Pani BP 4 CT Manuel utilisateur
Stage Projector BP 4 CT Pani Projection and Lighting Vertriebs GmbH
2
Status of February 2010 CONTENTS
Page
1) Dimension Drawing
1.1) Projector........................................................................3
1.1.1) Yoke Assembly "Standing"............................................3
1.1.2) Yoke Assembly "Hanging" ............................................3
1.2) Ballast...........................................................................4
2) Position Drawing
2.1) Projector
Legend for 2.1) .............................................................5
2.2) Control Panel on the Projector
Legend for 2.2) .............................................................6
2.3) Ballast...........................................................................7
Control Panel on the Ballast.........................................7
3) Mounting Accessories
3.1) Undercarriage for
Projectors of the "Compact"-Series...............................9
3.2) Rolling Undercarriage for
Projectors of the "Compact"-Series...............................9
3.3) Projector Cart for
Projectors of the "Compact"-Series.............................10
3.4) Hanging Apparatus for
Projectors of the "Compact"-Series.............................10
3.5) 28mm DIN- Stud with
Welded Mounting Plate ..............................................10
4) Construction
4.1) Mechanical Construction of the Projector...................11
4.2) Electrical Assembly of the Projector ...........................11
4.3) Slide Carrier and Slide Cooling Fan...........................11
4.3.1) Electrical Connection of the
Slide Cooling Ventilator Fan.......................................11
4.3.2) Operating Mode "TORBO -Standard -Low Noise"....11
5) Operation
5.1) HMI-Lamp ..................................................................12
5.1.1) Installation and Replacement
of the HMI-Lamp ........................................................12
5.1.2) Lamp Adjustment ....................................................12
5.2) Vertical Adjustment of the Projector............................12
5.3) Yoke Assembly for
“Standing” or “Hanging Configurations”......................12
5.4) Using the Tilt Angle Meter ..........................................13
6) Condenser System
Position Drawing and Legend.....................................13
Stage Projector BP 4 CT Pani Projection and Lighting Vertriebs GmbH
3
Page
7) Electrical Connection........................................................14
7.1) Main Power Connection
7.2) Connecting Cable Ballast -Projector
7.3) Remote Ignition -DMX 512
8) Objective Lenses...............................................................15
8.1) Front Condenser Lens
8.2) Projection Objective Lenses
8.3) Effect-and Varioobjective Lenses
IMPORTANT NOTES .................................................15
9) Projection Diagram............................................................16
10) Slide (Transparency) Material ..........................................17
11) Electrical Schematic..........................................................18
12) Basic Unit as Delivered.....................................................19
13) Accessories .................................................................19+20
14) General Technical Data.....................................................21
15) Spare Parts....................................................................22-25
PANI Projection and Lighting Vertriebs GmbH
A –1070 Vienna, Kandlgasse 23
Austria, Europe
Tel.: + 43 1 / 521 08 – 0
Fax.: + 43 1 / 526 42 87
E –mail: [email protected]
Internet: www.pani.com
Stage Projector BP 4 CT Pani Projection and Lighting Vertriebs GmbH
4
1) Dimension Drawing
1.1) Projector
1.1.1) Yoke Assembly "Standing"
1.1.2) Yoke Assembly "Hanging"
Stage Projector BP 4 CT Pani Projection and Lighting Vertriebs GmbH
5
1.2) Ballast
BP4
Compact
Stage Projector BP 4 CT Pani Projection and Lighting Vertriebs GmbH
6
2) Position Drawing
2.1) Projector
Legend
1) Adjustable Clamp Lever for Quick Adjust (On Both Sides)
(2) Hand Wheel for Fine Adjustment
(3) Lamp Adjustment
(4) Fastener for Housing Cover
(5) Housing Cover
(6) Objective Support Bolts
(7) Telescoping Rails
(8) Support Yoke
(9) Adjustable Clamp Lever for Front Plate
(10) Slide Carrier
(11) Slide Carrier Locking Pin
(12) Mode Switch "TURBO -Standard -Low Noise"
(13) Ventilator Connector
(14) Ventilator for Slide Cooling
(15) Mounting Plate for Control Box G405/..
Stage Projector BP 4 CT Pani Projection and Lighting Vertriebs GmbH
7
2.2) Control Panel on the Projector
Legend
(1) Power Indicator
(2) ON-Push-button
(3) OFF-Push-button
(4) Elapsed Hour Counter
(5) Remote Connection
(6) Power Connection
(7) Outlets for auxilliary circuits (230 VAC) Amphenol 4-pole
(8) Remote Ignition DMX 512
Stage Projector BP 4 CT Pani Projection and Lighting Vertriebs GmbH
8
2.3) Ballast
Control Panel on the Ballast
(1) Power indicator lamp
Illuminated when power is connected to the ballast
(2) ON-Push-button (green)
When the "ON" -Push-button is momentarily pressed, the
ignition cycle is activated and high voltage is applied to start the HMI lamp
(3) OFF-Push-button (red)
Lamp voltage is interrupted. It is recommended that
the unit be allowed to cool down a few moments before re-ignition
ATTENTION: Re-ignition within 10 seconds of shut down is not possible.
(4) Remote Switch (remote ignition)
When the switch is rotated 90° clockwise
(remote mode)ignition is automatic, when power is applied
(5) Main Circuit Breaker
2-pole Magnetic Circuit Breaker
BP 4
Compact
Stage Projector BP 4 CT Pani Projection and Lighting Vertriebs GmbH
9
(6) Ground Test Indicator
When depressed the indicator glows yellow indicating correct polarity and
grounding.
(7) Remote Cable to the Projector
(8) Remote Fuse F 2, 2 AT (melting fuse)
(9) Ground Control Lamp
(10) Lamp Current Cable to the Projector
(11) Remote Fuse F 4, 10 AT (melting fuse)
(12) Low-Noise Switch
In Low-Noise mode, silent ignition of the lamp is possible
(13) Main Connection Cable
3x 4 mm2, 2 m long with free ends.
(14) Voltage and Frequency Selector on Ballast BC 4000/E
(other types of ballast adequate)
ATTENTION: disconnect the ballast from the power supply
The lid on top of the ballast [Pos. 2.3(14)] can be removed after unscrewing
the cross screws so that the voltage and the frequency may both be set by
changing the connections 22 and 19
(15) Slide for fixing the vertical position of transporting grip
(16) Snap lock for fixing horizontal position of transporting grip
Stage Projector BP 4 CT Pani Projection and Lighting Vertriebs GmbH
10
3) Mounting Accessories
For standing and hanging projector installations, the following options are available.
3.1) Undercarriage for Projectors of the "Compact"-Series
Horizontal fine
adjustment (+/-6°) and
telescoping rails provide
additional flexibility and
forward stabilization of
the projector with the
application of this
accessory
Order Code: 12036
3.2) Rolling Undercarriage for Projectors of the
"Compact"-
Series
Horizontal fine
adjustment (+/-6°) and
telescoping rails provide
additional flexibility and
forward stabilization of
the projector with the
application of this
accessory
Order Code: 12001
Table des matières
Autres manuels Pani Projecteur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
