Panasonic PTL6500U - LCD PROJECTOR Manuel utilisateur

VED0103310C5

D10

LCD Projector

PT-L6500U / PT-L6500E/ PT-L6600U / PT-L6600E/ PT-

L6500UL / PT-L6500EL / PT-L6600UL / PT-L6600EL

SPECIFICATIONS

1. SafetyPrecautions

1.1. General Guidelines

-Forcontinuedsafety, no modification ofanycircuitmust be

attempted.

-Unplug thepowercordfromthepoweroutlet beforedisassembling

thisprojector.

-Itisadvisabletouse anisolation transformerintheACpowerline

beforetheservice.

-Observetheoriginal leaddress during theservice. Ifashortcircuit

isfound, replace all theparts overheatedordamagedbytheshort

circuit.

-Aftertheservice, all theprotectivedevices suchas insulation

barriers, insulation papers, shields, and isolation R-C

combinationsmust beproperlyinstalled.

-Aftertheservice, check theleakagecurrenttopreventthe

customerfromgetting anelectricshock.

1.2. LeakageCurrentCheck

1. Preparethemeasuring circuitas showninFig.1.

Besuretouse avoltmeterhaving theperformance describedin

Table1.

Fig. 1

Table1

Fig. 2

2. Assemblethecircuitas showninFig. 2. Plug thepowercordina

poweroutlet.

3. Connect M1toT1according toFig. 2and measurethevoltage.

4. Changetheconnection ofM1fromT1toT2and measurethe

voltageagain.

5. Thevoltmetermust read0.375 Vorlowerinbothofsteps3and 4.

Thismeansthat thecurrentmust be0.75 mAorless.

6. Ifthereading isoutoftheabovestandard, theprojectormust be

repairedand recheckedbeforereturning tothecustomerbecause

ofapossibilityofanelectricshock.

1.3. UVPrecaution and UHMLampPrecautions

-Besuretounplug thepowercordfromthepoweroutlet when

replacing thelamp.

-Because thelampreaches averyhigh temperatureduring its

operation, waituntil itcoolscompletelywhenreplacing theLamp

Unit.

-Thelampemits small amounts ofUV-radiation, avoiddirect-eye

contact withthelight.

-Because thehigh pressurelampinvolves arisk ofexplosion, never

touchthelampwireleadduring theservice. (See Fig. 3)

Fig. 3

2. Operating Instructions

2.1. Operating Instructions

2.2. GuidetoLensInstallation

3. Self-Check Mode

Thismodeisusedtonarrowdownthelocation ofthefailure.

3.1. Proceduretoentertheself-check mode

Whilepressing theVOLUME "-" button on theremotecontrol unit, press theleft-arrow" "

button on themainunit3secondsor longer.

AnotherMethod

(canbeusedfor hard topress thebutton on themainunit, e. g. installedon theceiling)

1. Select "OSD"on theOPTION1menu.

2. MENU OPTION1OSD

3. Press the"ENTER"button on theremote control unit3secondsor

longerand displaystheservice supportmodemenu.

4. Select "SELFCHECK"and press on the"ENTER"button on the

remote control unit.

3.2. SelfCheck Displayand Contents

3.3. Canceling theself-check mode

Press theMENU button on themainunitor theremotecontrol unit.

4. Service Mode

Thismodeisusedtodisplay eightkindsoftestpatterns(see below)inthefour colors(White,

Red, Greenand Blue).

PT-L6500**

Cross, Horizontal 1line, Vertical lines on alternatedots, 1-dotpattern, Horizontal 16 lines, Vertical

16 lines, 16 lines crosshatch, Nopattern

PT-L6600**

Horizontal 1line, Vertical lines on every2dots, Nopattern, Checker, Crosshatch, Cross, 5:4&4:3

display frames

Note:

Ontheservice mode, displaysabovepatternsbyeachcolorwithout

test equipmentsuchas PCorSG. Use theservice modefor

convergence adjustmentand soon.

4.1. Proceduretoentertheservice mode

-Select "FRONT/REAR"on theOPTION1menu.

MENU OPTION1FRONT/REAR

-Whilepressing the"VOLUME+"button on theremote control unit,

press theleft-arrow " "button on themainunit3secondsor

longertoentertheservice mode.

AnotherMethod

(canbeusedfor hard topress thebutton on themainunit, e. g. installedon theceiling)

-Select "OSD"on theOPTION1menu.

-MENU OPTION1 OSD

-Press the"ENTER"button on theremote control unit3secondsor

longerand displaystheservice supportmodemenu.

-Select "SERVICEMODE"and press on the"ENTER"button on the

remote control unit.

Note:

Intheservice mode, pressing theup-arrow " "ordown-arrow " "

button on theremote control unitallowsthetest patternselection

and theleft-arrow " "orright-arrow " "button thecolorselection

(White / Red/ Green/ Blue).

4.2. Canceling theservice mode

Press theMENU button on themainunitor theremotecontrol unit.

5. Service Support Mode

Thisprojector has Service SupportModeMenu inaddition tostandard on-screenmenus.

5.1. Proceduretoentertheservice supportmode

-Select "OSD"on theOPTION1menu.

MENU OPTION1OSD

-Press the"ENTER"button on theremote control unit3secondsor

longerand displaystheservice supportmodemenu.

5.2. Service SupportModeMenu and Functions

-FREEZEMSG

Switching on/off "FREEZE", "MUTE"and "PICTUREMUTE"on-

screendisplays

-SELFCHECK

To entertheself-check mode

-SERVICEMODE

To entertheself-check mode

-REMOCONFRONT

Specifies theremote control receiver(front) availableornot

available.

-REMOCONREAR

Specifies theremote control receiver(rear)availableornot

available.

-CONT. PANEL

Specifies therearcontrol panel availableornotavailable.

5.3. Canceling theservice supportmode

Press theMENU button on themainunitor theremotecontrol unit.

6. Using the SERIALConnector

SERIALconnector whichison thesideinterface panel oftheprojector conformstoRS-232C

standard. Thisprojector canbecontrolledbyaPCwhichisconnectedas shownin"6.1.

Connection".

For controlling thisprojector byaPC, requires communication softwareon themarket, and

inputscontrol commandsaccording tocommunication settingsand basicformatbelow.

6.1. Connection

Note:

Use apropercommunication cablewhichissuitableforthePCto

connect SERIALconnectorand thePC.

6.2. PinLayoutand Signal Names forSERIALConnector

6.2.1. SERIALINTerminal

6.2.2. SERIALOUTTerminal

6.3. Communication Settings

Signal Level Contents Description

Sync. method Asynchronous Synchronizes every1

character

bits)

Baud rate Conforms

to 9600 bps Datatransferspeed

Parity RS-232C None Error detection method

Characterlength standard 8bits Numberofbitcomposing 1

character

Stop bit 1bit Uses stop bitwhen

asynchronous

method

X parameter Notused

S parameter Notused

6.4. BasicFormat

Thedatasentfrom thePCtotheprojector istransmittedintheformatshownbelow.

Cautions:

-Whenitisunnecessarytodesignate anIDcode, send theformat

withouttheparttoIDdesignate it. Inthiscase, theprojectorsends

acall back tothePCirrespectiveoftheprojectorIDsetting.

-Add aparameterwhenthecommand function isrequiredofit.

-Ifsending multiplecommands, check that acall back has been

receivedfromtheprojectorforonecommand beforesending the

next command.

Notes:

-Whenacommand whichdoes notrequireparametersissent, the

colon (:)isnotrequired.

-Ifacommand issentwithaprojectorIDspecified, theprojectorwill

returncall back onlyiftheIDcontainedinthecommand matches

theprojectorIDortheprojectorIDisset toALL.

-ProjectorIDsupportedon theRS-232Cinterface is00 (ALL)to99.

-Whenusing control fromREMOTEterminal, commandscannotbe

receivedat SERIALterminal.

6.5. Control / QueryCommands

Control Commands

Autres manuels pour PTL6500U - LCD PROJECTOR

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panasonic Projecteur

Panasonic

Panasonic PT-LX26H Manuel du système

Panasonic

Panasonic PT-D5000U Manuel utilisateur

Panasonic

Panasonic PT-AR100 Manuel utilisateur

Panasonic

Panasonic PT-D5600U Manuel utilisateur

Panasonic

Panasonic PT-AX100U Manuel utilisateur

Panasonic

Panasonic PT-F200NTE/PT-FW100NTE Manuel utilisateur

Panasonic

Panasonic PT-TW230U Manuel utilisateur

Panasonic

Panasonic PT-DZ870E Manuel utilisateur

Panasonic

Panasonic PTLB75U - LCD PROJECTOR Manuel utilisateur

Panasonic

Panasonic PT-RZ670 series Instructions d'installation

Panasonic

Panasonic PT-VZ580 Mode d'emploi

Panasonic

Panasonic PT51G43 - 51" PROJECTION TV Manuel utilisateur

Panasonic

Panasonic PT-CW230E Manuel utilisateur

Panasonic

Panasonic PTLM1U - LCD PROJECTOR Manuel utilisateur

Panasonic

Panasonic PT-CX200 Manuel du système

Panasonic

Panasonic PT-51SX30 Manuel utilisateur

Panasonic

Panasonic PT-D7500E Manuel utilisateur

Panasonic

Panasonic PT-CW331R Manuel utilisateur

Panasonic

Panasonic PT_AT6000E Manuel utilisateur

Panasonic

Panasonic PT-AE3000E Manuel utilisateur

Panasonic

Panasonic PT-AE1000U - LCD Projector - HD 1080p Manuel utilisateur

Panasonic

Panasonic PT-LB51NTEA Manuel utilisateur

Panasonic

Panasonic PT-FW100NTEA Manuel utilisateur

Panasonic

Panasonic PT-TW330E Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur