Pax Technology E600 Manuel utilisateur

E600 Integrated Smart Terminal

Note: Product images shown may be different than actual

product received.

PAX TECHNOLOGY INC.

1. Contents Checklist

Please check the components after unpacking. If any one of them is missing, or if there

is a page missing from the product manual,etc., please contact the dealer.

Name

Qty.

E600

AC Power Adapter

AC Power Cable

Product manual

Charging base with external ports

2. Product Description

Guest Display

30W-pixel Camera

Fingerprint (optional)

Fingerprint Indicator (optional)

Main Display

Magnetic Card/ IC Card Slot

5 mega-pixel camera

Light Sensor

Power Indicator

The Front View

Volume Buttons

USB

Anti-theft Hole

Speaker hole

The Right Side View

The Front Rubber Foot

Base Contact

Contraction Band

Battery Cover

The Rear Rubber Foot

The Rear View

Nameplate Sticker

SIM Card Slot

Bar Code Sticker

SD Card Slot

SIM Card Slot Diagram

Diagram for Opening the Printer Cover

3. Installation

Power on: Press and hold the Power button for three seconds until the main screen displays

normally.

Power off: Press and hold the Power button for three seconds until the shutdown menu

appears, tap “Shutdown”, and then “shutting...” appears. The terminal will be turned off after a

few seconds.

Swipe the magnetic stripe card: Place the magnetic stripe face down (keep the magnetic

stripe card perpendicular to the main display), swipe card through the magnetic card slot at a

constant speed.

IC Card: Place the IC chip face down, then insert the IC card into the card slot, and push it to

the end.

Contactless card: Put the contactless card on the center of the payment module screen.

Tear paper: Press the print paper downward along the cutter and tear it leftward or rightward

when getting close to the main display.

Charge: Insert the external adapter or the base to charge the device, the indicator lighting in

red means the device is charging; the indicator lighting in green means charging is completed;

the indicator flashing in red and green alternately meanscharging is abnormal.

Replace SIM card: Open the battery cover on the bottom of the machine,remove the battery,

and follow the prompt to insert/take out the SIM card.

Replace SD card:Open the battery cover on the bottom of the machine, remove the battery, and

follow the prompt to insert/take out the SD card.

4, Specification

Operating System: Android 7.1

CPU: Cortex A53Qaud-core, 1.4GHz

Memory: 1GB RAM + 8GB Flash Memory

Display: 8" inch, resolution:800*1280, multi-touch capacitive touch screen

Printer: 2" high-speed thermal printer, support 58*50mm print paper roll

Audio: Built-in speaker, support headphone output

Camera: Front camera, 5 mega-pixel, fixed-focus, high-speed code scanning

Rear camera,30W-pixel,fixed-focus, high-speed code scanning

L-Sensor (Ambient Light Sensor): Automatically adjust the backlight brightness of the main

display

Wireless Communication: Support WIFI, Bluetooth, 3G/4G

Positioning: Support GPS, Compass, Gingileo, GLONASS

Card Slots: SIM card slot

Micro SD card slot（maximum supports 128GB）

magnetic stripe card/IC card slot, using two-in-one（support MAG&ICC）

Magnetic Card Reader: Support track 1/2/3.

IC Card Reader: Conform to the standard of ISO7816, EMV2000 L1&L2, PBOC3.0

Contactless Card Reader: Compatible with ISO14443 Type A&B

Working Environment Temperature: 0℃～50℃(32℉～122℉)

R.H.: 10%～93%( non-condense)

Storage Environment Temperature:-20℃～70℃(-4℉～158℉)

R.H.:5％～95％ (non-condense)

5. Cautions of installation and usage

1）Avoid exposing the terminal in hot, humid,dusty or strong electromagnetic environment.

2）Do not violently vibrate, shake or beat the product.

3）Do not plug/unplug any units of the product when it is power on, otherwise it may

damage the internal circuit.

4）Do not maintain the terminal if you are non-professional

5）Before inserting the magnetic stripe/IC/contactless card, please check whether there is

any foreign object inside or surround the card slot , and if any , report to related personnel.

Caution

Risk of explosion if battery replaced by an incorrect type.

Dispose of used batteries according to the instructions.

Hereby, PAX Computer Technology (Shenzhen) Co., Ltd. declares that the radio equipment

type E600 is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet

address：http://www.pax.com.cn/ProductCE.aspx

Icon shows

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic

equipment (WEEE). This means that this product must be handled pursuant to European

directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the

environment.

User has the choice to give his product to a competent recycling organization or to the

retailer when he buys an new electrical or electronic equipment.

The symbol indicates DC voltage

FCC COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may

cause undesired operation.

Warning

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Caution

Any changes or modifications not expressly approved by

the manufacturer could void the user's authority to

operate this equipment.

Radiation Exposure

This device complies with FCC radiation exposure limits

for general environments.

INDUSTRY CANADA STATEMENT

This device complies with Industry Canada license-exempt RSS standard(s).Operation is subject

to the following two conditions:

this device may not cause interference, and

this device must accept any interference, including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:

1) l'appareil ne doit pas produire de brouillage, et

2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d'en compromettre le fonctionnement.

This device and its antenna(s) must not be co-located or operating in conjunction with any other

antenna or transmitter, except tested built-in radios.

Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une

autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées.

The Country Code Selection feature is disabled for products marketed in the US/Canada.

La fonction de sélection de l’indicatif du pays est désactivée pour les produits commercialisés aux

États-Unis et au Canada.

Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body.

PAX TECHNOLOGY LIMITED reserves

the right to change product technology

specifications without notifying.

PAX TECHNOLOGY LIMITED

Manufacturer: PAX Computer Technology (Shenzhen) Co.,Ltd.

Address:4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High-

Tech Industrial Park, Shenzhen, Guangdong, P.R.C.

Tel: 0755-86169630 Fax: 0755-86169634

Website: http://www.pax.com.cn

Responsible Party: PAX Technology Inc.

Address: 8880 Freedom Crossing Trail, Building 400, 3rd Floor,

Suite 300, Jacksonville, Florida 32256

T: 1-877-859-0099

Table des matières

Autres manuels Pax Technology Terminal tactile

Pax Technology

Pax Technology D180 Manuel utilisateur

Pax Technology

Pax Technology D170 Manuel utilisateur

Pax Technology

Pax Technology PX7A Manuel utilisateur

Pax Technology

Pax Technology PRIORITY A920 Manuel utilisateur

Pax Technology

Pax Technology D200 Manuel utilisateur

Pax Technology

Pax Technology D180RF Manuel utilisateur

Pax Technology

Pax Technology TSYS A920 Manuel utilisateur

Pax Technology

Pax Technology Smart Kiosk SK300 Manuel utilisateur

Pax Technology

Pax Technology TSYS A920 Manuel utilisateur

Pax Technology

Pax Technology Aries8 Manuel utilisateur

Pax Technology

Pax Technology IM20 Manuel utilisateur

Pax Technology

Pax Technology D220 Manuel utilisateur

Pax Technology

Pax Technology A35 Manuel utilisateur

Pax Technology

Pax Technology A80 Manuel utilisateur

Pax Technology

Pax Technology PAXPOS S80 Manuel utilisateur

Pax Technology

Pax Technology SK800 Manuel utilisateur

Pax Technology

Pax Technology X5 Manuel utilisateur

Pax Technology

Pax Technology SP20 Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur