PEERLESS SmartMount SA740P Mode d’emploi

Max Load Capacity: 80 lb (36.3 kg)

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 05-18-05 SHEET #: 095-9234-4 08-23-05

Installation and Assembly:

Articulating LCD Wall Arm

Models: SA740P, SA740P-S, RTFPA-220, RTFPA-220S

Features:

•Fits 22" - 37" LCD screens

• Threetensionablepivotpointsforextensiveadjustmentofviewingangle

• VESA®100/200/200 x 200 compatible

• Frees up space by folding flat against the wall

• Keeps electronic wires routed internal to reduce clutter

2 of 27 ISSUED: 05-18-05 SHEET #: 095-9234-4 08-23-05

Note: Read entire instruction sheet before you start installation and assembly.

Forcustomercare call (800) 729-0307 or (708) 865-8870.

Table of Contents

Parts List.............................................................................................................................................................................. 3

Installation to Wood Stud Wall ............................................................................................................................................. 4

Installation to Solid Concrete and Cinder Block .................................................................................................................... 5

Tools Needed for Assembly

• studfinder ("edge to edge" studfinder is recommended)

• phillipsscrewdriver

• drill with 1/4" and 5/32" drill bits

Accessories

• Metal Stud Wall Plate (WSPmodels) (Not evaluated by UL)

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call

Peerless customer service at 1-800-729-0307.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never mount this product to a metal stud wall construction unless the stud can be verified to be constructed of 25

gauge steel minimum, the drywall is 1/2" thick minimum and you obtain and use the Peerless accessory kit for metal

studs.

• NeverexceedtheMaximumLoadCapacity.

• If mounting to wood wall stud wall construction, make sure that mounting screws are anchored into the center of the

studs. Use of an "edge to edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power. See suggested torque values where applicable within these instructions.

WARNING

3 of 27 ISSUED: 05-18-05 SHEET #: 095-9234-4 08-23-05

RTFPA-220 RTFPA-220S

SA740P SA740P-S

Description Qty. Part # Part #

Awall mount 1 095-0344 095-0345

BAlligator® anchor 2 590-0097 590-0097

C.198" ID x .313" OD x .437" H retaining spacer 4 590-5005 590-5003

D3/16" allen wrench 1 560-9713 560-9713

EM4 x .7 x 12 mm phillips screw 4 504-9013 504-2013

FM4 x .7 x 20 mm phillips screw 4 504-9020 504-2014

GM6 x 1 x 12 mm phillips screw 4 520-1128 520-2039

H#14 x 2-1/2" flat head wood screw 2 520-1202 520-2165

I1/4-20 x .5" flat head phillips screw 2 520-1209 520-2178

JM6 x 1 x 20 mm phillips screw 4 520-9402 520-2040

KM6 x 1 x 30 mm phillips screw 4 510-9109 520-2042

Parts List

CFG

4 of 27 ISSUED: 05-18-05 SHEET #: 095-9234-4 08-23-05

Installation to Wood Stud Wall

Remove cord covers from wall arm assembly (A) as shown in figure 1.1. Using a stud finder, locate and mark the

edges of the wood stud used in mounting this product. Use of an edge to edge stud finder is highly recommended.

Use a level to draw a vertical line down the center of the stud. Use wall plate as template to mark center of holes

along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (65 mm) deep.Attach wall mount (A) to wall using two

#14 x 2.5" flat head wood screws (H) as shown in figure 1.2.

Skip to step 2 on page 6.

• Makesurethatthewallwillsafelysupportthecombinedloadoftheequipmentandallattachedhardwareandcomponents.

WARNING

• Tightenscrews so that wall plateis firmly attached, but donot overtighten. Overtightening can damagethe screws,

greatlyreducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is

highlyrecommended.

WARNING

WOOD

STUD

WALL

CORDCOVER

fig. 1.1

fig. 1.2

5 of 27 ISSUED: 05-18-05 SHEET #: 095-9234-4 08-23-05

Installation to Solid Concrete and Cinder Block

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifications.

It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid

breakingoutthe back of the hole when enteringavoidor cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Makesure that the supporting surfacewill safely support the combinedload of the equipment andall attached hard-

wareand components.

WARNING

Removecord covers from wall arm assembly (A)as

shown in figure 1.1. Level and use wall plate as

template to mark center of holes. Drill two 1/4" (6

mm) dia. hole to a minimum depth of 2" (51 mm).

Insert anchors (B) in holes flush with wall as shown

in fig 1.3. Place wall mount (A) over anchor and

secure with wood screw (H) as shown in figures 1.4

and 1.6. Make sure wall mount is level, and tighten

all fasteners. See figure 1.5.

Skip to step 2 on next page.

• Concreteanchors are notintended for attachment to

concretewallcoveredwith a layer of plaster,drywall,

orotherfinishingmaterialasshownbelow.If mounting

toconcretewallcovered with plaster/drywall is

unavoidable,plaster/drywall(up to 5/8" thick) must be

counterboredasshownbelow.Be sure concrete

anchorsdonotpullaway from concrete when tighten-

ing screws. If plaster/drywall is thicker than

5/8", custom fasteners must be supplied by installer.

WARNING

concrete

wall

Drill holes

and insert

anchors.

Place wall

plate over

anchor and

secure with

screw.

Tighten all

fasteners.

WALLPLATE

fig. 1.3

fig. 1.4

fig. 1.5

CUTAWAYVIEW

CORRECT

concrete

plaster/

drywall

INCORRECT

concrete

plaster/

drywall

• Tighten screws so that wall plate is firmly attached,

butdo not overtighten. Overtightening candamagethe

screws,greatlyreducingtheir holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

fig. 1.6

WALLPLATE

6 of 27 ISSUED: 05-18-05 SHEET #: 095-9234-4 08-23-05

To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place

screen face side down. Find the VESA®hole pattern (VESA 200 can be horizontal or vertical) as shown in figures 2.1

through 2.3, and attach adapter plate to screen accordingly. Verify that all holes are properly aligned, and then

tighten screws using security allen wrench (D). For additional screen compatibility please refer to the LCD interface

list on our website www.peerlessmounts.com or call customer care for a screen specific adapter plate (LC mod-

els).

• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not

tightly secured, damage may occur to screen or product may fail. Contact customer care for correct hardware to use.

WARNING

fig. 2.1 fig. 2.2 fig. 2.3

VESA 100 VESA 200 VESA 200 x 200

Note: To add security, orderACC 919 for security screws. Refer toACC 919 instruction sheet for installing security screws.

7 of 27 ISSUED: 05-18-05 SHEET #: 095-9234-4 08-23-05

SCREW

fig. 2.5

ADAPTERPLATE

FORVESA100MOUNTINGPATTERN:

Thread two M4 x 12 mm screws (E), leaving .25" exposed thread, into top holes on back of screen. Hook screen onto

adapter plate, and attach using bottom two M4 x 12 mm screws as shown in figures 2.4 and 2.5. Tighten all four screws.

*Note: If screw (E) gets less than three threads of engagement, attach adapter plate to back of screen using four M4 x 20

mm screws (F) as indicated in figure 2.5.

FORVESA200MOUNTINGPATTERN:

Thread two M4 x 12 mm screws (E), leaving .25" exposed thread, into top holes on back of screen. Hook screen onto

adapter plate, and attach using two bottom M4 x 12 mm screws as shown in figures 2.4 and 2.5. Tighten all four screws.

*Note: If screw (E) gets less than three threads of engagement, attach adapter plate to back of screen using four M4 x 20

mm screws (F) as indicated in figure 2.5.

FORVESA200x200MOUNTINGPATTERN:

Thread two M6 x 12 mm screws (G), leaving .25" exposed thread, into top holes on back of screen. Hook screen onto

adapter plate, and attach using two bottom M6 x 12 mm screws as shown in figures 2.4 and 2.5. Tighten all four screws.

FOR SHARP™37"LCD SCREEN MODELS LC-37HV6UAND LC-37HV4U:

Thread two M6 x 20 mm screws (J), leaving .25" exposed thread, into top holes on back of screen. Hook screen onto

adapter plate, and attach using two bottom M6 x 20 mm screws as shown in figures 2.4 and 2.5. Tighten all four screws.

FOR SHARP™45" LCD SCREEN MODEL LC-45GX6U:

Thread two M6 x 30 mm screws (K), leaving .25" exposed thread, into top holes on back of screen. Hook screen onto

adapter plate, and attach using two bottom M6 x 30 mm screws as shown in figures 2.4 and 2.5. Tighten all four screws.

*For screens with a hole

pattern in a pocket,

spacers (C) go between

adapter plate and screen.

SCREW

ADAPTER

PLATE

fig. 2.4

8 of 27 ISSUED: 05-18-05 SHEET #: 095-9234-4 08-23-05

3Adjust tension knob on side of mount shown in figure

3 to desired tension to balance your screen size and

weight.

Push or pull from top or bottom of screen to adjust

tilt as shown. The tilt can be adjusted to a maximum

of15°forwardor5°backward.

• Becarefulnottopinchfingerswhenopeningand

closing mount from the wall.

CAUTION

• Do not tighten screws with excessive force.

Overtighteningcan cause damage to mount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION TENSIONKNOB

Note: Makesurecords have enough slack to allow full movementofthearm.

Route cords inside arm slots of wall mount (A) as shown in figure 4.1. Optional: Run power cord through one side of

mountandsignalcable(s)through other side in order to avoid interference with the signal.

Lock cords into place by sliding cord covers (I) onto mount as shown in figure 4.2. Screen may have to be moved for

better access for sliding on the cord covers.

fig. 4.1

fig. 4.2

fig. 3

9 of 27 ISSUED: 05-18-05 SHEET #: 095-9234-4 08-23-05

If more or less tension is desired in the arm pivot points, do the following:

• To increase tension, turn tension screw(s) clockwise with 3/16" allen wrench (D).

• To reduce tension, turn tension screw(s) counter-clockwise with allen wrench. Do not turn more than half a turn.

PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

TENSIONSCREWS

• Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the

screen to fall.

WARNING

Capacité de charge maximale :

36,3 kg (80 lb)

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 05-18-05 SHEET #: 095-9234-4 08-23-05

Installation et assemblage :

Bras mural articulé pour écran à cristaux liquides

Modèles : SA740P, SA740P-S, RTFPA-220, RTFPA-220S

Caractéristiques :

•Convient aux écrans à cristaux liquides de 55 à 92,5 cm (22 à 37 po)

• Troispointsdepivotementpouvantêtre tensionnés pour permettre un réglage

étendudel’angle visuel

• Compatibleavecla configuration VESA®100/200/200 x 200

• Donne plus d’espace en se repliant à plat contre le mur

• Maintient les fils des fonctions électroniques à l’intérieur afin de réduire

l’encombrement

Autres manuels pour SmartMount SA740P

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels PEERLESS Support TV

PEERLESS

PEERLESS PARAMOUNT PT660 Manuel utilisateur

PEERLESS

PEERLESS Paramount PP730 and assembly Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PA740 Mode d’emploi

PEERLESS

PEERLESS Smartmount ST650 and assembly Mode d’emploi

PEERLESS

PEERLESS Peerless OneMount Flat Panel Modular Wall Mount... Mode d’emploi

PEERLESS

PEERLESS SUF640P and assembly Mode d’emploi

PEERLESS

PEERLESS SMART MOUNT SF 16D and assembly Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PT632 and assembly Mode d’emploi

PEERLESS

PEERLESS LWS310/BK Mode d’emploi

PEERLESS

PEERLESS Smartmount ST630P and assembly Mode d’emploi

PEERLESS

PEERLESS SMARTMOUNT SF 635P Mode d’emploi

PEERLESS

PEERLESS SmartMount SF670 and assembly Mode d’emploi

PEERLESS

PEERLESS MIS374A Mode d’emploi

PEERLESS

PEERLESS HAVE1 FPZ-655 Manuel utilisateur

PEERLESS

PEERLESS Smartmount ST632P Mode d’emploi

PEERLESS

PEERLESS FLD-UNV Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PF640 and assembly Manuel utilisateur

PEERLESS

PEERLESS Designer Series Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PP740 Mode d’emploi

PEERLESS

PEERLESS PLA 60 and assembly Mode d’emploi

PEERLESS

PEERLESS ACC324 Mode d’emploi

PEERLESS

PEERLESS VML11 Mode d’emploi

PEERLESS

PEERLESS SUA746PU Mode d’emploi

PEERLESS

PEERLESS PM 13 and assembly Mode d’emploi

Manuels Support TV populaires d'autres marques

Ergotron

Ergotron Neo Flex Cantilever UHD Manuel utilisateur

StarTech.com

StarTech.com FPCEILBTB Manuel utilisateur

VonHaus

VonHaus 05/038 Manuel utilisateur

Techlink

Techlink ECHO TV Manuel utilisateur

Sandstrom

Sandstrom SSTVMC12X Manuel utilisateur

Sony

Sony SU-WL700 Mode d’emploi

ICW

ICW SCACC18 Manuel utilisateur

LG WM-L640V Manuel utilisateur

Gembird

Gembird WM-65ST-01 Manuel utilisateur

ERARD

ERARD FiTUP XXL 035320 Manuel utilisateur

Kanto

Kanto RCF180 Manuel utilisateur

GEM

GEM GEM GP001 Manuel utilisateur

Gladiator Joe

Gladiator Joe GJ0A0053 Manuel utilisateur

Vivotek

Vivotek AM-105 Manuel utilisateur

Vivo

Vivo VESA STAND-VAD1B Manuel utilisateur

AmazonBasics

AmazonBasics B07QG3LMG4 Manuel utilisateur

Secura

Secura QLF210 Manuel utilisateur

Marquant

Marquant 929-083 Mode d'emploi