Peerless-AV B-MIS38426 Manuel utilisateur

12019-08-26 #:090-9217-1

ENG

60 lb

(27 kg)

MAX

B-MIS38426

For Samsung Super Ultra Wide Curved Monitor

43": LC43J890DKNXZA

49": C49HG90DMN

49": LC49J890DKNXZA

22019-08-26 #:090-9217-1

Symbols

ENG

WARNING

ENG #

Skip to step.

ENG x3

Screws must get at least three

full turns and t snug.

ENG

Display center.

ENG

Do not overtighten screws.

ENG

Tools Needed for Assembly.

ENG

3/8"

(10mm)

ENG To properly tighten screws: Tighten until screw

head makes contact, then tighten another 1/2

turn. Do not overtighten screws.

+1/2

ENG - Before installing make sure the supporting surface will support the combined load of the equipment and

hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.

Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift

and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to

product failure or personal injury. Be careful not to pinch ngers when operating the mount. For support please

call customer care at 1-800-865-2112.

WARNING

Listen

ENG

17/64" 5/8", 7/16"

3/32" 2"-3"

32019-08-26 #:090-9217-1

A (1)

E (1)

desktop swivel base

support tube

Parts (Before beginning, make sure you have all parts shown below).

ENG

Parts List

Part #Description Qty

Adesktop swivel base 1 090-1821

Badaptor bracket 2 091-1211

Cright adaptor bracket 2 091-1217

Dleft adaptor bracket 2 091-1218

Esupport tube 1 091-1221

FM6 x 6mm hex set screw 2 510-9150

GM4 x 10mm socket pin screw 8 520-1060

Hslope nut 3 530-0035

I1/4-20 x 3/4" washer head screw 4 520-1321

J1/4" x 1/2" x .068 split washer 4 540-9402

K4mm allen wrench 1 560-9646

L48" foam strip 1 570-1170

M1/4-20 lock nut 4 530-1021

Nfender washer 4 540-1008

O1/4-20 x 3" threaded rod 4 520-2585

Pbase plate 1 090-1544

Qthrust washer 1 590-1287

R1/4-20 x 1.5" threaded rod 4 520-2250

S3mm allen wrench 1 560-0194

T10-32 x 1/2" set screw 2 520-1614

D (2)

C (2)

B (2)

adaptor bracket right adaptor bracket left adaptor bracket

L (1)

48" foam strip

K (1)

4mm allen wrench

J (4)

1/4" x 1/2" x .068 split washer

I (4)

1/4-20 x 3/4" washer

head screw

G (8)

M4 x 10mm socket pin

screw

F (2)

M6 x 6mm hex set

screw

S (1)

3mm allen wrench

42019-08-26 #:090-9217-1

Q (1)

thrust washer

H (3)

slope nut

P (1)

base plate

O (4)

1/4-20 x 3" threaded rod

N (4)

fender washer

M (4)

1/4-20 lock nut

R (4)

1/4-20 x 1.5" threaded rod

T (2)

10 x 32mm x 1/2"

hex set screw

52019-08-26 #:090-9217-1

ENG - Wooden mounting surface requires a minumum of 3/4" thickness to hold screen securely.

WARNING

Use base plate as a

template to mark location

of holes. Drill four holes in

square formation, aligned

to front of desk.

Threaded rods

must fasten a

minimum of three

turns.

ENG

22-1

O (4)

Drill 2" to 3" cord

managment hole in the

center of the square

formation.

1-1

Turn base

upside down.

ENG

ENG ENG

17/64"

OR R (4)

Front of desk

ENG Front of desk

ENG

2"-3"

62019-08-26 #:090-9217-1

60°

0°

120°

180°

210°

240°

30°

60°

0°

120°

180°

40°

240

240°

40°

210°

240°

40°

Swivel restriction: refer to detail 1 through 4. Fasten two set screws

where indicated below to the outside of desired angle in steel base.

Note: set screws must be bottomed out into base.

ENG

Front

ENG

3/32"

Detail 1

Detail 2

Detail 3

Detail 4

72019-08-26 #:090-9217-1

4-1

ENG - Make sure that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

WARNING

ENG - Installations to desktops that have a gap between two supporting boards are not acceptable mounting

surfaces for the desktop swivel mount.

CAUTION

M (4)

N (4)

Align plate with threaded rods.

Note: Washer must be centered.

ENG

Align base assembly with

supporting surface and base

pattern facing the front as

shown. Tighten four fender

washers with four lock nuts

in the sequenced pattern

at minimum ush with the

bottom of the threaded rods.

ENG

Front

ENG Front

ENG

7/16"

(11mm)

82019-08-26 #:090-9217-1

Bottom of desk

ENG

5-2

Bottom of desk

ENG Bottom of desk

ENG

Leave space

between

slope nuts.

ENG

Tightening

slope nut

ENG

Optional: for added security replace two of the

washers and locknuts with slope nuts. Hand

tighten slope nuts onto two of the threaded rods

until snug against bottom of desk as shown.

ENG

Insert an open end wrench

between both slope nuts and tighten as shown.

After top slope nut is secure remove bottom slope

nut as shown.

ENG

5-1

5-3

After slope nut is

secure, remove bottom

slope nut as shown.

ENG

5/8"

Thread another slope nut upside-down,

about two turns from rst slope nut as

shown. Avoid jamming both slope nuts

together, doing so may make it di󰀩cult

to remove slope nut used for tightening.

ENG

92019-08-26 #:090-9217-1

66-1

6-2

B (2)

J (4)

F(2)

3/8"

(10mm)

I (4)

10 2019-08-26 #:090-9217-1

Note orientation of tab

ENG

Bottom display

ENG

Top display

ENG

Note orientation of tab

ENG

7-1

Samsung Super Ultra Wide Curved Monitor

43" (LC43J890DKNXZA), 49" (C49HG90DMN), 49" (LC49J890DKNXZA)

sold separately

ENG

Table des matières

Autres manuels peerless-AV Support et étagère

peerless-AV

peerless-AV RMI2W Manuel utilisateur

peerless-AV

peerless-AV SPL724 Manuel utilisateur

peerless-AV

peerless-AV ACC310VWC4 Manuel utilisateur

peerless-AV

peerless-AV Paramount PF632 Manuel utilisateur

peerless-AV

peerless-AV MOD-FCS2KIT300 Manuel utilisateur

peerless-AV

peerless-AV DS-ACC770 Mode d’emploi

peerless-AV

peerless-AV KIP586-3LG-EUK Manuel utilisateur

peerless-AV

peerless-AV MOD-FPMD2 Manuel utilisateur

peerless-AV

peerless-AV MOD-FCSKIT300-B Manuel utilisateur

peerless-AV

peerless-AV TVA775 Manuel utilisateur

peerless-AV

peerless-AV MOD-FCSKIT300 Manuel utilisateur

peerless-AV

peerless-AV ACC 050 Manuel utilisateur

peerless-AV

peerless-AV SUT670P Manuel utilisateur

peerless-AV

peerless-AV SMARTMAUNT Series Manuel d'instructions

peerless-AV

peerless-AV SR598ML3 Manuel utilisateur

peerless-AV

peerless-AV PLA 60-UNL-S Mode d’emploi

peerless-AV

peerless-AV SMARTMOUNT Series Manuel d'instructions

peerless-AV

peerless-AV SS575K Manuel utilisateur

peerless-AV

peerless-AV IM760P Manuel utilisateur

peerless-AV

peerless-AV ACCXT400 Mode d’emploi

peerless-AV

peerless-AV ACC558 Manuel utilisateur

peerless-AV

peerless-AV SR598ML3T Manuel utilisateur

peerless-AV

peerless-AV 0735029322108 Manuel utilisateur

peerless-AV

peerless-AV DS-MBZ647L Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur

peerless-AV B-MIS38426 Manuel utilisateur

Manuels Support et étagère populaires d'autres marques