Pani BP2,5CT Manuel utilisateur
Stage Projector BP 2,5 CT Pani Projection and Lighting Vertriebs GmbH
Version December 2009
CONTENTS
Page
1) Dimension Drawing......................................................3
1.1) Projector.................................................................3
1.1.1) Yo e Assembly "Standing"....................................3
1.1.2) Yo e Assembly "Hanging".....................................3
1.2) Ballast....................................................................3
1.2.1) Type CBI................................................................3
1.2.2) Type BC.................................................................3
2) Position Drawing.......................................................4-7
2.1) Projector
Legend for 2.1)......................................................4
2.2) Control Panel on the Projector
Legend for 2.2)......................................................4
2.3) Ballast
2.3.1) Type CBI.............................................................5-6
2.3.2) Type BC.................................................................7
3) Mounting Accessories............................................8-10
3.1) Undercarriage for
Projectors of the "Compact"-Series.......................8
3.2) Rolling Undercarriage for
Projectors of the "Compact"-Series.......................8
3.3) Projector Cart for
Projectors of the "Compact"-Series.......................9
3.4) Hanging Apparatus for
Projectors of the "Compact"-Series.......................9
3.5) 28mm DIN- Stud with
Welded Mounting Plate.......................................10
) Construction..........................................................10-11
4.1) Mechanical Construction of the Projector...........10
4.2) Electrical Assembly of the Projector....................10
4.3) Slide Carrier and Slide Cooling Fan....................10
4.3.1) Electrical Connection of the
Slide Cooling Ventilator Fan................................11
4.3.2) Operating Mode "Standard - Low Noise"............11
5) Operating Tips.......................................................11-12
5.1) HMI- Lamp.............................................................9
5.1.1) Installation and Replacement
of the HMI- Lamp...................................................9
5.1.2) Lamp Adjustment............................................9+10
5.2) Vertical Adjustment of the Projector....................10
5.3) Yo e Assembly for
Standing or Hanging Configuration.....................10
5.4) Using the Tilt Angle Meter...................................10
2
Stage Projector BP 2,5 CT Pani Projection and Lighting Vertriebs GmbH
Page
6) Position Drawing Condenser System......................13
7) Electrical Connection...........................................13-14
7.1) Main Connection..................................................13
7.2) Connecting Cable Ballast – Projector.................13
7.3) Remote Ignition - DMX 512................................14
8) Objective Lenses........................................................14
8.1) Front Condenser Lens.........................................14
8.2) Projection Objective.............................................14
8.3) Effect-and Varioobjective....................................14
IMPORTANT REMARKS...................................1
9) Projection Diagram....................................................15
10) Slide (Transparency) Material...................................16
11) Electrical Schematic (models of ballast: CBI and BC)..17-18
12) Basic Unit as Delivered.............................................19
13) Accessories...........................................................19-20
1 ) General Technical Data.............................................21
15) Spare Parts............................................................21-23
PANI Projection and Lighting Vertriebs GmbH
A – 1070 Wien, Kandlgasse 23
Austria, Europe
Tel.: + 43 1 / 521 08 – 0
Fax.: + 43 1 / 526 42 87
E – mail: light@pani.com
Internet: www.pani.com
3
Stage Projector BP 2,5 CT Pani Projection and Lighting Vertriebs GmbH
1) Dimension Drawing
1.1) Projector
1.1.1) Mounting Yoke"Standing"
1.1.2) Mounting Yoke"Hanging"
1.2) Ballast
1.2.1) Type CBI 1.2.2) Type BC
4
6957
PANI A USTRIA
O.C. 12 01
Type G50 3
4
2
13
15
8
1
11 10
12 3 14
Stage Projector BP 2,5 CT Pani Projection and Lighting Vertriebs GmbH
2) Position Drawing
2.1) Projector
Legend
(1) Adjustable Clamp Lever for Quic Adjust (On Both Sides)
(2) Hand Wheel for Fine Adjustment
(3) Lamp Adjustment
(4) Fastener for Housing Cover
(5) Housing Cover
(6) Objective Support Bolts
(7) Telescoping Rails
(8) Support Yo e
(9) Adjustable Clamp Lever for Front Plate
(10) Slide Carrier
(11) Slide Carrier Loc ing Pin
(12) Mode Switch "Standard - Low Noise"
(13) Ventilator Connector
(14) Ventilator for Slide Cooling
(15) Mounting Plate for Control Box G405/..
2.2) Control Panel on the Projector
Legend
(1) Power Indicator
(2) ON- Push-button
(3) OFF- Push-button
(4) Elapsed Hour Counter
(5) Ballast Connection
(6) Outlets for auxilliary circuits
(230 VAC) Amphenol 4-pole
(7) Remote Ignition DMX 512
2.3) Ballast
2.3.1) Type CBI (new standard type)
5
Stage Projector BP 2,5 CT Pani Projection and Lighting Vertriebs GmbH
Control Panel on the Ballast:
(1) ON- Push-button (green)
Illuminated when power is connected to the ballast. When the "ON" - Push-button is
momentarily pressed, the ignition cycle is activated and high voltage is applied to start
the HMI lamp
(2) OFF- Push-button (red)
Lamp voltage is interrupted. It is recommended that the unit be allowed to cool down a
few moments before re-ignition.
ATTENTION: Re ignition within 10 seconds of shut down is not possible because of
circuit reasons!
(3) Remote Switch (remote ignition)
In switch position ON ignition is operated automatically , when power is applied (with
operated main circuit bra er 4).
(4) Main Circuit Breaker
2-pole Magnetic Circuit Brea er
(5) Ground Test Indicator
When depressed the indicator and correct polarity and grounding the orange indicating
lamp glows orange.
(8) Connector for connecting ballast cable
6
10 3 2 1 5
9
12
8
13
1
15
16
11
Stage Projector BP 2,5 CT Pani Projection and Lighting Vertriebs GmbH
(9) Voltage and Frequency Selector
With this turn-switch, operating voltage and frequency may be chosen:
240V/ 50 Hz 220V/ 50Hz and 220V/ 60Hz. (Ballast versions –A and –J have only
frequency selector by a slide switch)
(10) Main Connection Cable
3x 2,5 mm², 2m long with Schu o- Connector
(11) Shock Absorber
4 rubber feet for vibration isolation
Optional Operating Elements (DMX-Control) :
(12) DMX ON/OFF Switch
Activates the DMX – operation mode.
(13) turn-switches for DMX – adress code
Defines the adress for DMX – operation: from top to bottom:
unit position
decade position
hundreds position
(14) LED – indicators:
top indicator green: Operation OK
bottom indicator red: Fault
(15) DMX - OUT
DMX – output
(16) DMX - IN
DMX – Input
Nonstandard accessory for CBI-ballasts on demand:
Trolley
(available in 2 versions, for
transport of 2 or 4 ballasts
together)
Hanging on the hoo s and
stac ing the ballasts enables a
fast, easy and stable ind of
transport albeit over longer
distances.
7
Stage Projector BP 2,5 CT Pani Projection and Lighting Vertriebs GmbH
2.3.1) Type BC
(phased out model)
Control Panel on
the Ballast
(1) Power indicator
lamp
Illuminated when power is connected to the ballast
(2) ON- Push-button (green)
When the "ON" - Push-button is momentarily pressed, the
ignition cycle is activated and high voltage is applied to start the HMI lamp
(3) OFF- Push-button (red)
Lamp voltage is interrupted. It is recommended that
the unit be allowed to cool down a few moments before re-ignition
ATTENTION: Re-ignition within 10 seconds of shut down is not possible.
(4) Remote Switch (remote ignition)
When the switch is rotated 90° cloc wise
(remote mode)ignition is automatic, when power is applied
(5) Main Circuit Breaker
2-pole Magnetic Circuit Brea er
(6) Ground Test Indicator
When depressed the indicator glows yellow indicating correct polarity and
grounding.
(7) Low- Noise Switch
In Low-Noise mode, silent ignition of the lamp is possible
(8) Connector for connecting ballast cable
(9) Voltage and Frequency Selector
With the Main Selector switch, operating voltage and frequency may be chosen
- 240V/ 50 Hz 220V/ 50Hz and 220V/ 60Hz. (only ballast BC2500-EP,
frequency selector only for the other ballast versions)
(10) Ground Indicator Lamp
see No. 6.)
(11) Main Connection Cable
3x 2,5 mm2, 2m long with Schu o- Connector.
8
1 2 611 10
4
3
587
9
Stage Projector BP 2,5 CT Pani Projection and Lighting Vertriebs GmbH
3) Mounting Accessories
For standing and hanging projector installations, the following options are available.
3.1) Undercarriage for Projectors of the "Compact"-Series
Horizontal fine adjustment
(+/-6°) and telescoping rails
provide additional flexibility and
forward stabilization of the
projector with the application of
this accessory
Order Code: 12036
3.2) Rolling Undercarriage for Projectors of the
"Compact"-Series
Horizontal fine adjustment
(+/-6°) and telescoping rails
provide additional flexibility and
forward stabilization of the
projector with the application of
this accessory
Order Code: 12001
9
Stage Projector BP 2,5 CT Pani Projection and Lighting Vertriebs GmbH
3.3) Projector Cart for Projectors of the "Compact"-Series
Rolling cart, with
horizontal (±6°) and
associated vertical
(+18° -20°) adjustment
for projectors and
accessories
(i.e. ZOOM - Objective).
Order Code: 12037
3. ) Hanging Apparatus for Projectors of the "Compact"-
Series
With horizontal positioning (±31°)
and associated fine adjustment
(±6°), for mounting on 2 pipes
ø48mm.
Order Code: 12038
10
Table des matières
Autres manuels Pani Projecteur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
