ParaBody 848101 Manuel utilisateur
848101 LAT OPTION
Part # 6826701 Revision: 5/26/99
1
ASSEMBLY INSTRUCTIONS
Please note:
Tools Required forAssembly
* Thank you for purchasing the Parabody 848101 LAT OPTION. Please read these instructions
thoroughly and keep them for future reference. This product must be assembled on a flat, level
surface to assure its proper function.
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure
2
NOTE:BOLTLENGTHISMEASURED FROMTHEUNDERSIDE OFTHEHEAD OFTHEBOLT.
BOLT LENGTH RULER:
We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at (800) 328-9714.
BoltLengthRuler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
WELCOMETOTHE WORLDOF Serious steel!
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
2. Do not allow minors or children to play on or around this equipment.
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at (800) 328-9714.
BOLT LENGTH
5. Consult a physician before beginning any exercise program.
IMPORTANT NOTES
3
PARTS LIST
PART #
6824303
6823703
6825403
6824103
6825502
6275302
6274402
6542402
6824801
3103102
3116201
6177001
6405201
6467001
6692601
6825101
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
QTY
1
1
1
1
1
1
1
2
2
4
6
2
4
2
3
1
PART #
3116001
6140701
3102501
3102802
3102502
3102801
3102933
3102903
3102922
3102935
3102910
3103801
3108102
6122703
6480301
6127701
DESCRIPTION
1-1/4”RUBBERBUMPER
1X1”GLIDE
3/8”WASHER
3/8”LOCKNUT
1/2”WASHER
1/2”LOCKNUT
3/8X2”BOLT
3/8X2-1/2”BOLT
3/8X2-3/4”BOLT
3/8X4-1/2”BOLT
1/2X3”BOLT
5/16”SNAPLINK
1/4”QUICKDISCONNECTLINK
3/8X3/8” SPACER
3/8”FLANGESPACER
3/8X1” SPACER
QTY
1
8
12
11
2
1
2
2
6
1
1
2
1
2
6
1
DESCRIPTION
BASE
UPRIGHT
STAND
CROSSBRACE
CARRIAGE
LATBAR
LOWROWBAR
3/16X1-3/4 X5-1/4” PLATE
CABLE
1X8”GRIP
3-1/2”PULLEY
2-1/2X5-1/2”NON-SKIDSTRIP
2”SQ.ENDCAP
2”SQ COVERCAP
3X2” END CAP
17-1/2”FOAMSTRIP
KEY
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
FIGURE 1
STEP 1:
• SECURELYassemblethe one3/8 X2-3/4” BOLT(25),two 3/8”WASHERS(19), andone3/8” LOCKNUT(20)to theSTAND (3)as
shownin FIGURE 1.
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• Assemble two 2” SQ. COVER CAPS (14) onto the ends of the STAND (3) as shown in FIGURE 1.
• Insert two 3 X 2” END CAP (15) into the ends of the BASE (1) as shown in FIGURE 2.
FIGURE 2
STEP2:
3/8X 2-3/4” 25 19
14
15
20
1
3
13
• Assemble one 2” SQ. END CAP(13) into the end of the STAND (3) as shown in FIGURE 1.
4
5
FIGURE 4
STEP3:
• Assemble one 17-1/2” FOAM STRIP (16) to the underside of the CROSS BRACE (4) as shown in FIGURE 3.
• Assembletwo 2-1/2X 5-1/2”NON-SKIDSTRIPS (12)tothe CROSSBRACE(4) asshown inFIGURE3.
FIGURE 3
STEP4:
• SECURELYattach one 1-1/4”SQ. RUBBERBUMPER (17)to theCARRIAGE (5)as shownin FIGURE4.
• Insert two 2” SQ. END CAPS (13) into the ends of the CROSS BRACE (4) as shown in FIGURE 3.
16
12
4
18
5
17
13
• Attach eight 1 X 1” GLIDES (18) to the ends the CARRIAGE (5) as shown in FIGURE 4 using the following steps:
• Thoroughly clean all surfaces where the 1 X 1” GLIDES (18) are to be attached.
• Remove the 1 X 1” GLIDES (18) from the paper backing and firmly apply them to all shown surfaces.
6
STEP5:
FIGURE 5
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• Slidethe CARRIAGE(5) over theUPRIGHT (2)as
shownin FIGURE 5.
• Assemble the STAND (3) to the UPRIGHT (2) as
shownin FIGURE 5.
1
3
5
2
• Assemble the BASE (1) to the UPRIGHT (2) as
shownin FIGURE 5.
STEP6:
FIGURE 6
• SECURELYassemble the BASE (1) to the UPRIGHT (2) using one 1/2 X 3” BOLT(27), two 1/2” WASHERS (21) (slide front washer
INSIDEoftube),and one 1/2”LOCKNUT (22). SeeFIGURE6.
• Insert one 3 X 2” END CAP (15) and one 2” SQ. END CAP (13) into the ends of the UPRIGHT (2) as shown in FIGURE 6.
• SECURELYassemble the CROSSBRACE (4)to the UPRIGHT(2)usingtwo 3/8X 2-3/4” BOLTS(25), two3/8”WASHERS (19),and two
3/8”LOCKNUTS(20).SeeFIGURE6. 7
27 1/2 X 3”
3/8 X2-3/4” 25
21
20
19
22
21
1
15
13
4
2
8
STEP7:
FIGURE 7
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• Route the CABLE (9) through the UPRIGHT (2) as shown in FIGURE 7.
• SECURELYassemblethree3-1/2”PULLEYS(11)into the slotsoftheUPRIGHT(2) using three 3/8X2-3/4”BOLTS (25), six 3/8”FLANGE
SPACERS(31), and three3/8”LOCK NUTS(20)as showninFIGURE 7.(NOTE:Makesurethecable isroutedoverallthepulleys.)
3/8 X2-3/4” 25
2
9
31
20
11
9
STEP8:
FIGURE 8
23 3/8 X 2”
19
19
20
9
8
29
2
5
• Place one 3-1/2” PULLEY (11) into the loop of the CABLE (9) below the second and third PULLEY of the UPRIGHT (2) as shown in
FIGURE8.
• LOOSELYassemble two3/16X 1-3/4X 5-1/4”PLATES(8) toeach sideofthe 3-1/2”PULLEY(11)usingone 3/8X 2”BOLT(23),
two3/8”WASHERS (19),andone 3/8” LOCKNUT(20). SeeFIGURE8.
• Attachthe CABLE(9)from theUPRIGHT (2)to the CARRIAGE(5)using one1/4”QUICK LINK(29)as showninFIGURE 8.(IMPOR-
TANT!SecurelytightenQUICKLINK.)
11
SECURELY
TIGHTEN!
10
STEP9:
FIGURE 9
23 3/8 X 2”
19
19
20
9
11
2
• Route the end of the second CABLE (9) through the slot on the UPRIGHT (2) then SECURELYassemble one 3-1/2” PULLEY(11) to
theUPRIGHT(2) using two3/8X2-1/2”BOLTS(24), two3/8X3/8”SPACERS(30),four 3/8”WASHERS(19), and two 3/8”LOCKNUTS
(20).(NOTE:TheCABLE(9)shouldberoutedbetweenthepulleyandtheretainingboltasshowninFIGURE9.)
• Loopthe CABLE(9)around one3-1/2” PULLEY (11)as showninFIGURE 9.
• LOOSELYassemblethe3-1/2”PULLEY(11)tothe3/16 X 1-3/4X5-1/4”PLATES(8)using one 3/8X2” BOLT(23),two3/8”WASHERS
(19),andone 3/8” LOCKNUT (20).See FIGURE9.
• SECURELYtighten the two3/8X 2”BOLTS(23) ofthe 3/16X1-3/4 X5-1/4”PLATES(8).
24 3/8 X 2-1/2”
20
19
30
11
0123456
1/2 1/2 1/2 1/2 1/2 1/2
8
Table des matières
Autres manuels ParaBody Équipement de fitness
ParaBody
ParaBody PBF 472 Manuel utilisateur
ParaBody
ParaBody 811 Instructions de montage
ParaBody
ParaBody 893104 Manuel utilisateur
ParaBody
ParaBody 883 Manuel utilisateur
ParaBody
ParaBody PBF005C Manuel utilisateur
ParaBody
ParaBody 874 Instructions de montage
ParaBody
ParaBody Free Weight Systems Manuel utilisateur
ParaBody
ParaBody 849 Manuel utilisateur
ParaBody
ParaBody 835102 Manuel utilisateur
ParaBody
ParaBody 870 Manuel utilisateur
ParaBody
ParaBody 848 Manuel utilisateur
ParaBody
ParaBody 874 Manuel utilisateur
ParaBody
ParaBody 894 Manuel utilisateur
ParaBody
ParaBody 877101 Instructions de montage
ParaBody
ParaBody 855 Manuel utilisateur
ParaBody
ParaBody 832101 Manuel utilisateur
ParaBody
ParaBody 890 Manuel utilisateur
ParaBody
ParaBody 827 Instructions de montage
ParaBody
ParaBody 855103 Manuel utilisateur
ParaBody
ParaBody 888101 Manuel utilisateur
