Perun ETU++ Manuel utilisateur

ETU++

Manual

Perun ETU++ replaces stock electronics in replicas with Electronic Trigger Unit by G&G. It

provides lots of additional features, as well as allows the replica to work with many different

battery types. Reading this manual will help you fully exploit this unit’s potential and in case

of encountering any problems, you can look here for solutions.

Manufacturer:

Perun

Barwicka 8 St.

60-192 Poznań

Poland

e-mail: info@perunairsoft.pl

Table of contents

1. Technical data.................................................................................................................................. 2

2. Features and programming............................................................................................................. 2

3. Factory settings ............................................................................................................................... 4

4. Diagnostic system............................................................................................................................ 5

5. Switch check.................................................................................................................................... 7

6. Custom/DIY projects........................................................................................................................ 7

1. Technical data

Recommended power sources

Perun ETU++ works with any power source that provides a voltage between 7 and 17 volts and can

deliver enough current to ensure smooth cycling of the replica. Li-Po and Li-Ion batteries with a

nominal voltage of 7.4, 11.1 or 14.8 volts are recommended. It is also advised to use batteries with

possibly high „C” parameter and capacity. This is safer for the battery, as it should not be working on

the edge of its capability. In this video, we are showing why:

https://www.youtube.com/watch?v=s8RKcIy810A

Capacity and the „C” parameter also influence the rate of fire of the replica:

https://www.youtube.com/watch?v=5hO25aPvHcU

Compatibility with high-ROF and high-power builds

Perun ETU++ can work with even the most demanding setups, both regarding rate of fire and muzzle

velocity.

Electronic fuse

Perun ETU++ has an integrated electronic fuse, which will automatically cut the power off in case of a

short circuit or when a gearbox jam is detected. The fuse does not wear out or need to be replaced.

Battery connector type

Perun ETU++ comes with an already soldered T-Plug connector.

Power consumption when idle

Don’t leave the battery connected to the replica, when you are not using it! When idle (battery

connected, replica not shooting) ETU++ consumes 0,75mA. To put it in context, this would drain a half-

laden 1200mAh battery in around a month.

2. Features and programming

To enter the programming mode:

•For “SEMI” –keep the selector on “SEMI” for a couple

of seconds, then go to “AUTO” and back, twice.

(“SEMI” → “AUTO” → “SEMI” → “AUTO” → “SEMI”)

Successful entry into the programming mode for “SEMI”

will be confirmed by one sound signal and the blue LED

light.

•For “AUTO” –keep the selector on “AUTO” for a

couple of seconds, then go to “SEMI” and back, twice.

(“AUTO” → “SEMI” → “AUTO” → “SEMI” → “AUTO”)

Successful entry into the programming mode for “AUTO”

will be confirmed by three sound signals and the red LED

light.

Switching the selector between “AUTO” and “SEMI” and

back allows to move between the modes. Pulling the trigger

allows to enable, disable, or set levels for the modes.

Full feature description

All the settings are set independently for “SEMI” and “AUTO” selector positions, except for Li-Po

alarm and Master reset, which work for both selector positions.

Video manual is available here: https://youtu.be/OxTmKhq7bs8

Function and

LED color

Description

Firing mode

Green

Choose one of the firing modes for any selector position: safe, semi, 2-5 shot burst

and, auto.

No sound signal, steady green light –safe

1 short single signal and blink –semi

2-5 short signals and blinks –2-5 round burst

1 long signal and blink - auto

Blue

Active brake (AB) stops the motor after the shot, preventing the spring from

remaining in a compressed state and eliminates double shots on semi in replicas with

a high rate of fire (“overspin”). 5 levels of braking strength are available –from 1

(weakest braking) to 5 (the strongest). Braking can be also completely disabled. It is

advised not to use braking all the time, if not necessary, or to use it on the lowest

possible level, because strong braking negatively impacts the service life of motor

brushes and causes increased heating.

Tip: Switch to semi, fire a single shot and hold the trigger after the shot. This will cause

a second single shot with the strongest AB setting to be fired after 2 seconds, making

sure the main spring remains uncompressed. It is advised to do that when you finish

shooting for the day.

No sound signal while LED glows blue means, that the active brake is disabled. 1 to 5

signals indicate braking levels from 1 (the weakest) to 5 (the strongest).

Attention! While precocking is on, the AB setting becomes irrelevant. However, any

programmed AB setting will be stored in memory and will become effective as soon as

precocking is disabled.

Precocking

Yellow

When shooting on semi, precocking keeps the piston in the rear position, ready for

the shot. This decreases the time between pulling the trigger and the actual shot,

increasing realism, and giving an advantage in CQB fights. Precocking level must be

set individually to each replica and according to user preferences. Precocking power

is automatically adjusted to battery voltage and semi or automatic shots.

Tip: To release the spring after using precocking, switch to semi, fire a single shot, and

hold the trigger after the shot. This will cause a second single shot with the strongest

AB setting to be fired after 2 seconds, making sure your spring remains uncompressed.

It is advised to do that when you finish shooting for the day.

No sound signal while LED glows yellow means, that the precocking is disabled. 1 to 8

signals indicate precocking levels from 1 (the weakest) to 8 (the strongest).

Attention! The AB setting does not affect the functioning of precocking, it is ignored if

precocking is enabled.

Binary trigger

Purple and

teal blinking

alternately

The binary trigger allows the semi shots to be triggered not only after the pull but also

after the release of the trigger.

Tip: Hold the trigger for 2 seconds to cancel the second shot.

No sound signal while LED blinks purple and teal alternatively means, that the binary

trigger is disabled. 1 signal indicates activation of the binary trigger.

Function and

LED color

Description

ROF reduction

White

This function allows to lower the rate of automatic fire. 5 reduction levels are

available:

1 –6% ROF reduction

2 –12% ROF reduction

3 –18% ROF reduction

4 –24% ROF reduction

5 –30% ROF reduction

Attention! Those are approximate values and may vary depending on replica

configuration.

No sound signal while LED glows white means, that the ROF reduction is disabled. 1

to 5 signals indicate reduction levels from 1 (the smallest) to 5 (the greatest).

Attention! Semi-automatic shots and the first shot in burst are always fired without

any power reduction to retain good trigger response.

DMR mode

Purple

DMR Mode allows only semiautomatic shots and limits their frequency. Its main use

is for high power, DMR-styled replicas on fields,which demand such limitations.0.25s,

0.5s, 1s, 2s and 3s intervals are available.

No sound signal while LED glows purple means, that the DMR mode is disabled. 1 to

5 signals indicate interval levels from 1 (the shortest) to 5 (the longest).

Li-Po and Li-

Ion alarm

Teal

Li-Po and Li-Ion alarm informs the user that battery voltage has fallen below 3.7V per

cell, at which the battery should not be further used and must be recharged. The unit

automatically detects the number of cells in the battery and determines a safe voltage

range.

The need for battery replacement is signaled by short sound signals every one minute.

Disable this function if you are using batteries other than Li-Po or Li-Ion.

No sound signal while LED glows white means, that the alarm is disabled. 1 signal

indicates activation of the alarm.

Master reset

Red

Master reset returns the unit to the factory settings.

To reset, pull and hold the trigger for 2 seconds. A long sound signal confirms return

to factory settings.

3. Factory settings

New units and units, where master reset was activated, will have modes set in a following way:

•Firing mode –semi on “SEMI” and auto on “AUTO”

•AB –level 3

•Precocking –disabled

•Binary trigger - disabled

•ROF reduction –disabled

•DMR Mode –disabled

•Li-Po and Li-Ion alarm –enabled

4. Diagnostic system

Perun ETU++ has a diagnostic system that will help you find the source, should you encounter a

problem. After the battery is connected, the unit undergoes a start-up check, to make sure the replica

is ready to work. Successful completion of this check is indicated by a short green blink of the LED.

Problem and LED color

Description

Disconnected motor /

Switch check

Yellow, blinking

This not only provides information about the disconnection of the

motor, but it is also a switch check mode for the trigger, selector, and

sector gear switches. With the motor disconnected, engaging the

switches will cause the LED to glow purple (trigger), green (selector),

or blue (sector gear) for a moment. This can be used for

troubleshooting problems with the switchboard in the gearbox.

Reconnecting the motor will restore normal function.

Attention: Motor check only takes place at start-up. A disconnection

after the start-up will not be signaled!

Fuse activation

Red, continuous, or blinking

Activation of the fuse with a distinction between a short circuit

(continuous red) and gearbox jam (blinking red). In some situations,

this distinction may not be correct, for instance, a gearbox jam may

be incorrectly read as a short circuit and vice versa.

The unit will start functioning normally after the battery is

reconnected, unless there still is a short circuit that will be detected

at the next start-up.

Trigger pull detected during

start-up

Yellow and purple blinking

alternately

The unit detected that the trigger was being held during start-up. This

can also indicate a short circuit of the signal wiring or mechanical

malfunction of the trigger mechanism.

The unit will start functioning normally after the trigger is released.

Gearbox cycle detection

failure

Yellow and green blinking

alternately

The unit did not receive information about cycle end from the sector

gear switch and stopped firing only after safety time limit was

exceeded. This may indicate a problem with the switch, cut-off lever,

or damaged wire.

Unit temperature is too high

Yellow and white blinking

alternately

Too high temperature of the unit (electronic board) was detected. It

will not function again until it cools down, after which it will operate

normally.

Battery with too low voltage

is connected

Yellow and teal blinking

alternately

The battery with a voltage below 7V is connected. Change the battery

to one with voltage between 7V and 17V.

Battery with too high

voltage is connected

Red and teal blinking

alternately

The battery with a voltage over 17V is connected. The battery must

be immediately disconnected, as it can cause permanent damage!

Change the battery to one with a voltage between 7V and 17V.

Problem and LED color

Description

Main transistor or driver

damage

Red and yellow blinking

alternately

Main transistor or driver is damaged. Unit needs to be sent back for

repair.

Battery voltage sensing

malfunction

Red and white blinking

alternately

Battery detection system is malfunctioning. The unit needs to be sent

back for repair.

Other known problems:

Problem

Cause

Solution

Replica fires a

2-round burst

in semi-auto

mode.

Motor and battery are too strong

for the main spring, which causes

overspin.

Enable AB or precocking.

Too high precocking level.

Set precocking to a lower level.

Trigger mechanism malfunction.

Check the cut-off lever and contacts, replace

if needed.

Replica does

not shoot; the

unit does not

emit any light

or sound.

Incompatible T-Deans battery

connector.

T-deans plugs and sockets from various

manufacturers may sometimes not work

together reliably. Although the plug may

seem to fit the socket nicely, the conductive

surfaces may not contact each other, cutting

the power off. In that case try with another

battery, most preferably with a T-deans

socket made by a different manufacturer.

Battery

and/or the

motor heat up

very much.

The battery has a too low capacity

(mAh) and/or the “C” parameter.

Use a battery with higher capacity and/or

the “C” parameter.

The motor is too weak.

Use a stronger motor, possibly with

neodymium magnets.

Increased motor load caused by

excessive friction, for example

caused by:

- improper shimming,

- motor positioned askew in the

pistol grip.

Remove the cause of the friction.

Motor beeps

from time to

time

Li-Po alarm has activated

Replace the battery (if you’re not using a Li-

Po or Li-Ion, disable the Li-Po alarm).

The same

battery

and/or motor

did not heat

up earlier.

Low-resistance MOSFET transistor and wiring used in Perun ETU++ provide

resistance much lower than mechanical contacts and some other MOSFET circuits.

According to Ohm’s law, that allows more current to be drawn from the battery

and directed to the motor. This makes the trigger response and rate of fire faster,

but a higher current draw also leads to increased heating of electronic elements.

This may become too demanding for the previous battery and/or motor and a

need to change to new ones may arise.

Attention! In case of any technical questions, please contact us at: info@perunairsoft.pl

5. Switch check

You can easily check the switch set in the gearbox by disconnecting the motor. When ETU++ is

connected to the battery, but disconnected from the motor, it informs about this by yellow, flashing

light. If during that flashing a properly working and connected switch will be closed, the unit will signal

that by changing the LED color for a moment.

Attention! To enter this mode, the motor must be disconnected first, only then connect the battery!

Attention! After you enter the switch check mode, it will be active for 5 minutes, after which the unit

will shut down. To restart it, simply reconnect the battery.

LED color

Switch

Disconnected motor /

Switch check

Yellow, blinking

No switch activation is being detected at this moment

Selector switch was closed

Red

This should happen after the selector is set to “AUTO”.

Selector switch was opened

Blue

This should happen after the selector is switched from “AUTO” to

any other position.

Trigger

Purple

The trigger switch was closed.

Sector gear

Green

The sector gear switch was closed.

Checking the trigger and selector sensor can be done by simply pulling the trigger or switching the

selector between “SEMI” and “AUTO” positions. This can be done without any disassembly of the

replica.

In order to check the sector gear switch, it’s best to open the gearbox and remove everything out of

it, except for the switches and the sector gear (make sure to keep the shimming the same as in

assembled replica, it can influence whether the switch would work or not). Then roll the sector gear

by hand and see, whether the color of the light changes to green.

6. Custom/DIY projects

ETU++ is a perfect solution for teching enthusiasts, who engage in creating totally custom projects and

need a firing control unit. If you have inputs from switches installed on trigger, selector, and sector

gear cut-off, but need electronics that would steer the replica using information from those switches,

ETU++ is the way to go. It may also help in converting replicas known to have problems with trigger or

cut-off mechanism, like P90 or Steyr AUG, to a switch-based operation. Below are the details on how

to properly prepare the wiring to make it work with ETU++.

Switch wiring scheme

ETU++ socket has 4 pins for 4 signal wires. Of those, 3 are for selector, trigger, and sector gear cut-off

(information about cycle end) and the 4th is a common ground, to which all the switches must be

connected.

Do not allow the motor wires to get into (uninsulated) contact with any of the signal wires. This

would result in an immediate and permanent failure of the device!

Plug

The Plug that is used in G&G replicas with ETU

and works with Perun ETU++ is JST ZHR-4. It is

available in many electronic shops. We

recommend using plugs with pre-installed wires

that can be lengthened, because correct

preparation of the bare plug might be difficult.

The correct plug wiring order is shown here.

Switches

Almost any switch can be used, as ETU++ is resistant to contact bounce, while low voltage and current

used to detect switching allows using a wide variety of models. Therefore, use any switches that will

best suit your project. Here is a short description, of what does ETU++ expect from each of the

switches:

Selector: When the switch is closed, ETU++ sees it as “AUTO” and when it’s open, it sees “SEMI”. This

is pretty much irrelevant however, as the firing modes in ETU++ are freely programmable.

Please note that the safe mode can only be achieved either by a mechanical safety, or by sacrificing

one of the firing modes and making it safe by programming electronic safety.

Trigger: Switch should be closed by the movement of the trigger and opened upon releasing the trigger.

Sector gear cut-off: Once per gearbox cycle ETU++ should receive an information from a sector gear

switch, or cut-off switch. This can be achieved in many ways, but probably the easiest is by reading

either directly from the cut-off knob of the sector gear or from the cut-off lever. The amount of time

the sector gear switch is being pressed during the cycle is irrelevant, the electronic unit is only looking

for the closing of the switch.

Table des matières

Autres manuels Perun Accessoires de jeux vidéo

Perun

Perun AB++ Manuel utilisateur

Manuels Accessoires de jeux vidéo populaires d'autres marques

VENOM

VENOM VS3057 Manuel utilisateur

LINK-MI

LINK-MI HDVC01 Manuel utilisateur

Thrustmaster

Thrustmaster T60 Manuel utilisateur

Avermedia

Avermedia C875 Manuel utilisateur

VENOM

VENOM VS2728 Manuel utilisateur

DGT

DGT 960 Manuel utilisateur

Sega

Sega Visual Memory Unit Manuel utilisateur

Datel

Datel Go-tcha Expedition Manuel utilisateur

TruGolf

TruGolf TruFlight 2 Manuel utilisateur

CH Products

CH Products CH PRO THROTTLE Manuel utilisateur

Thrustmaster

Thrustmaster T2PA Manuel utilisateur

Cube Controls

Cube Controls Mercedes-AMG - GT Edition SIM Wheel Manuel utilisateur

Hoffmann

Hoffmann Club Pro Manuel utilisateur

ardistel

ardistel ADT SpeedRacer Manuel utilisateur

Sven

Sven GC-W150 Manuel utilisateur

Deltaco Gaming

Deltaco Gaming GAM-131 Manuel utilisateur

Huffy

Huffy M731324 Manuel utilisateur

Ace Bayou

Ace Bayou X Rocker Manuel utilisateur