or

•

A DC current is generated. Or•

The battery voltage is over low or over high. Or•

The speaker terminals are short circuited.•

When the PROTECTOR indicator lights up in red,

the unit shuts down automatically. If this happens, please:

Left speaker

Right speaker

RedWhite

Car audio unit

320Hz

30Hz

SUB

WOOFER

SUBSONIC

ON OFF

REMOTE

LEVEL CONTROL

Left speaker

Right speaker

RedWhite

Car audio unit

320Hz

30Hz

SUB

WOOFER

SUBSONIC

ON OFF

REMOTE

LEVEL CONTROL

Left speaker

Right speaker

RedWhite

Car audio unit

320Hz

30Hz

SUB

WOOFER

SUBSONIC

ON OFF

REMOTE

LEVEL CONTROL

1Take out the disc or tape and turn off the car audio.

2Check the cause of the malfunction (see above).

3 If the amplier has overheated, wait until the unit cools down

before use.

Adjust subwoofer frequency

You can adjust the frequency of connected subwoofer.

1Rotate SUBWOOFER to adjust frequency:

30Hz to 320Hz.

Turn subsonic on or off

1Slide the SUBSONIC switch to ON position.

The subsonic is turned on.•

To turn off the subsonic feature, slide the•

SUBSONIC switch to OFF position.

Left speaker

Right speaker

RedWhite

Car audio unit

320Hz

30Hz

SUB

WOOFER

SUBSONIC

ON OFF

REMOTE

LEVEL CONTROL

Left speaker

Right speaker

RedWhite

Car audio unit

320Hz

30Hz

SUB

WOOFER

SUBSONIC

ON OFF

REMOTE

LEVEL CONTROL

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Philips Amplificateur

Philips

Philips CMP200 Manuel utilisateur

Philips

Philips Plena Mode d’emploi

Philips

Philips TDA7050T Manuel utilisateur

Philips

Philips TDA7056A Manuel utilisateur

Philips

Philips SDW5005 Manuel utilisateur

Philips

Philips TDA5360 Manuel utilisateur

Philips

Philips NE5512 Manuel du propriétaire

Philips

Philips BGD602 Manuel utilisateur

Philips

Philips 22-RH-752 Manuel utilisateur

Philips

Philips SWV2116 Manuel utilisateur

Philips

Philips TDA8542 Manuel utilisateur

Philips

Philips CMP400 Manuel utilisateur

Philips

Philips BGY89 Manuel utilisateur

Philips

Philips DFA 888 Manuel utilisateur

Philips

Philips TDA1576T Manuel utilisateur

Philips

Philips BGY148A Manuel utilisateur

Philips

Philips BGY280 Manuel utilisateur

Philips

Philips NE5205A Manuel utilisateur

Philips

Philips BGY86 Manuel utilisateur

Philips

Philips FA761 Manuel utilisateur

Philips

Philips CR6927 Manuel utilisateur

Philips

Philips TDA7050 Manuel utilisateur

Philips

Philips FA 951 Manuel utilisateur

Philips

Philips FA 911 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur