PASCO OS-9171 Manuel utilisateur

Instruction Sheet

Aligning the PASCO Model OS-9171 Laser with the

OS-9172 Alignment Bench

The Helium Neon Laser

The helium neon laser is a 0.5 mW, TEM00 mode laser,

providing randomly polarized light at a wavelength of 632.8

nm. The built-in power supply is regulated so the output has

minimum ripple and the intensity is stable to within ±2.5%.

A 15 minute warm up is required to reach full power, but the

power on start-up is greater than 0.35 mW. If you'd like

more technical specifications, and a detailed explanation of

laser operation, see the instruction manual that's included

with the laser.

Caution: This is a relatively safe, low power

laser. Nevertheless, we strongly recommend the

following precautions:

1. Never look into the laser beam, either directly, or

as it is reflected from a mirror.

2. Set up experiments so the laser is either above or

below eye level (for both sitting and standing

people).

To Set Up the Laser using the Laser Alignment

Bench:

The laser is most conveniently aligned using the laser

alignment bench, which can be joined to the optics bench

using the bench couplers. The procedure is as follows:

1. Place the optics bench and the laser alignment bench

end to end, as shown in Figure 1. Notice that only one

end of the laser alignment bench has holes for two

leveling screws. That is the end that joins to the optics

bench.

2. Remove the four leveling screws on the adjoining ends

of the two benches.

3. Use the 1/4-20, hex-head screws that are included with

the bench couplers to attach the couplers to the legs of

the benches, as shown. Do not yet tighten the screws.

4. Insert one of the leveling screws, rubber foot down,

through the threaded hole in each coupler.

Figure 1 Connecting the Laser Alignment Bench

Laser

alignment

bench

Top View of Bench Coupler

Bench coupler

Leveling Screw

and lock-nut

1/4 20

hex-head

screw

Optics

bench

Optics bench

012-01562C

9/91

$1.00

Bench coupler

(one each side)

Laser alignment bench

Leveling screw

scientific

012-01562C

5. By adjusting all five leveling screws (one on the laser

alignment bench, two on the optics bench, and two on

the bench couplers), align the two benches so they are in

a straight line. Use a meter stick or a long straight edge

on top of the benches to check vertical alignment, and

on the side of the bench to check horizontal alignment.

6. When the benches are aligned, tighten the lock-nuts on

all the leveling screws, and also tighten the four hex-

head screws. After tightening the screws, recheck the

alignment.

To Align the Laser (so the laser beam is coincident

with the optical axis of the bench):

1. Place a piece of masking tape or tape a piece of paper

over the square hole on the front of a component holder,

as in Figure 2. Make a small dot on the tape or paper, in

the center of the square hole (1-inch from the top of the

component shelf, and 1.5-inch from the edge of the

component holder).

2. Place the laser on the alignment bench, as in Figure 3.

Center the laser on the bench, and make sure it is

reasonably parallel with the bench.

3. Place the component holder on the optics bench, about

10 cm from the laser aperture. Make sure that the

component holder is flush against the alignment rail of

the bench. The dot on the tape now marks the optical

axis of the bench.

4. Turn on the laser, and move the aperture end of the laser

sideways, as needed, so that the laser beam falls on the

dot.

1.5"

Figure 2 Locating the Optical Axis

5. Move the component holder about 90 cm away from the

laser aperture. Again, be sure the edge of the compo-

nent holder is flush against the alignment rail of the

bench.

6. Without moving the aperture end of the laser, move the

rear end of the laser as needed to recenter the laser beam

on the dot. (You may also need to adjust the leveling

screws on the laser alignment bench in order to center

the laser beam vertically on the dot.)

7. Repeat steps 3 through 6 until the laser beam is aligned

with the dot for both positions of the component holder.

Alignment bench

Figure 3 Aligning the Laser

Tape

paper

Laser

Dot

Component

holder with

alignment dot

Optics bench

Ce manuel convient aux modèles suivants

Autres manuels PASCO Instrument de mesure

PASCO

PASCO OS-7053 Manuel utilisateur

PASCO

PASCO PASPORT PS-2230 Manuel utilisateur

PASCO

PASCO PS-3234 Manuel utilisateur

PASCO

PASCO PS-3321 Manuel utilisateur

PASCO

PASCO ES-9078A Manuel utilisateur

PASCO

PASCO PS-2136A Manuel utilisateur

PASCO

PASCO OS-8458B Manuel utilisateur

PASCO

PASCO Pasport PS-2152 Manuel utilisateur

PASCO

PASCO PASPORT PS-2152 Manuel utilisateur

PASCO

PASCO PS-3222 Manuel utilisateur

PASCO

PASCO ME-8598 Manuel utilisateur

PASCO

PASCO SF-9069 Manuel utilisateur

PASCO

PASCO PS-3518 Manuel utilisateur

PASCO

PASCO PS-3238 Manuel utilisateur

PASCO

PASCO PASPORT PS-2148 Manuel utilisateur

PASCO

PASCO Xplorer GLX Manuel de programmation

PASCO

PASCO EM-3556 Manuel utilisateur

PASCO

PASCO PS-3215 Manuel utilisateur

PASCO

PASCO OS-8526A Manuel utilisateur

PASCO

PASCO PASPort PS-2222 Manuel utilisateur

PASCO

PASCO OS-8516A Manuel utilisateur

PASCO

PASCO Wireless Smart Gate Manuel utilisateur

PASCO

PASCO PS-3515 Manuel utilisateur

PASCO

PASCO SF-9500A Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur