PEP CP390 Manuel utilisateur
Preface CP390
ID 19976, Rev. 0200Page 0 - 2 ® PEP Modular Computers GmbH
Chapter 0
Preface
Preface Table of Contents.............................................0 - 4
Chapt 1
Chapter 1
1. Introduction
1.1 Overview .................................................................1 - 2
1.2 Board Interfaces .....................................................1 - 3
1.3 Block Diagram ........................................................1 - 4
1.4 Board Layout ..........................................................1 - 4
1.5 Front Panels ...........................................................1 - 5
1.6 Technical Specifications .........................................1 - 6
1.7 Applied Standards ..................................................1 - 7
1.8 Related Publications ...............................................1 - 7
Chapter 2
2. Installation
2.1 Board Installation ....................................................2 - 2
CP390 Preface
ID 19976, Rev. 0200 Page 0 - 3® PEP Modular Computers GmbH
Chapter 3
3. Configuration
3.1 Pinouts ....................................................................3 - 2
Chapter 4
4. Hotswap
4.1 Technical Background of CompactPCI Hotswap ....4 - 2
4.2 Design Implementation on the CP390 ....................4 - 4
Appendix
A
CompactPCI System Notes
ASystem Overview ....................................................A - 2
BSystem Components ..............................................A - 3
CP390 Preface
Preface
Table of Contents......................................................... 0 - 2
Revision History........................................................... 0 - 5
Trademarks.................................................................. 0 - 5
Explanation of Symbols ............................................... 0 - 6
For Your Safety............................................................ 0 - 7
High Voltage Safety Instructions.............................. 0 - 7
Special Handling and Unpacking Instructions.......... 0 - 7
General Instructions on Usage................................. 0 - 8
Two Years Warranty .................................................... 0 - 9
ID 19976, Rev. 0200 Page 0 - 4® PEP Modular Computers GmbH
Chapt 1
Chapter 0
Preface CP390
Revision History
This document contains information proprietary of PEP Modular Computers. It may not be
copied or transmitted by any means, disclosed to others or stored in any retrieval system or
media, without the prior written consent of PEP Modular Computers GmbH or one of its autho-
rized agents.
The information contained in this document is, to the best of our knowledge, entirely correct.
However, PEP Modular Computers cannot accept liability for any inaccuracies, or the conse-
quences thereof, nor for any liability arising from the use or application of any circuit, product,
or example shown in this document.
PEP Modular Computers reserve the right to change, modify, or improve this document or the
product described herein, as seen fit by PEP Modular Computers without further notice.
Trademarks
PEP Modular Computers and the PEP logo are trademarks owned by PEP Modular Comput-
ers GmbH, Kaufbeuren, Germany. In addition, this document may include names, company
logos and trademarks which are registered trademarks and are, therefore, proprietary of their
respective owners.
ID 19976, Rev. 0200Page 0 - 5 ® PEP Modular Computers GmbH
Revision History
Manual/Product Title: CP390
Manual ID Number: 19976
Rev.
Index Brief Description of Changes Board Index Date of
Issue
0100 Initial Issue 1000 Apr. 99
0200 Hotswap chapter added, description of
CompactPCI and PMC connectors added,
deletion of I/O voltage switching description
2000 Jan. 00
PrefaceCP390
ID 19976, Rev. 0200 Page 0 - 6® PEP Modular Computers GmbH
Explanation of Symbols
CE Conformity
This symbol indicates that the item described in this manual
is in compliance with all applied CE standards. See also the
section “Applied standards” of this manual.
Caution!
This symbol and title warn you of hazards due to electrical
shocks (> 60 V) when touching products or parts of them.
The non-observance of the measures indicated and/or pre-
scribed by the law may cause harm to your product and/or
life/health.
See also the section “High Voltage Safety Instructions”.
ESD-Sensitive Device!
This symbol and title inform you that electronic boards and
their components are sensitive to static electricity. There-
fore, care must be taken during all handling operations and
inspections of this product, in order to ensure product integ-
rity at all times.
Please read also the section “Special Handling and Unpack-
ing Instructions” of this manual.
Attention!
This symbol and title emphasize aspects which, if not read
through carefully by the reader, might cause hazards to
health and/or damages to material.
Note:
This symbol and title emphasize aspects the reader should
read through carefully for his or her own advantage.
PEP Advantage
This symbol and title emphasize advantages or positive
aspects of a product and/or procedure.
Troubleshooting
This symbol and title characterize a message containing
useful information on troubleshooting and problem solving.
!
$
CP390Preface
For your safety
Your new PEP product has been developed and carefully tested in order to provide all the fea-
tures necessary to ensure full compliance with all electrical safety requirements. It has also
been designed for a long fault-free life. However, the life expectancy of your product will be
drastically reduced by improper treatment during unpacking and installation. Therefore, in the
interests of your own safety and of the correct operation of your new PEP product, you are
requested to conform with the following guidelines.
High Voltage Safety Instructions
Special Handling and Unpacking Instructions
$Do not handle this product while it is outside its protective enclosure while it is not used
for operational purposes, unless it is otherwise protected.
$Whenever possible, unpack or pack this product only at EOS/ESD safe work stations.
Where safe work stations are not guaranteed, it is important for the user to be electri-
cally discharged before touching the product with his/her hands or tools. This is most
easily done by touching a metal part of your system housing.
$It is particularly important to observe standard anti-static precautions when changing
piggybacks, ROM devices, jumper settings etc. If the product contains batteries for RTC
or memory backup, ensure that the board is not placed on conductive surfaces, includ-
ing anti-static plastics or sponges. They can cause short circuits and damage the batter-
ies or tracks on the board.
Warning!
All operations on this device must be carried out by sufficiently
skilled personnel.
Caution!
The power supply must always be disconnected before installa-
tion, repair and maintenance operations are carried out on this
product. Failure to comply with this basic precaution will subject
the operator to serious electrical shock hazards. Always unplug
the power cable before such operations.
Before installing your new PEP product into a system always
ensure that your mains power is switched off. This applies also to
the installation of piggybacks.
ESD Sensitive Device!
Electronic boards and their components are sensitive to static
electricity. Therefore, care must be taken during all handling oper-
ations and inspections of this product, in order to ensure product
integrity at all times.
!
ID 16566, Rev. 0200Page 0 - 7 ® PEP Modular Computers GmbH
PrefaceCP390
General Instructions on Usage
$In order to maintain PEP’s product warranty, this product must not be altered or modi-
fied in any way. Changes or modifications to the device, which are not explicitly
approved by PEP Modular Computers and described in this manual or received from
PEP Technical Support as a special handling instruction, will void your warranty.
$This device should only be installed in or connected to systems that fulfill all necessary
technical and specific environmental requirements. This applies also to the operational
temperature range of the specific board version, which must not be exceeded. If batter-
ies are present, their temperature restrictions must be taken into account.
$When performing all necessary installation and application operations please follow only
the instructions supplied by the present manual.
$Keep all the original packaging material for future storage or warranty shipments. If it is
necessary to store or ship the board please re-pack it as nearly as possible in the man-
ner in which it was delivered.
$Special care is necessary when handling or unpacking the product. Please consult the
special handling and unpacking instructions on the preceding page of this manual.
ID 19976, Rev. 0200 Page 0 - 8® PEP Modular Computers GmbH
CP390Preface
Two Years Warranty
PEP Modular Computers grants the original purchaser of a PEP product a TWOYEAR LIMITED
HARDWAREWARRANTYas described in the following. However, no other warranties that may be
granted or implied by anyone on behalf of PEP are valid unless the customer has the express
written consent of PEP Modular Computers.
PEP Modular Computers warrants their own products, excluding software, to be free from
manufacturing and material defects for a period of 24 consecutive months from the date of
purchase. This warranty is not transferable nor extendible to cover any other users or long-
term storage of the product. It does not cover products which have been modified, altered or
repaired by any other party than PEP Modular Computers or their authorized agents. Further-
more, any product which has been, or is suspected of being damaged as a result of negli-
gence, improper use, incorrect handling, servicing or maintenance, or which has been
damaged as a result of excessive current/voltage or temperature, or which has had its serial
number(s), any other markings or parts thereof altered, defaced or removed will also be
excluded from this warranty.
If the customer’s eligibility for warranty has not been voided he should, in the event of any
claim, return the product at the earliest possible convenience to the original place of purchase,
together with a copy of the original document of purchase, a full description of the application
in which the product has been used and a description of the defect. Please pack the product in
such a way as to ensure safe transportation (see our safety instructions).
PEP provides for repair or replacement of any part, assembly or sub-assembly at the com-
pany’s own discretion, or to refund the original cost of purchase, if appropriate. In the event of
repair, refunding or replacement of any part, the ownership of the removed or replaced parts
reverts to PEP Modular Computers, and the remaining portion of the original guarantee, or
any new guarantee to cover the repaired or replaced items, will be transferred to cover the
new or repaired items. Any extensions to the original guarantee are considered gestures of
goodwill, and will be defined in the “Repair Report” issued by PEP with the repaired or
replaced item.
PEP Modular Computers will not accept liability for any further claims resulting directly or indi-
rectly from any warranty claim, other than the above specified repair, replacement or refund.
In particular, all claims for damage to any system or process in which the product was
employed, or any loss incurred as a result of the product not functioning at any given time, are
excluded. The extent of PEP Modular Computers liability to the customer shall not exceed the
original purchase price of the item for which the claim exists.
PEP Modular Computers issues no warranty or representation, either explicit or implicit, with
respect to its products’ reliability, fitness, quality, marketability or ability to fulfil any particular
application or purpose. As a result, the products are sold “as is,” and the responsibility to
ensure their suitability for any given task remains that of the purchaser. In no event will PEP
be liable for direct, indirect or consequential damages resulting from the use of our hardware
or software products, or documentation, even if PEP were advised of the possibility of such
claims prior to the purchase of the product or during any period since the date of its purchase.
Please remember that no PEP Modular Computers employee, dealer or agent is authorized to
make any modification or addition to the above specified terms, either verbally or in any other
form, written or electronically transmitted, without the company’s prior consent.
ID 19976, Rev. 0200Page 0 - 9 ® PEP Modular Computers GmbH
CP390
ID 19976, Rev. 0200
Introduction
Page 1 - 1® PEP Modular Computers GmbH
Introduction
1.1 Overview ............................................................................. 1 - 2
1.2 Board Interfaces .................................................................. 1 - 3
1.3 Block Diagram ..................................................................... 1 - 4
1.4 Board Layout ....................................................................... 1 - 4
1.5 Front Panels ........................................................................ 1 - 5
1.6 Technical Specifications ...................................................... 1 - 6
1.7 Applied Standards ............................................................... 1 - 7
1.7.1 CE Compliance ........................................................... 1 - 7
1.7.2 Mechanical Compliance .............................................. 1 - 7
1.7.3 Environmental Tests ................................................... 1 - 7
1.8 Related Publications ............................................................ 1 - 7
1.8.1 CompactPCI Systems/Boards .................................... 1 - 7
1.8.2 PMC Add-on Modules/Carriers ................................... 1 - 7
Chapter1
Table des matières
Autres manuels PEP Matériel informatique
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
