Pentium SQ578 Manuel utilisateur

SQ578 Pentium PCI

Mainboard

User’s Manual

SQ578

User‘s Notice

Static Electricity Precaution

Static electricity can easily damage your SQ578 mainboard. Observing a few basic

precautions can help you safeguard against damage that could result in expensive repairs.

Follow the simple measures below to protect your equipment from static electricity damage:

Keep the mainboard and other system components in their anti-static packaging until you are

ready to install them.

Touch a grounded surface before you remove any system component from its protective anti-

static packaging. Unpacking and installation should be done on a grounded, anti-static mat.

The operator should be wearing an anti-static wristband, grounded at the same points as the

anti-static mat.

After removing the mainboard from its original packing, only place it on a grounded, anti-

static surface component side up. Immediately inspect the board for damage. Due to shifting

during shipping, it is suggested that the installer press down on all of the socket IC‘s to

ensure they are properly seated. Do this only with the board placed on a firm flat surface.

During configuration and installation, touch a grounded surface frequently to discharge any

static electrical charge that may have built up in your body. The best precaution is to wear a

grounded wrist strap. When handling the mainboard or an adapter card avoid touching its

components. Handle the mainboard and adapter cards either by the edges or by the adapter

card’s case mounting bracket.

The information presented in this publication has been carefully screened for reliability. The

manufacturer provides this manual “As is” with no warranties of any kind, either expressed

or implied, including but not limited to the implied warranties or conditions of this product’s

fitness for any particular purpose. In no event shall the manufacturer be liable for any loss of

profits, loss of business, loss of data, interruption of business, or indirect, special, incidental,

or consequential damages of any kind, even if the manufacturer has been advised of the

possibility of such damages arising from any defect or error in this manual or product.

The manufacturer has the right to change this specification without pre-notice.

Trademarks and product names appearing in this manual are may or may not be registered

with their respective holders.

SQ578

Table of Contents

1INTRODUCTION......................................................................................1-1

1.1 OVERVIEW ............................................................................................1-1

1.2 HOW TO USE THIS MANUAL....................................................................1-1

1.3 ITEM CHECKLIST....................................................................................1-2

2KEY FEATURES.......................................................................................2-1

2.1 PRODUCT SPECIFICATION......................................................................2-1

2.2 MAINBOARD LAYOUT..............................................................................2-2

3INSTALLATION PREVIEW....................................................................3-1

3.1 JUMPER SETTINGS ................................................................................3-1

3.2 INSTALLATION OF DRAM MODULES (SIMM OR DIMM).........................3-9

3.3 INSTALLATION OF THE CPU.................................................................3-12

3.4 INSTALLATION OF EXPANSION SLOTS...................................................3-13

3.5 INSTALLATION OF IDE, I/O CABLES CONNECTION ................................3-13

4BIOS SETUP..............................................................................................4-1

4.1 STARTING SETUP ..................................................................................4-1

4.2 MAIN SETUP MENU................................................................................4-3

4.3 STANDARD CMOS SETUP MENU..........................................................4-4

4.4 BIOS FEATURES SETUP MENU.............................................................4-8

4.5 CHIPSET FEATURES SETUP MENU.......................................................4-12

4.6 POWER MANAGEMENT SETUP MENU ..................................................4-14

4.7 PCI / PLUG AND PLAY SETUP..............................................................4-17

4.8 PERIPHERAL SETUP.............................................................................4-21

4.9 AUTO-DETECT HARD DISKS ................................................................4-23

4.10 SUPERVISOR PASSWORD SETTING .....................................................4-24

4.11 AUTO CONFIGURATION WITH OPTIMAL SETTINGS................................4-24

5VGA INSTALLATION(OPTION)............................................................5-1

5.1 INTRODUCTION......................................................................................5-1

5.2 SOFTWARE SUPPORT...............................................................................5-4

SQ578

1Introduction

1.1 Overview

The SQ578 mainboard integrates the Pentium microprocessor, memory, and I/O technologies

and is designed to fit into a standard AT form factor chassis. The design supports Pentium

processors, Pentium processors with MMX technology, Cyrix 6X86/6X86L/MX Processors,

IDT-C6 Processors, and AMD K5/K6 Processors. Page 2-2 illustrates the mechanical form

factor for the SQ578 mainboard.

1.2 How to use this Manual

This manual provides information necessary to install and operate the SQ578 mainboard and

is organized into five chapters. The purpose of this manual is to explain the installation

procedures and operations of the mainboard as specified below.

1. Introduction Manual information and checklist

2. Key Features An overview specification of this mainboard

3. Installation Preview Instructions on how to setup the mainboard

4. BIOS Setup BIOS software setup information

5. VGA Installation (Option) On Board VGA Feature information

SQ578

1.3 Item Checklist

The SQ578 mainboard should contain following items (ü). Immediately, contact your

retailer if you discover any missing items, or any damage.

þThe SQ578 mainboard

þThis SQ578 user‘s manual

þ1 IDE ribbon cable

þ1 floppy ribbon cable

þ1 parallel ribbbon cable and PS/2 mouse cable with mounting bracket

þ2 serial ribbbon cable attached to a mounting bracket

o1 VGA ribbon cable attached to a mounting bracket(optional)

qUSB (2 port) cable with bracket (optional)

qInfrared (IrDA) module with ribbon cable (optional)

SQ578

2Key Features

2.1 Product Specification

²Processor: Supports 75-300MHz Pentium family: Intel P54C, Pentium Processors

with MMX Technology (P55C), AMD-K5, AMD-K6 Cyrix 6X86, 6X86L, 6X86MX

and IDT-C6 Processors. The ZIF Socket 7 will support future Pentium Overdrives.

²L2 Cache: Onboard 256KB or 512KB Pipeline Burst SRAM

²SIMM (System Memory): Supports 70ns or faster Extended Data Output (EDO) or

Fast Page (FP) SIMM in four 72-pin SIMM sockets using 4MB, 8MB, 16MB, 32MB

or 64MB for a maximum of 256MB system memory.

²DIMM (System Memory):Supports 66MHz or faster unbuffer 2 or 4 clock 3.3V

DIMM in two 168-pin DIMM sockets using 8, 16, 32, 64 or 128 for a maximum of

256MB system memory.

²Chipset: Features SiS 5598 Pentium Single chip Integrated VGA or SiS 5582

Pentium Single chip without VGA, with a Winbond 83877F/TF super I/O controller

chip.

²Super VGA(option): To provide a compact video and graphics solution for PC based

system, high performance 3-in-1 PCI true-color graphics accelerator with video

accelerate functions, supports DCI Drivers and Direct Draw 3D Drivers, video

overlay for any graphic modes. Real-Magic MPEG API compatible. Supports DDC1

And DDC2B specifications.

²Expansion Slots:Three 32-bit PCI and Four 16-bit ISA expansions slots.

²Super Multi-I/O:Two high-speed UART compatible serial ports and One parallel

port with ECP and EPP compatibility. One FDD header supporting either 5.25“ or 3.5”

(1.2 or 1.44/2.88MB) floppy drives. One IrDA TX/RX infrared port.

²Keyboard and PS/2 Mouse: Onboard Standard AT Keyboard and PS/2 Mouse Port

²PCI bus Master IDE Controller:Onboard dual-channel PCI Bus Master IDE

support 4 IDE devices. This controller supports PIO Mode 3 and Mode 4 with a data

transfer rate up to 17MB per second. An Ultra DMA 33 (UDMA) supports data

transfer rates up to 33 MB per second. Also supports LS120 Floppy Drive.

²Universal Serial Bus (USB):Two standard USB interface supports up to 48MHz and

127 peripheral devices.

²PCI BIOS:Win 95 Plug and Play with Green power saving support, APM 1.2 and

DMI Support.

²Mechanical: Baby AT form factor 220 mm x 270 mm.

SQ578

2.2 Mainboard Layout

16-bit ISA Slot

Floppy Drive Conn.

Secondary IDE Conn

Primary IDE Conn

ZIF Socket 7

Flash BIOS

5598

5582

32-bit PCI Slot

DIMM Socket 2

DIMM Socket 1

SIMM Socket 4

SIMM Socket 3

SIMM Socket 2

SIMM Socket 1

Power Conn

COM2

COM1

KBD

(J1)

PS/2 MOUSE

JP1

J29

J30

J34

JP18

JP2 JP3

JP15

JP16

32K/64K*32

JP17

W83877F

/TF (J6)

USB

KEYLOCK

PWR LED

SPEAKER

HDD LED

J33

GR LED

RESET

J32

EXT SMI

JP10

JP11

JP12

JP13

JP14

JP4

JP5

JP6

JP7

JP8

JP9

J31

SQ578 3-1

3Installation Preview

Before you install the SQ578 mainboard into the system chassis you may find it convenient

to first configure the mainboard hardware. This section describes how to configure the

jumper settings, install memory modules, and how to attach the various system components.

Before using your computer you must review the following 7 steps:

1. Jumper settings

2. Installation of DRAM modules (SIMM or DIMM)

3. Installation of the CPU

4. Installation of expansion cards

5. Installation of IDE, I/O, VGA cables(Option) connection., and Power Supply connection

6. Installation of the Power Core to the System.

7. Setup of the system BIOS software

WARNING: When handling the system upgrade or plug in additional Add-On Card, please

be sure your System is Power Off.

3.1 Jumper Settings

You can configure the hardware options by setting jumpers on the mainboard. A jumper is a

set of two or more metal pins in a plastic base attached to the mainboard. A plastic “jumper

cap” with a metal (conductive) plate inside fits over two pins to create an electrical contact

or short between them. This contact establishes a hardware setting and is referred to as a

“closed” jumper setting.

Some jumper have two pins while others may have three or more. Jumpers are sometimes

combined into sets called jumper blocks where all the jumpers in the block must be set

together to establish a hardware setting. In this manual, the jumper settings will be

described graphically using a triangle (s) always marking pin 1. Those jumpers with two

pins will be shown as closed or open. A jumper is closed by placing the plastic jumper cap

over the two jumper pins and is opened by removing the jumper cap. Some jumpers are

oriented vertically and others horizontally with pin 1 marked as (s=P1).

SQ578

3-2

3.1.1 Jumpers, Jumper caps and Jumper blocks

Jumper cap 2-pin jumper 3-pin jumper Jumper block

3.1.2 Setting 3-pin jumpers

Jumper Pins 1 & 2 are closed with a jumper cap

Jumper Pins 2 & 3 are closed with a jumper cap

3.1.3 Setting 2-pin jumpers

This jumper is closed with the jumper cap placed over 2 pins

This jumper is open with the jumper cap removed from the 2 pins

WARNING: Some pins are used for connectors or power sources. These are clearly marked

separately from the jumpers listed in “Mainboard Layout”. Any improper placing of jumper

caps over these connectors will result in damage to your mainboard

3.1.4 Configuration Jumpers

Jumpers

1) JP10, JP11, JP12, JP13, JP14, JP15, JP16 Processor voltage selection

2) JP4, JP5, JP6, JP7, JP8,JP9 Processor/System speed setting

3) JP1 CMOS Selection

4) JP3,JP17(Option) On board VGA Selection

5) JP18 CYRIX LINEAR BURST MODE

Selection

6) JP2 DIMM Vlotage Selection

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Pentium Carte mère

Pentium

Pentium 82430 VX/P54C Manuel d'utilisation et d'entretien

Pentium

Pentium GA - 586IP Manuel utilisateur

Pentium

Pentium IN530 Manuel utilisateur

Pentium

Pentium GA-8IDML Series Manuel utilisateur

Pentium

Pentium P55-IT Manuel utilisateur

Pentium

Pentium P51437P4/FMB Manuel utilisateur

Pentium

Pentium GA-8SIML Manuel utilisateur

Pentium

Pentium 6EA Manuel utilisateur

Pentium

Pentium GA - 586ATV Manuel utilisateur

Pentium

Pentium 5VD2 Manuel d'utilisation et d'entretien

Pentium

Pentium P51430VX-280DM Explorer III Manuel utilisateur

Pentium

Pentium GA - 586AL Manuel utilisateur

Pentium

Pentium P51430TX-250 Manuel utilisateur

Pentium

Pentium Explorer IV Manuel utilisateur

Pentium

Pentium P5V580 VP3 Advance II Manuel utilisateur

Pentium

Pentium 5VC2 Manuel d'utilisation et d'entretien

Pentium

Pentium 5VM2 Manuel d'utilisation et d'entretien

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur