Philio PAN07-1C Manuel utilisateur

PAN07-1C/-2C/-3C PAN09-1C/-2C/-3C

TWO SPDT Switch module with meter

Fig 1. PAN07 Assembling

Fig 2. PAN0 Assembling

This in-wall dual relay switch module is a transceiver which is a Z-Wave Plus

enabled device and is fully compatible with any Z-Wave

enabled network. Mini

size design let the module can easily hide itself into the wall box and that will be

good for the house decoration.

There are many kind of application by using the module to switch AC power On

and Off, one main application is the light control. The new smart relay calibration

technology can reduce the inrush current caused by the load and let the module

work perfectly with many kind of light like incandescent, fluorescent and LED

light.

This in-wall switch module is able to detect Instant power wattage and overload

current (6A with r

esistive load

) of connected light or appliances. When detecting

overload state, the Module will be disabled and its On/Off button will be lockout

of which LED will flash quickly. However, disconnect and re-connect the Module

will reset its overload condition to normal status.

Adding to Z-Wave

Network

In the front of casing, there is an on/off button with LED indicator below which is

used to toggle switch on and off or carry out inclusion, exclusion, reset or

association. When first power is applied, its LED flashes on and off alternately

and repeatedly at 0.5 second intervals. It implies that it has not been assigned a

node ID and start auto inclusion.

Auto Inclusion

The function of auto inclusion will be executed as long as the in wall switch does

not have Node ID and just connect the switch to main power.

Note: Auto inclusion timeout is 2 minute during which the node information of

explorer frame will be emitted once every several seconds. Unlike “inclusion”

function as shown in the table below, the execution of auto inclusion is free from

pressing the On/Off button on the Switch.

The table below lists an operation summary of basic Z-Wave functions. Please

refer to the instructions for your Z-Wave

Certificated Primary Controller to

access the Setup function, and to include/exclude/associate devices

Function Description

Annotation

No node ID The Z-Wave Controller does not allocate

a node ID to the Switch. LED 2-second on,

2-second off

Inclusion 1. Put your Z-Wave controller into

inclusion mode by following the

instructions provided by the

controller manufacturer.

one press one flash LED

2. Pressing INCLUDE_BUTTON three

times within 2 seconds will enter

inclusion mode.

Exclusion 1. Put your Z-Wave controller into

exclusion mode by following the

instructions provided by the

controller manufacturer.

one press one flash LED

Pressing INCLUDE_BUTTON three

times within 2 seconds will enter

exclusion mode.

3. Node ID has been excluded. LED 0.5s On, 0.5s Off

(Enter auto inclusion)

Reset 1. Pressing INCLUDE_BUTTON three

times within 2 seconds will enter

inclusion mode.

Use this procedure only in

the event that the primary

controller is lost or

otherwise inoperable.

2. Within 1 second, press On/Off

button again for 5 seconds.

3. IDs are excluded. LED 0.5s On, 0.5s Off

(Enter auto inclusion)

Association 1. The PAN11 is an always listening

Z-Wave device, so associations

be added or removed by a controller

at any time.

Or If your controller requires to have

the PAN11 send a 'node information

frame' or NIF for associations,

pressing the On/Off button three

times within 2 seconds will cause

the PAN11 to send its NIF.

one press one flash LED

2. There are 3 groups for the switch



Including a node ID allocated by Z-Wave Controller means inclusion. Excluding a node

ID allocated by Z-Wave Controller means exclusion.



Failed or success in including/excluding the node ID can be viewed from the Z-Wave

Controller.

Sometimes people are not easy to execute exclusion or inclusion especially

when PAN07 already installed in a wall box. To solve this issue, PAN07 support

a special feature that can use S1 or S2 to execute exclusion, inclusion, Reset or

Association” at the first 3 minutes when first time connect to main power. PAN09

does not support S1/S2 function.

LED Indication

To distinguish what mode the switch is in, view from the LED for identification.

State Type LED Indication

Normal Whatever we switch On and off of the PAN07/PAN09 by S1 S2 or

On/Off button or RF command, the LED will lights up 1 second and

then off.

No node ID Under normal operation, when the Switch has not been allocated a

node ID, the LED flashes on and off alternately at 2-second

intervals. By pressing S1 S2 or On/Off button, it will stop flashing

temporarily.

Learning When PAN07/PAN09 is in learning mode, LED flashes on and off

alternately and repeatedly at 0.5 second intervals.

Overload When overload state occurs, the Switch is disabled of which LED

flashes on and off alternately at 0.2 second intervals. Overload

state can be cleared by disconnect and reconnect the Switch to the

main power

Choosing a Suitable Location

1. Do not locate the Switch facing direct sunlight, humid or dusty place.

2. The suitable ambient temperature for the Switch is 0°C~40°C.

3. Do not locate the Switch where exists combustible substances or any

source of heat, e.g. fires, radiators, boiler etc.

After putting it into use, the body of Switch will become a little bit hot of

which phenomenon is normal.

Installation

1. Put in wall switch into a wall box and connect the AC power wire L,N to

PAN07/PAN09 connector L, N.

2. Connect the wall switch to the PAN07/PAN09 as Fig1/Fig2 .

3. To manually turn ON the Switch, press and release the On/Off button. The

LED will light ON for 1 second, and the load plugged into the Switch will

also turn ON.

4. To manually turn OFF the Switch, simply press and release the On/Off

button. The LED will light ON for 1 second and the load plugged into the

Switch will turn OFF.

Programming

1. Basic Command Class / Binary Switch Command Class

The Switch will respond to BASIC and BINARY SWITCH commands that

are part of the Z-Wave system.

1-1 BASIC_GET / BINARY_SWITCH_GET

Since the switch have two relay, the Switch will report its On/Off state to

the Controller by setting Configuration parameter 3.

Configuration parameter 3=1(default)

Report ON when either relay 1 ON or relay 2 ON

Report OFF when both relay 1 and relay 2 OFF

Configuration parameter 3=2 Report ON when relay 1 ON

Report OFF when relay 1 OFF

Configuration parameter 3=3 Report ON when relay 2 ON

Report OFF when relay 2 OFF

Basic Get Command: [Command Class Basic, Basic Get]

Basic Report Command:

Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)]

Report ON:[Command Class Basic, Basic Report, Value = 255(0xFF)]

Binary Switch Get Command:[Command Class Switch Binary, Switch

Binary Get]

Binary Switch Report Command:

Report OFF:[Command Class Switch Binary, Switch Binary Report, Value

=0(0x00)]

Report ON:[Command Class Switch Binary, Switch Binary Report, Value

= 255(0xFF)]

Note: If the BASIC_GET/SWITCH_GET command follow the switch On/Off

command, it should add 0.5s time delay before the Get command.

1-2 BASIC_SET / SWITCH_BINARY_SET

Since the switch has two relay, the load attached to the Switch will turn on

or off upon receipt of the following commands from a Z-Wave Controller by

setting Configuration parameter 3.

Configuration parameter 3=1(default) switch ON and OFF both relay 1

and relay 2

Configuration parameter 3=2 switch ON and OFF of relay 1

Configuration parameter 3=3 switch ON and OFF of relay 2

[Command Class Basic, Basic Set, Value = 1~99, 255(0xFF)]: the load

attached to the Switch turns on.

[Command Class Basic, Basic Set, Value = 0(0x00)]: the load attached to

the Switch turns off.

[Command Class Switch Binary, Switch Binary Set, Value = 1~99,

255(0xFF)]: the load attached to the Switch turns on.

[Command Class Switch Binary, Switch Binary Set, Value = 0(0x00)]: the

load attached to the Switch turns off.

1. Z-Wave’s Groups (Association Command Class Version 2)

The Switch can be set to send reports to control associated Z-Wave devices. It

supports 3 association groups which every group has one node support.

Group1~Group3 support SWITCH_BINARY_REPORT,

METER_REPORT_COMMAND_V3

For group 1, the Switch will report (1) ON/OFF status of Relay1 and Relay2 (2)

Instant Power Consumption (Watt) of Relay1 and Relay2 (3) Accumulated

Power Consumption (KWh) of Relay1 and Relay2 to Z-Wave Controller.

For group 2, the Switch will report (1) ON/OFF status of Relay1 (2) Instant

Power Consumption (Watt) of Relay1 (3) Accumulated Power Consumption

(KWh) of Relay1 to Z-Wave Controller.

For group 3, the Switch will report (1) ON/OFF status of Relay2 (2) Instant

Power Consumption (Watt) of Relay2 (3) Accumulated Power Consumption

(KWh) of Relay2 to Z-Wave Controller.

2-1 Auto report to Grouping 1 ~3(Maximum Node 1)

2-1-1 On/Off Event Report

When “on” or “off” state has been changed, it will send Binary Switch Report

to the nodes of Group1~3.

Binary Switch Report

ON:[Command Class Switch Binary, Switch Binary Report, Value

=255(0xFF)]

OFF:[Command Class Switch Binary, Switch Binary Report, Value

=0(0x00)]

2-1-2 Instant Power Consumption vary over 5% report

When the power consumption of load vary over 5%, it will send Meter report

to the nodes of Group

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =

0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ]

2-1-3 overload alarm report command

When PAN07/PAN09 detect the overload , it will send Alarm Report to the

correspond Group。

The content of Alarm Report

Alarm report command:

[Command_Class_Alarm, Alarm_Report, Alarm Type =

[Command_Class_Alarm, Alarm_Report, Alarm Type = [Command_Class_Alarm, Alarm_Report, Alarm Type =

[Command_Class_Alarm, Alarm_Report, Alarm Type =

0x08, Alarm Level = 0xFF]

0x08, Alarm Level = 0xFF]0x08, Alarm Level = 0xFF]

0x08, Alarm Level = 0xFF]

2-2 Response to Meter Get Command

The Switch will report its (1) instant Power Consumption (Watt) or (2)

accumulated power consumption(KWH) or (3)

AC load Voltage (V) or (4)

load current ( I ) (5)

load power factor (PF) to Z-Wave Controller after

receive the Meter Get Command from Z-Wave Controller.

2-2-1 Instant Power Consumption (Watt) of Switch

When receiving Meter Get Command, it will report Meter Report Command

to the node asked.

Meter Get Command: [Command Class Meter, Meter Get, Scale

=0x02(W)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =

0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ]

Example:

Meter Value 1 = 0x00 (W)

Meter Value 2 = 0x00 (W)

Meter Value 3 = 0x03 (W)

Meter Value 4 = 0xEA (W)

Meter(W) = Meter Value 3 *256 + Meter Value 4 = 100.2W

2-2-2 Accumulated Power Consumption (KW/h)

When receiving Meter Get Command, it will report Meter Report

Command to the node asked.

Meter Get Command:

[Command Class Meter, Meter Get, Scale = 0x00 KW/h)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01， Meter Type

=0x01， Precision = 2，Scale = 0x00，Size = 4，Meter Value (KWh)]

Example:

Scale = 0x00 (KWh)

Precision = 2

Size = 4 Bytes (KW/h)

Meter Value 1 = 0x00(KWh)

Meter Value 2 = 0x01(KWh)

Meter Value 3 = 0x38(KWh)

Meter Value 4 = 0xA3(KWh)

Accumulated power consumption (KW/h) = (Meter Value 2*65536) +

(Meter Value 3*256) + (Meter Value 4) = 800.35 (KW/h)

2-2-3 Clearing accumulated power consumption

Whenever re-start counting the accumulated power consumption is needed,

you can use Meter Reset Command to clear it.

Meter Reset Command: [Command Class Meter, Meter Reset]

2-2-4 AC load Voltage (V)

When receiving Meter Get Command, it will report Meter Report Command

to the node asked.

Meter Get Command: [Command Class Meter, Meter Get, Scale =0x04(V)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =

0x01，Precision = 1，Scale = 0x04，Size = 2， Meter Value(V)]

Example:

Scale = 0x04 (V)

Precision = 1

Size = 2 (2 Bytes of V)

Meter Value 1 = 0x09(V)

Meter Value 2 = 0x01(V)

AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V)

2-2-5 AC load current ( I )

When receiving Meter Get Command, it will report Meter Report Command to

the node asked.

Meter Get Command: [Command Class Meter, Meter Get, Scale =0x05(I)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =

0x01，Precision = 2，Scale = 0x05，Size = 2，Meter Value(I)]

Example:

Scale = 0x05 (I)

Precision = 2

Size = 2 (2 Bytes of I)

Meter Value 1 = 0x01(I)

Meter Value 2 = 0x21(I)

AC load current = (Meter Value 1*256) +(Meter Value 2)= 2.89 (A)

2-2-6 load power factor (PF)

When receiving Meter Get Command, it will report Meter Report Command to

the node asked.

Meter Get Command: [Command Class Meter, Meter Get, Scale =0x06(PF)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =

0x01， Precision = 2，Scale = 0x06，Size = 1 Bytes，Meter Value(PF)]

Example:

Scale = 0x06 (PF)

Precision = 2

Size = 1 (1 Byte of PF)

Meter Value 1 = 0x63(PF) (It means that the load power factor is 0.99)

2-3 Multi Channel Command Class Version 3

PAN07/PAN09 also support Muti Channel command class (version 3), which

include BINARY_SWITCH_GET, BINARY_SWITCH_SET, BASIC_GET,

BASIC_SET, METER_SUPPORTED_GET, METER_RESET, METER_GET.

You may control or get report from 3 endpoints of PAN07/PAN09.

2-3-1 BINARY_SWITCH_GET

You may get the ON/OFF state from every endpoint, when endpoint set to 1 ,

PAN07/PAN09 will reply ON(0xFF) either Relay 1 or Relay2 is ON, report

OFF (0x00) when both Relay 1 and Relay2 OFF. If endpoint set to 2,

PAN07/PAN09 will reply state of Relay1 . If endpoint set to 3 and

PAN07/PAN09 will reply state of Relay2

Below is an example show a source endpoint 5 send a get command to

PAN07/PAN09 endpoint 1

COMMAND_CLASS_MULTI_CHANNEL

MULTI_CHANNEL_CMD_ENCAP

Source End Point = 0x05 (this is the endpoint of command owner

here we assume endpoint is 5，

if the

owner doesn’t support multi

Channel this value will be 0)

(Bit Address+Destination End Point = 0x01)

(Bit Address =0；Destination End Point

range from 1~3)

Command Class = 0x25 (Command_Class_Switch_Binary =

0x25)

Command =0x02 (Switch_Binary_Get = 0x02)

Below is the example show PAN07/PAN09 report to last command

COMMAND_CLASS_MULTI_CHANNEL

MULTI_CHANNEL_CMD_ENCAP

Source End Point = 0x01 Since the endpoint is 1 so PAN07

/PAN09 will reply ON(0xFF) either Relay

1 or Relay2 is ON, report OFF (0x00)

when both Relay 1 and Relay2 OFF

(Bit Address+Destination End Point = 0x05)

(Bit Address =0；Destination End Point)

Command Class = 0x25 (Command_Class_Switch_Binary =

0x25)

Command =0x03 (Switch_Binary_Reportet = 0x3)

Parameter 1 = 0xFF (ON=0xFF ，OFF=0x00)

Note: If the Multi-Channel Encapsulated BASIC_GET/SWITCH_GET

command follow a switch On/Off command, it should add 0.5s time

delay before the Get command.

2-3-2 BINARY_SWITCH_SET

By using BINARY_SWITCH_SET Command of Multi Channel Command Class

Encapsulation Command, you can switch both Relay1 and Relay2 ON/OFF by

setting endpoint to 1 or switch Relay1 ON/OFF by setting endpoint to 2 or switch

Relay2 ON/OFF by setting endpoint to 3

The example of the command show that switch off relay1 of PAN07/PAN09

COMMAND_CLASS_MULTI_CHANNEL

MULTI_CHANNEL_CMD_ENCAP

Source End Point = 0x01 (this is the endpoint of command owner

here we assume endpoint is 1，if the

owner doesn’t support multi Channel

this value will be 0)

(Bit Address+Destination End Point = 0x02)

(Bit Address =0；Destination End Point

range1~3)

Command Class = 0x25 (Command_Class_Switch_Binary =

0x25)

Command =0x01

(Switch_Binary_Set = 0x01)

Parameter 1 = 0x00 (ON=0xFF ，OFF=0x00)

2-3-3 METER_SUPPORTED_GET：

：：

：

This command is to ask the endpoint of PAN07/PAN09 what kind of meter data

can be reported

The example show how to get the meter report type

COMMAND_CLASS_MULTI_CHANNEL

MULTI_CHANNEL_CMD_ENCAP

Source End Point = 0x01 (this is the endpoint of command owner

here we assume endpoint is 1，if the

owner doesn’t support multi Channel

this value will be 0)

(Bit Address+Destination End Point = 0x03)

(Bit Address =0；Destination End Point

range1~3)

Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)

Command =0x03 (Meter_Supported_Get = 0x03)

Below is the example show PAN07/PAN09 report to last command

COMMAND_CLASS_MULTI_CHANNEL

MULTI_CHANNEL_CMD_ENCAP

Source End Point = 0x03

(Bit Address+Destination End Point = 0x01)

Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)

Command =0x04 (Meter_Supported_Report = 0x04)

Parameter 1 = 0x81 (Meter Reset =1 ，Meter Type=0x01)

Parameter 2 = 0x75 (Scale Supported =

KWh+W+V+A+Power Factor = 0x75)

2-3-4 METER_RESET

This command is to reset the Accumulated Power Consumption (KWh) to 0

The example show how to reset the KWh

COMMAND_CLASS_MULTI_CHANNEL

MULTI_CHANNEL_CMD_ENCAP

Source End Point = 0x03

(this is the endpoint of command owner,

here we assume endpoint is 3，if the

owner doesn’t support multi Channel

this value will be 0)

(Bit Address+Destination End Point = 0x01)

(Bit Address =0；Destination End Point

range1~3)

Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)

Command =0x05 ( Meter_Reset = 0x05)

2-3-5 METER_GET：

：：

：

Using meter get command to get the KWH,W,V,I,PF from endpoint of

PAN07/PAN09

2-3-5-1 Get KWH from endpoint

Meter_GET example:

COMMAND_CLASS_MULTI_CHANNEL

MULTI_CHANNEL_CMD_ENCAP

Source End Point = 0x05

(this is the endpoint of command owner,

here we assume endpoint is 5，if the

owner doesn’t support multi Channel

this value will be 0)

(Bit Address+Destination End Point = 0x03)

(Bit Address =0；Destination End Point

range1~3)

Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)

Command =0x01 (Meter_Get = 0x01)

Parameter 1 = 0x00 (Scale = KWH = 0x00)

Accumulated power consumption (KWH) Report example：

COMMAND_CLASS_MULTI_CHANNEL

MULTI_CHANNEL_CMD_ENCAP

Source End Point = 0x03 (Meter report = Endpoint3)

(Bit Address+Destination End Point = 0x05)

(Bit Address =0；

Destination End Point =

command owner Endpoint value)

Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)

Command =0x02 (Meter_Report = 0x02)

Parameter 1 = 0x21 (Scale Bit2 = 0 ，Rate Type = 0x01，

Meter Type=0x01)

Parameter 2 = 0x44 (Precision = 2，Scale Bit1Bit0 = 0，

Size =

Parameter 3 = 0x00 Accumulated Power Consumption =

0x000005FD = 15.33 KWh

Parameter 4 = 0x00

Parameter 5 = 0x05

Parameter 6 = 0xFD

2-3-5-2 Get Instant Power Consumption (Watt) from endpoint

METER_GET example：

COMMAND_CLASS_MULTI_CHANNEL

MULTI_CHANNEL_CMD_ENCAP

Source End Point = 0x05 (this is the endpoint of command owner,

here we assume endpoint is 5，

if the owner

doesn’t support multi Channel this value

will be 0)

(Bit Address+Destination End Point =

0x03)

(Bit Address =0；Destination End Point

range 1~3)

Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)

Command =0x01 (Meter_Get = 0x01)

Parameter 1 = 0x10 (Scale = W = 0x02)

PAN07/PAN09 Instant Power Consumption (W) Report example：

COMMAND_CLASS_MULTI_CHANNEL

MULTI_CHANNEL_CMD_ENCAP

Source End Point = 0x03 (Meter report = Endpoint3)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Philio Unité de contrôle

Philio

Philio PAN03 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur