Peerless-AV PRS-EXA Mode d’emploi

Installation and Assembly:

Projector Ceiling/Wall Mount

Installed to

Ceiling

Installed to Wall

(PRS-EXC models are not

wall mountable due to its

extensive reach)

Models: PRS-EXA, PRS-EXA-S, PRS-EXA-W

PRS-EXB, PRS-EXB-S, PRS-EXB-W

PRS-EXC, PRS-EXC-S, PRS-EXC-W

Features:

• Continuous channel design for uninterrupted drop length or wall extension adjustments

• Safety catch designed into extension to ensure user and equipment safety

• Internal cable management within channels for clean, clutter-free appearance

• Includes PRS Series projector mount for precise image alignment

Max UL Load Capacity:

25 lb (11.3 kg)

ISSUED: 04-24-08 SHEET #: 055-9256-9 11-21-11

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com

2 of 13 ISSUED: 04-24-08 SHEET #: 055-9256-9 11-21-11

NOTE: Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

•stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

•drill

•phillips screw driver

•5/16" bit for concrete and cinder block wall

•open end wrench

•5/32" bit for wood stud or joist

•level

•8 mm open end wrench

Table of Contents

Parts List............................................................................................................................................................................. 3-4

Installing Outer Channel to Ceiling Plate ...............................................................................................................................5

Installation to Wood Joist Ceiling or Wood Stud Wall.............................................................................................................6

Installation to Solid Concrete Ceiling or Concrete/Cinder Block Walls...................................................................................7

Installing Inner Channel and Routing Cables .........................................................................................................................8

Installing Projector Mount................................................................................................................................................. 9-10

Attaching Adapter Plate to Projector................................................................................................................................10-11

Projector Alignment ............................................................................................................................................................. 12

Adjusting Mount Extension.................................................................................................................................................. 13

Installing Cable Covers........................................................................................................................................................ 13

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood ceiling/wall studs, make sure that mounting screws are anchored into the center of the studs.

Use of an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

• Wood Beam Included

• Solid Concrete Included

• Cinder Block Included

• Brick Contact Customer Service (not evaluated by UL)

• Other or unsure? Contact Customer Service (not evaluated by UL)

WARNING

3 of 13 ISSUED: 04-24-08 SHEET #: 055-9256-9 11-21-11

extendable outer channel (BB) inner channel (CC) cable cover (LL)

Model# length part# part# part#

PRS-EXA 8.69" - 12.79" 055-1779 055-1778 055-1809-2

PRS-EXA-S 8.69" - 12.79" 055-4779 055-4778 055-4809-2

PRS-EXA-W 8.69" - 12.79" 055-2779 055-2778 055-2809-2

PRS-EXB 12.69" - 20.69" 055-1776 055-1775 055-1809-1

PRS-EXB-S 12.69" - 20.69" 055-4776 055-4775 055-4809-1

PRS-EXB-W 12.69" - 20.69" 055-2776 055-2775 055-2809-1

PRS-EXC 19.14" - 32.9" 055-1770 055-1769 055-1809

PRS-EXC-S 19.14" - 32.9" 055-4770 055-4769 055-4809

PRS-EXC-W 19.14" - 32.9" 055-2770 055-2769 055-2809

OUTER CHANNEL, INNER CHANNEL AND CABLE COVER

PART NUMBER CHART

Parts List PRS-EXA

PRS-EXB

PRS-EXA-S

PRS-EXB-S

PRS-EXA-W

PRS-EXB-W PRS-EXC PRS-EXC-S PRS-EXC-W

Description Qty. Part

Part

projector mount assembly 1 054-1174 054-4174 054-2174 054-1174 054-4174 054-2174

Badapter plate 1 055-1938 055-4938 055-2938 055-1938 055-4938 055-2938

C#14 x 2.5 phillips hex head wood screw 2 5S1-015-C03 5S1-015-C04 5S1-015-C04 5S1-015-C03 5S1-015-C04 5S1-015-C04

Dconcrete anchor 2 590-0320 590-0320 590-0320 590-0320 590-0320 590-0320

E#10-32 x 1/4" socket pin screw 1 520-1196 520-2196 520-2196 520-1196 520-2196 520-2196

F1/4" flat washer 6 540-1078 540-2078 540-2078 540-1078 540-2078 540-2078

GM3 x 8 mm socket pin serrated washer head screw 4 510-1004 510-2004 510-2004 510-1004 510-2004 510-2004

HM4 x 10 mm socket pin serrated washer head screw 4 510-1060 510-2060 510-2060 510-1060 510-2060 510-2060

IM5 x 10 mm socket pin serrated washer head screw 4 510-1126 510-2063 510-2063 510-1126 510-2063 510-2063

JM6 x 10 mm socket pin serrated washer head screw 4 510-1066 510-2066 510-2066 510-1066 510-2066 510-2066

#6 flat washer 4 540-1025 540-2025 540-2025 540-1025 540-2025 540-2025

L4 mm security t-wrench 1 560-1718 560-1718 560-1718 560-1718 560-1718 560-1718

M2 mm security allen wrench 1 560-1097 560-1097 560-1097 560-1097 560-1097 560-1097

ceiling plate 1 055-1773 055-4773 055-2773 055-1773 055-4773 055-2773

BB outer channel 1 SEE CHART SEE CHART SEE CHART SEE CHART SEE CHART SEE CHART

CC inner channel 1 SEE CHART SEE CHART SEE CHART SEE CHART SEE CHART SEE CHART

DD clamp plate 1 055-1771 055-4771 055-2771 055-1771 055-4771 055-2771

EE vertical mounting plate 1 055-1876 055-4876 055-2876 055-1876 055-4876 055-2876

FF horizontal mounting plate 1 055-1787 055-4787 055-2787 N/A N/A N/A

GG M5 x 16 mm socket pin screw 2 520-1161 520-2161 520-2161 520-1161 520-2161 520-2161

HH M6 x 12 mm socket pin screw 2 520-1050 520-2050 520-2050 520-1050 520-2050 520-2050

II M6 x 10 mm socket pin screw 4 520-1066 520-2066 520-2066 520-1066 520-2066 520-2066

JJ M5 x 10 mm socket pin screw 4 520-1063 520-2063 520-2063 520-1063 520-2063 520-2063

serrated locknut 2 530-1027 530-2042 530-2042 530-1027 530-2042 530-2042

LL cable cover 2 SEE CHART SEE CHART SEE CHART SEE CHART SEE CHART SEE CHART

Before you begin, make sure all parts shown are included with your product.

4 of 13 ISSUED: 04-24-08 SHEET #: 055-9256-9 11-21-11

CDEFGK

HI J

BB CC DD EE

FF HH II JJ KK

Parts may appear slightly different than illustrated.

5 of 13 ISSUED: 04-24-08 SHEET #: 055-9256-9 11-21-11

Install Outer Channel to Ceiling Plate

Attach outer channel (BB) to ceiling plate (AA) using four M6 x 10 mm socket pin screws (II) as shown. Tighten

screws with 4 mm security wrench (L).

6 of 13 ISSUED: 04-24-08 SHEET #: 055-9256-9 11-21-11

Installation to Wood Joist Ceilings or Wood Stud Walls

NOTE: Wall installation with models PRS-EXC, PRS-EXC-S and PRS-EXC-W is not available.

Use a stud ﬁnder to locate the edges of the stud or joist. Use of an edge-to-edge stud ﬁnder is highly

recommended. Based on its edges, draw a vertical line down the stud's or joist’s center. Place ceiling/wall plate

(AA) on wall or ceiling as a template, making sure that the two mounting slots are on the centerline.

For ceiling installation: Opening on outer channel (BB) indicates front of mount. Use the correct mounting slots

on the ceiling/wall plate depending on ceiling joist orientation as shown in ﬁgure 2.1 and ﬁgure 2.2. Mounting slots

on ceiling plate allow for 45° (±22.5) of rotation before securing to joist.

For wall installation: Opening on outer channel (BB) indicates top of mount.

Mark the center of the two mounting holes. Drill two 5/32" (4 mm) dia. holes 2-1/2" (64 mm) deep. Secure

ceiling/wall plate (AA) to wood stud or joist using two #14 x 2-1/2" wood screws (C) and two 1/4" washers (F)

as shown.

Skip to step 3

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that ceiling/wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage

the screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud or joist. The use of an "edge to edge" stud

ﬁnder is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs or

joists. Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

WARNING

OPENING ON OUTER

CHANNEL (BB) INDI-

CATES TOP OF MOUNT

ﬁg. 2.3

WOOD

JOIST

ﬁg. 2.2

OPENING ON OUTER CHANNEL (BB)

INDICATES FRONT OF MOUNT

WOOD STUD

ﬁg. 2.1

CEILING INSTALLATION WALL INSTALLATION

(EXCEPT FOR PRS-EXC MODELS)

MOUNTING

SLOTS ALLOW

FOR ROTA-

TION BEFORE

SECURING TO

JOIST

7 of 13 ISSUED: 04-24-08 SHEET #: 055-9256-9 11-21-11

Installation to Concrete Ceilings or Concrete/Cinder Block Walls

NOTE: Wall installation with models PRS-EXC,

PRS-EXC-S and PRS-EXC-W is not available.

Place ceiling/wall plate (AA) on ceiling or wall as a

template. NOTE: Place ceiling/wall plate according

to position of opening in outer channel (BB) as

shown in ﬁgure 2.4. or ﬁgure 2.5. Drill two 5/16"

(8 mm) dia. holes to a minimum depth of 2.5"

(64 mm). Attach ceiling/wall plate (AA) using two

concrete anchors (D), two #14 x 2.5" wood screws

Tighten wood screws (C) until ceiling/wall plate (AA)

is ﬁrmly attached.

CUTAWAY VIEW

INCORRECT

concrete

plaster/

drywall

CORRECT

concrete

plaster/

drywall

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 speciﬁca-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to

avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all at-

tached hardware and components.

BB AA

OPENING ON OUTER

CHANNEL (BB) INDICATES

FRONT OF MOUNT

CONCRETE

CEILING

CONCRETE

WALL

CINDER

BLOCK

WALL

OPENING ON OUTER

CHANNEL (BB)

INDICATES TOP OF

MOUNT

ﬁg. 2.4

ﬁg. 2.5

CEILING

INSTALLATION

WALL INSTALLATION

(EXCEPT FOR PRS-EXC MODELS)

ﬁg.

2.6 1

Drill holes and insert anchors (D).

Place plate (AA) over anchors (D) and secure with screws (C) and

washers (F).

Tighten all fasteners.

concrete

surface

WARNING

• Tighten wood screws ﬁrmly, but do not overtighten.

Overtightening can damage the screws, greatly

reducing their holding power.

• Never tighten in excess of 80 in • lb (9 N.M.).

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁnishing material. If mounting to concrete surfaces

covered with a ﬁnishing surface is unavoidable (not

evaluated by UL), the ﬁnishing surface must be

counterbored as shown below. Be sure concrete

anchors do not pull away from concrete when

tightening screws. If plaster/drywall is thicker than

5/8" (16 mm), custom fasteners must be supplied by

installer (not evaluated by UL).

WARNING

8 of 13 ISSUED: 04-24-08 SHEET #: 055-9256-9 11-21-11

Installing Inner Channel and Routing Cables

3NOTE: Be certain holes on inner channel (CC) face in the same direction of opening on outer channel (BB).

NOTE: Cables must be removed from projector before routing through channels. If cables are not removable from

projector, routing through channels is not an option.

Guide projector cables into openings in channels then insert inner channel (CC) into outer channel (BB) as shown

in ﬁgure 3.1 or 3.3.

Position inner channel (CC) to the desired extended position and secure using two M6 x 12 mm socket pin

screws (HH) through clamp plate (DD) and into inner channel (CC) as shown in ﬁgure 3.2 or 3.4.

CEILING INSTALLATION WALL INSTALLATION

(EXCEPT FOR PRS-EXC MODELS)

OPENING

HOLES

ﬁg. 3.4

ﬁg. 3.3

OPENING

HOLES

GUIDE

CABLES IN

CHANNELS

ﬁg. 3.1

ﬁg. 3.2

9 of 13 ISSUED: 04-24-08 SHEET #: 055-9256-9 11-21-11

Installing Projector Mount

4Installing PRS projector mount with wall installation: Position PRS projector mount (A) to the orientation shown

in ﬁgure 4.1 and attach to horizontal mounting plate (FF) using two M5 x 16 mm socket pin screws (GG), four ﬂat

washers (F) and two locknuts (KK).

Installing PRS projector mount with ceiling installation: Attach vertical mounting plate (EE) to PRS projector

mount (A) using two M5 x 16 mm socket pin screws (GG), four ﬂat washers (F) and two locknuts (KK) as shown in

ﬁgure 4.2.

NOTE: Placing washer (F) and nut (KK) combination on inside of PRS projector mount ﬁrst while attaching

mounting bracket (EE or FF) can make installation easier as shown in ﬁgure 4.3.

ﬁg. 4.1 ﬁg. 4.2

ﬁg. 4.3 PLACE WASHER (F) AND

NUT (KK) COMBINATION

FIRST

5Ceiling installation: Insert vertical mounting plate (EE) into inner channel (CC) with projector mount (A) in the

correct orientation shown in ﬁgure 5.1. Secure vertical mounting plate to inner channel using four socket pin screws

(JJ) as shown in ﬁgure 5.2.

ﬁg. 5.1

ARROW

INDICATES

FRONT OF

MOUNT

ﬁg. 5.2

ARROW INDICATES

FRONT OF MOUNT

CEILING INSTALLATION

WALL INSTALLATION

(EXCEPT FOR EXC MODELS)

ARROW INDICATES

FRONT OF MOUNT

10 of 13 ISSUED: 04-24-08 SHEET #: 055-9256-9 11-21-11

Wall installation: Insert horizontal mounting plate (FF) into inner channel (CC) as shown in ﬁgure 5.3. Secure

horizontal mounting plate to inner channel using four socket pin screws (JJ) as shown in ﬁgure 5.4.

ﬁg. 5.3

ARROW INDICATES

FRONT OF MOUNT

ﬁg. 5.4

JJ CC

NOTE: The projector you are installing may differ in appearance from the sample illustrated below.

Place projector upside down. Locate adapter plate (B) with notch facing forward as close to projector center of

gravity as possible without covering any mounting holes. Loosen channels with 4 mm security allen wrench (I),

and if there are only three mounting holes remove fourth channel. Using one channel for each mounting

hole, position feet of channels over mounting holes as shown below. IMPORTANT:: If projector does not have

at least three mounting holes, do not use this adapter plate.

NOTE: Some projectors have feet which can be removed and the corresponding threaded insert can be used

for a mounting hole.

NOTE: Once channels are in position retighten fasteners.

*Notch indicates front of projector.

Attaching Adapter Plate to Projector

GENERIC PROJECTOR

MOUNTING HOLE

CHANNEL

FOOT OF CHANNEL

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels peerless-AV Support et étagère

peerless-AV

peerless-AV ACC-MB08 Manuel utilisateur

peerless-AV

peerless-AV ACC976 Manuel utilisateur

peerless-AV

peerless-AV EXT Manuel utilisateur

peerless-AV

peerless-AV CMJ450 Mode d’emploi

peerless-AV

peerless-AV SS560F Manuel utilisateur

peerless-AV

peerless-AV DS-VW775-QR Manuel utilisateur

peerless-AV

peerless-AV DCS400 Manuel utilisateur

peerless-AV

peerless-AV PJR125-POR Manuel utilisateur

peerless-AV

peerless-AV MOD-AWM2 Manuel utilisateur

peerless-AV

peerless-AV WMJ018 Manuel utilisateur

peerless-AV

peerless-AV ACC973 Manuel utilisateur

peerless-AV

peerless-AV DS-VW655-2X2 Manuel utilisateur

peerless-AV

peerless-AV MOD-CPI2 Manuel utilisateur

peerless-AV

peerless-AV SA752PU Manuel utilisateur

peerless-AV

peerless-AV ACC310 Mode d’emploi

peerless-AV

peerless-AV DSF265P Manuel utilisateur

peerless-AV

peerless-AV KIL742 Manuel utilisateur

peerless-AV

peerless-AV SPL746 Manuel utilisateur

peerless-AV

peerless-AV SMARTMOUNT XT SFX660 Manuel utilisateur

peerless-AV

peerless-AV DSF210-GFC Manuel utilisateur

peerless-AV

peerless-AV MOD-ASC2 Manuel utilisateur

peerless-AV

peerless-AV EWL-OH55F Manuel utilisateur

peerless-AV

peerless-AV ST650-AB Manuel utilisateur

peerless-AV

peerless-AV Paramount PP740 Mode d’emploi

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur

peerless-AV PRS-EXA Mode d’emploi

Manuels Support et étagère populaires d'autres marques