Patton electronics SMARTNODE 4950 Manuel utilisateur

SmartNode 4950 Series

Multi-Port T1/E1/PRI VoIP

Enterprise Gateway Router

Quick Start Guide

Part Number: 07MSN4950-QS, Rev. B

Revised: February 7, 2012

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

WWW: www.patton.com

2SmartNode 4950 Series Quick Start Guide

• Do not open the device when the power cord is connected. For sys-

tems without a power switch and without an external power

adapter, line voltages are present within the device when the power

cord is connected.

• For devices with an external power adapter, the power adapter shall

be a listed Limited Power Source The mains outlet that is utilized to

power the device shall be within 10 feet (3 meters) of the device,

shall be easily accessible, and protected by a circuit breaker in compli-

ance with local regulatory requirements.

• For AC powered devices, ensure that the power cable used meets all

applicable standards for the country in which it is to be installed.

• For AC powered devices which have 3 conductor power plugs (L1, L2

& GND or Hot, Neutral & Safety/Protective Ground), the wall outlet

(or socket) must have an earth ground.

• For DC powered devices, ensure that the interconnecting cables are

rated for proper voltage, current, anticipated temperature, flammabil-

ity, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazardous voltages

present regardless of whether the device is powered ON or OFF.

PSTN relates to interfaces such as telephone lines, FXS, FXO, DSL,

xDSL, T1, E1, ISDN, Voice, etc. These are known as “hazardous net-

work voltages” and to avoid electric shock use caution when working

near these ports. When disconnecting cables for these ports, detach

the far end connection first.

•Do not work on the device or connect or disconnect cables during periods

of lightning activity.

In accordance with the requirements of council directive 2002/96/EC on

Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-

of-life you separate this product from other waste and scrap and deliver

to the WEEE collection system in your country for recycling.

This device contains no user serviceable parts. This device can only be

repaired by qualified service personnel.

WARNING

SmartNode 4950 Series Quick Start Guide 3

1.0 Power up the SmartNode

1. Insert the barrel type connector end of the AC power cord into the external power supply connector.

2. Insert the female end of the power cord into the internal power supply connector.

3. Verify that the AC power cord included with your router is compatible with local standards. If it is not, con-

tact Patton to replace it with a compatible power cord.

4. Connect the male end of the power cord to an appropriate power outlet.

5. Wait until the Power LED stops blinking and remains constantly lit. Now the SmartNode is ready

to configure.

2.0 Connecting the SmartNode to your laptop PC

Electrostatic Discharge (ESD) can damage equipment and impair electrical

circuitry. It occurs when electronic printed circuit cards are improperly

handled and can result in complete or intermittent failures. Do the follow-

ing to prevent ESD:

• Always follow ESD prevention procedures when removing and replac-

ing cards.

• Wear an ESD-preventive wrist strap, ensuring that it makes good

skin contact. Connect the clip to an unpainted surface of the chassis

frame to safely channel unwanted ESD voltages to ground.

• To properly guard against ESD damage and shocks, the wrist strap

and cord must operate effectively. If no wrist strap is available,

ground yourself by touching the metal part of the chassis.

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, flam-

mability, and mechanical serviceability.

CAUTION

4SmartNode 4950 Series Quick Start Guide

Figure 1. Connecting to the PC

1. Connect the PC’s Ethernet port to LAN (ETH 0/1) port of the SmartNode 4950. The SmartNode 4950

Series is equipped with Auto-MDX Ethernet ports, so you can use straight-through or cross-over Ethernet

cables for host or hub/switch connections. (See figure 1.)

2. The SmartNode comes with a built-in DHCP server to simplify configuration. Therefore, to automatically

configure the PC for IP connectivity to the SmartNode, configure the laptop PC for DHCP. The SmartNode

will provide the PC with an IP address. Note that only Full Duplex operation is supported. Use auto nego-

tiation for best results.

3. Check the connection to the SmartNode by executing the ping command from the PC command window

as follows:

ping 192.168.1.1

3.0 Configuring the desired IP address

3.1 Factory-default IP settings

The factory default configuration for the Ethernet interface IP addresses and netmasks are listed in table 1.

Both Ethernet interfaces are activated upon power-up. LAN interface ETH 0/1 (LAN) provides a default DHCP

server. The WAN interface uses DHCP client to get the IP address and netmask automatically from the

service provider.

If these addresses match with those of your network, go to section 4.0 “Connecting the SmartNode to the

network” on page 5. Otherwise, continue with the following sections to change the addresses and

network masks.

Table 1. Factory default IP address and network mask configuration

Item IP Addresss Network Mask

WAN interface Ethernet 0 (ETH 0/0) DHCP DHCP

LAN interface Ethernet 1 (ETH 0/1) 192.168.1.1 255.255.255.0

DHCP server address range (LAN) 192.168.1.10-192.168.1.99 255.255.255.0

LAN (connect to ETH 0/1)

Laptop PC

Ethernet

RS-232

Console

ETH0/0

ETH0/1

Reset

0/0

0/10/20/3

T1/E1

SmartNode 4950 Series Quick Start Guide 5

3.2 Login

1. To access the SmartNode, start the Telnet application on your PC. Type the default IP address into the

address field: 192.168.1.1. Accessing your SmartNode via a Telnet session displays the login screen.

Type the factory default login: administrator and leave the password empty. Press the Enter key after the

password prompt.

password:<Enter>

192.168.1.1>

2. After you log in, your SmartNode will be running in operator execution mode (indicated by > character in

the command line prompt). To enter configuration mode, use the commands enable and configure.

192.168.1.1>enable

192.168.1.1#configure

192.168.1.1(cfg)#

3.3 Changing the WAN IP address

1. To modify IP configuration settings, you must enter context IP mode. Enter the following command:

192.168.1.1(cfg)#context ip router

192.168.1.1(ctx-ip)[router]#

2. Now you can set your IP address and network mask for the interface ETH 0/0(WAN). In this example a

network 172.16.1.0/24 is assumed. The IP address in example is set to 172.16.1.99. (You should set it

to the IP address that the network provider has given you.)

Note The examples in this guide use a private IP network with the network address 172.16.1.0/24.

192.168.1.1(ctx-ip)[router]#interface WAN

192.168.1.1(if-ip)[WAN]#ipaddress 172.16.1.99 255.255.255.0

2002-10-29T00:09:40 : LOGINFO : Link down on interface WAN.

2002-10-29T00:09:40 : LOGINFO : Link up on interface WAN.

172.16.1.99(if-ip)[WAN]#

3. Copy this modified configuration to your new start-up configuration. This will store your changes in non-

volatile memory. On the next start-up the system will initialize itself using the modified configuration.

172.16.1.99 (if-ip)[WAN]#copy running-config startup-config

172.16.1.99 (if-ip)[WAN]#

The SmartNode can now be connected to your network.

4.0 Connecting the SmartNode to the network

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, flam-

mability, and mechanical serviceability.

CAUTION

6SmartNode 4950 Series Quick Start Guide

In general, the SmartNode will connect to the network via the WAN (ETH 0/0) port. This enables the SmartNode

to offer routing services to the PC hosts on LAN (ETH 0/1) port. The SmartNode 4950 Series provides an auto-

MDX feature for both Ethernet ports, so you can use a straight-through or cross-over cable to connect to a host or

a switch (see figure 2).

Figure 2. Connecting the SmartNode to the network

1. You can check the connection with the ping command from the SmartNode to another host on the

local LAN.

172.16.1.99(if-ip)[WAN]#ping <IP Address of the host>

Note If the WAN address is not set to DHCP, to ping a device outside your local LAN you must first configure

the default gateway. (For information on configuring the default gateway, refer to section “Set IP

addresses” in Appendix C, “Command Summary” of the SmartNode Series SmartWare Software Config-

uration Guide.)

5.0 Loading the configuration (optional)

Patton provides a collection of configuration templates on the support page at www.patton.com/smart-

node—one of which may be similar enough to your application that you can use it to speed up configuring the

SmartNode. Simply download the configuration note that matches your application to your PC. Adapt the config-

uration as described in the configuration note to your network (remember to modify the IP address) and copy

the modified configuration to a TFTP server. The SmartNode can now load its configuration from this server

Note If your application is unique and not covered by any of Patton’s configuration templates, you can man-

ually configure the SmartNode instead of loading a configuration file template. In that case, refer to the

SmartNode Series SmartWare Software Configuration Guide for information on configuring the SmartNode

device.

Straight-through wired or crossover cable

LAN (ETH 0/1)

LAN

WAN (ETH 0/0) Network

RS-232

Console

ETH0/0

ETH0/1

Reset

0/0

0/1

0/2

0/3

T1/E1

SmartNode 4950 Series Quick Start Guide 7

In this example we assume an TFTP server resides on the host with the IP address 172.16.1.11 and the configu-

ration file named SN.cfg resides in the root directory of the TFTP server.

172.16.1.99(if-ip)[WAN]#copy tftp://172.16.1.11/SN.cfg startup-

config

Download...100%

172.16.1.99(if-ip)[WAN]#

After you reboot the SmartNode the new startup configuration will become active.

172.16.1.99(if-ip)[WAN]#reload

Running configuration has been changed.

Do you want to copy the 'running-config' to the 'startup-config'?

Press 'yes' to store, 'no' to drop changes : no

Press 'yes' to restart, 'no' to cancel : yes

The system is going down

6.0 Additional Information

For detailed information about configuring and operating guidance, set up procedures, and troubleshooting,

refer to the SN4950 User Manual available online at www.patton.com/manuals/SN4950.pdf and the

SmartWare Software Configuration Guide available online at www.patton.com/smartnode.

When you issue the reload command, the SmartNode will ask if you want to copy the

running configuration to the startup configuration. Since you just downloaded a con-

figuration file to the startup configuration you must answer this question with NO.

Otherwise, the downloaded configuration will be overwritten and lost!

IMPORTANT

8SmartNode 4950 Series Quick Start Guide

A.0 Customer and Technical Support

Toll-Free VoIP support: call sip:support@patton.com with a VoIP SIP client

Online support: www.patton.com

E-mail support: suppor[email protected]—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)

B.0 Compliance Information

B.1 Compliance

EMC Compliance:

•

FCC Part 15, Class A

•

EN55022, Class A

•

EN55024

Safety Compliance:

•

UL60950-1/CSA C22.2 No. 60950-1

•

IEC/EN 60950-1

•

AS/NZS 60950-1

PSTN Regulatory Compliance:

•

FCC Part 68

•

CS-03

•

TBR 12 & 13 (E1)

•

AS/ACIF S016

•

AS/ACIF S038

•

AS/ACIF S043 (G.SHDSL card)

•

NZ ISDN Layer 3 Supplement

SmartNode 4950 Series Quick Start Guide 9

B.2 Radio and TV interference

The SmartNode router generates and uses radio frequency energy, and if not installed and used properly—that

is, in strict accordance with the manufacturer’s instructions—may cause interference to radio and television

reception. The SmartNode router have been tested and found to comply with the limits for a Class A computing

device in accordance with specifications in Subpart B of Part 15 of FCC rules, which are designed to provide rea-

sonable protection from such interference in a commercial installation. However, there is no guarantee that

interference will not occur in a particular installation. If the SmartNode router does cause interference to radio or

television reception, which can be determined by disconnecting the unit, the user is encouraged to try to correct

the interference by one or more of the following measures: moving the computing equipment away from the

receiver, re-orienting the receiving antenna and/or plugging the receiving equipment into a different AC outlet

(such that the computing equipment and receiver are on different branches).

B.3 FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of

this equipment is a label that contains—among other information—a product identifier in the format US:

AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone network must comply with the

applicable FCC Part 68 rules and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that

temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone com-

pany will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with

the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could

affect the operation of the equipment. If this happens the telephone company will provide advance notice in

order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If

the equipment is causing harm to the telephone network, the telephone company may request that you discon-

nect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser-

vice commission or corporation commission for information.

B.4 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con-

firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra-

tion was performed based on a Declaration of Conformity indicating that Industry Canada technical speci-

fications were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protective,

operational and safety requirements. The Department does not guarantee the equipment will operate to the

user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to

the facilities of the local telecommunications company. The equipment must also be installed using an acceptable

method of connection. In some cases, the company’s inside wiring associated with a single line individual service

may be extended by means of a certified connector assembly (telephone extension cord). The customer should

be aware that compliance with the above condition may not prevent degradation of service in some situations.

10 SmartNode 4950 Series Quick Start Guide

Repairs to some certified equipment should be made by an authorized maintenance facility designated by the

supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for

their own protection that the ground connections of the power utility, telephone lines and internal metallic water

pipe system, are connected together. This protection may be particularly important in rural areas.

B.5 EC Declaration of Conformity

(See section B.6 “EG-Konformitätserklärung” for German version.)

Product Description: SmartNode 4950 Series

This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws

of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition

of their conformity.

The signed Declaration of Conformity can be downloaded from www.patton.com/certifications/.

B.6 EG-Konformitätserklärung

(see section B.5 “EC Declaration of Conformity” for English version)

Produktbezeichnung: SmartNode 4950 Baureihe

Die bezeichneten Produkte stimmen in der von uns in Verkehr gebrachten Ausführung mit den Vorschriften fol-

gender Richtlinie überein:

R&TTE 1999/5/EG

Richtlinie des europäischen Parlaments und des Rates zur Angleichung der Rechtsvorschriften der

Mitgliedstaaten über Funkanlagen und Telekommunikations-Endeinrichtungen und die gegenseitige

Anerkennung ihrer Konformität.

Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von: www.patton.com/

certifications/.

The safety advice in the documentation accompanying the products shall be obeyed.

The conformity to the above directive is indicated by the CE sign on the device.

Die Sicherheitshinweise in der mitgelieferten Produktdokumentation sind zu beachten.

Die Konformität mit der oben erwähnten Richtlinie wird durch das CE-Zeichen auf dem

Gerät bestätigt.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Patton electronics Routeur réseau

Patton electronics

Patton electronics SL4020 Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4552 Manuel utilisateur

Patton electronics

Patton electronics SL4020 Manuel utilisateur

Patton electronics

Patton electronics Patton IPLink 2603 Manuel utilisateur

Patton electronics

Patton electronics 3224 Diamond Edge Manuel utilisateur

Patton electronics

Patton electronics SmartNode 07MSN5200-QS Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 1200 Manuel utilisateur

Patton electronics

Patton electronics 4020 Series Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4900 Manuel utilisateur

Patton electronics

Patton electronics 2124 Manuel utilisateur

Patton electronics

Patton electronics IM1/I4 Manuel utilisateur

Patton electronics

Patton electronics 2121 Manuel utilisateur

Patton electronics

Patton electronics 3060/V24 Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4960 Series Manuel utilisateur

Patton electronics

Patton electronics 4110 Series Manuel utilisateur

Patton electronics

Patton electronics 3210 Manuel utilisateur

Patton electronics

Patton electronics 2121 Manuel utilisateur

Patton electronics

Patton electronics OnSite 2884 Manuel utilisateur

Patton electronics

Patton electronics IpLink 2884 Manuel utilisateur

Patton electronics

Patton electronics 4520 Manuel utilisateur

Patton electronics

Patton electronics Patton IPLink 2635 Manuel utilisateur

Patton electronics

Patton electronics PASSERELLES ROUTEURS VOIP 455X Guide de configuration

Patton electronics

Patton electronics SmartNode 4900 Series Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4634 Series Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité