Panasonic PAN1311/21 USB Manuel utilisateur

No.

DS-PAN1311/21USB

REV.

1.1

PAGE

1 of 11

Quick Start Guide

Evaluation Board (EVB) PAN1311/21 USB

DATE

15.09.2011

PANASONIC ELECTRONIC DEVICES EUROPE

GmbH

DESIGNED

Erstellt

Quick Start Guide

Evaluation Board (EVB) PAN1311/21 USB

No.

DS-PAN1311/21USB

REV.

1.1

PAGE

2 of 11

Quick Start Guide

Evaluation Board (EVB) PAN1311/21 USB

DATE

15.09.2011

PANASONIC ELECTRONIC DEVICES EUROPE

GmbH

DESIGNED

Erstellt

1. CONTENT

1. Content...................................................................................................................................2

2. Introduction ............................................................................................................................3

2.1 Related documents...............................................................................................................3

4. Functional overview................................................................................................................3

5. Connection setup ...................................................................................................................4

5.1 Software start and navigation ...............................................................................................4

5.2 Port configuration .................................................................................................................5

5.3 Firmware handling................................................................................................................6

5.4 Command tab navigation......................................................................................................7

5.5 Creating a connection...........................................................................................................8

6. Schematic ..............................................................................................................................9

7. Document Information ..........................................................................................................10

8. General Information..............................................................................................................11

8.1 Waiver................................................................................................................................11

9. Life Support Policy ...............................................................................................................11

No.

DS-PAN1311/21USB

REV.

1.1

PAGE

3 of 11

Quick Start Guide

Evaluation Board (EVB) PAN1311/21 USB

DATE

15.09.2011

PANASONIC ELECTRONIC DEVICES EUROPE

GmbH

DESIGNED

Erstellt

2. INTRODUCTION

This document should provide the minimum knowledge needed to establish a simple

connection between two PAN1321ETU USB Evaluation Boards (EVB) using Infineon

eBMU_SPP_Toolbox software. For this limited information is granted. To learn about all

aspects of the software please refer to the related documents listed below.

2.1 RELATED DOCUMENTS

For further information on Infineon eBMU_SPP_Toolbox software and it’s implemented AT

command set please refer to:

•PAN13x1_ReleaseNote_SPP_AT_SW08_V1.8_RN_Rev1.0_DRAFT

•PAN13x1_ReleaseNote_SPP_AT_SW21_V2.1_RN_Rev1.0_DRAFT -iPhone version

•PAN13x1_SPP_AT_UserManual_SoftwareDescription_Rev5.0 DRAFT

•PAN1321_AN_DesignGuide_Rev2 1

•User's_Manual_PAN1311_V20.xx_Rev1.1

•User's_Manual_PAN1321_V20.xx_Rev3.1

4. FUNCTIONAL OVERVIEW

The figure below shows an overview of the Evaluation Board. If there is the need to connect

your µController to the EVB please de-solder R1, R2, R3, R4.

For more details please refer also to the schematic in chapter Schematic.

Figure 2 : Evaluation Board Overview

Hardware

Reset

UART to USB

Converter Section

For interfaces

description refer to

schematic

Power Supply

section

No.

DS-PAN1311/21USB

REV.

1.1

PAGE

4 of 11

Quick Start Guide

Evaluation Board (EVB) PAN1311/21 USB

DATE

15.09.2011

PANASONIC ELECTRONIC DEVICES EUROPE

GmbH

DESIGNED

Erstellt

5. CONNECTION SETUP

This chapter describes how to use the eBMU_SPP_Toolbox software in order to send simple

data packages from one EVB to the other.

5.1 SOFTWARE START AND NAVIGATION

Browse to the folder where the eBMU_SPP_Toolbox.exe file is located and start it. The user

interface (figure 2) is shown.

Figure 4 : Toolbox start up screen

No.

DS-PAN1311/21USB

REV.

1.1

PAGE

5 of 11

Quick Start Guide

Evaluation Board (EVB) PAN1311/21 USB

DATE

15.09.2011

PANASONIC ELECTRONIC DEVICES EUROPE

GmbH

DESIGNED

Erstellt

5.2 PORT CONFIGURATION

Please note that the eBMU Toolbox can handle only COM port numbers below 10. You can

configure in the System Hardware settings in your operating system. The USB driver can be

found in the installation folder.

On the settings tab the communication via COM port is handled. It is possible to set a

number of default parameters for both EVBs and to save/load all the changes made to this

page (saving the settings will also make the program remember the selected port numbers).

Please select the right port numbers for both EVBs (found at Windows OS: control panel 

system hardware device manager Ports (COM & LPT)) and click the buttons

open/close 1 & open/close 2. A status message should appear below the text fields (figure

3). Leave the rest unchanged for now.

Figure 5 : COM port setup

No.

DS-PAN1311/21USB

REV.

1.1

PAGE

6 of 11

Quick Start Guide

Evaluation Board (EVB) PAN1311/21 USB

DATE

15.09.2011

PANASONIC ELECTRONIC DEVICES EUROPE

GmbH

DESIGNED

Erstellt

5.3 FIRMWARE HANDLING

At the testing tab firmware can be downloaded (Download image) to the EVB and a number

of changes can be made to it (Change BD-data) like assigning a unique BT address (e.g.

0003199E8B73) and oscillator trim value. Make sure that the Production mode is enabled

before any of these buttons on this tab are used. To do this mark On and confirm with a click

on Production mode. The text field should inform you about of success of this procedure. Be

advised to do a hardware reset (push button on EVB) after all changes were made.

Please note:

The BD_Address and OSC_Trim value have to be read out by “Read BD Address” command

before downloading. They have to be programmed by “Change BD-data” command after

writing the new image.

Figure 6 : Testing tab

No.

DS-PAN1311/21USB

REV.

1.1

PAGE

7 of 11

Quick Start Guide

Evaluation Board (EVB) PAN1311/21 USB

DATE

15.09.2011

PANASONIC ELECTRONIC DEVICES EUROPE

GmbH

DESIGNED

Erstellt

5.4 COMMAND TAB NAVIGATION

At the Commands tab are several commands listed for easy click-and-use. Note the colour

coding identifying commands by their intended usage:

•Yellow: Settings and informational commands.

•Pink: Security related commands.

•Green: Connection related.

•Red: Disconnection commands.

•Blue: Data transfer

•Light blue: Accept connection

•White: Sniff (during connection)

Figure 7 : Command tab and used commands

For simple data transfer find the needed commands marked in figure 5. The Custom

Command button can be used to issue any command of the command set (refer to

PMB8753-2_SPP_AT_specification_R1.pdf).

No.

DS-PAN1311/21USB

REV.

1.1

PAGE

8 of 11

Quick Start Guide

Evaluation Board (EVB) PAN1311/21 USB

DATE

15.09.2011

PANASONIC ELECTRONIC DEVICES EUROPE

GmbH

DESIGNED

Erstellt

5.5 CREATING A CONNECTION

To send data from one EVB to the other one of them must be prepared for connection, while

the other will request a connection. Follow these steps:

1. Click on Make Discoverable on Device A. Choose option 3: Inquiry_Page Scan

enabled. The text field should state the issued command sent (arrow) and the OK

response (arrow). Now device A can be found by other devices by both available

scan methods.

2. Click on Register Local Service. There are some options to change identification of

the new service but the default values are ok. Simply choose Send. This service now

can be found by other devices of the network.

3. Click the Auto Accept Connection Requests command and choose option 1. EVB A

will auto accept connection requests from now on. Device A is now ready for

connection!

4. Get the address of EVB A with the help of Read BD Address. In the text field you will

find the desired information (e.g. “[…] <-- +RRBDRES=0003199E8B73, […]”). With

this Device A can be addressed when…

5. …issuing Connection Request from Device B. Type or copy the BD address of

Device A into the BD Address 0x text field. Name the service channel under which

the service of Device A was registered in step 2. If no changes were in step 2 service

channel 01 should do. Click send. After a short while both Devices should state

connected.

6. Done! Now data strings can be sent from one EVB to the other with the Send Data

command. Data send and received will be displayed in the text fields. Another click

on Send Data will close its dialog box.

Your text fields should look like Figure 6 or alike after step 1 to 5 were made. If problems or

errors are encountered feel free to hardware reset (EVB push button) both boards and start

over with step 1.

Figure 8 : text field output from step 1 to 6

No.

DS-PAN1311/21USB

REV.

1.1

PAGE

9 of 11

Quick Start Guide

Evaluation Board (EVB) PAN1311/21 USB

DATE

15.09.2011

PANASONIC ELECTRONIC DEVICES EUROPE

GmbH

DESIGNED

Erstellt

6. SCHEMATIC

No.

DS-PAN1311/21USB

REV.

1.1

PAGE

10 of 11

Quick Start Guide

Evaluation Board (EVB) PAN1311/21 USB

DATE

15.09.2011

PANASONIC ELECTRONIC DEVICES EUROPE

GmbH

DESIGNED

Erstellt

7. DOCUMENT INFORMATION

Revision

Version

Date

Datum

Modification / Remarks

Änderungen / Bemerkungen

1.0 18.04.2011 Initial version

1.1 15.09.2011 Updated documentation information in chapter 2.1

Table 3 : Document version

Table des matières

Autres manuels Panasonic Carte mère

Panasonic

Panasonic PGA26E07BA-SWEVB008 Manuel utilisateur

Panasonic

Panasonic PAN9320ETU Manuel utilisateur

Panasonic

Panasonic EVB-NN30312A Manuel utilisateur

Panasonic

Panasonic PAN9420 Manuel utilisateur

Panasonic

Panasonic PGA26E07BA-SWEVB006 Manuel utilisateur

Panasonic

Panasonic NN32251A Manuel utilisateur

Panasonic

Panasonic AN33014UA Manuel utilisateur

Panasonic

Panasonic PAN4570 Manuel utilisateur

Panasonic

Panasonic PAN9520 Manuel utilisateur

Panasonic

Panasonic EvalBoard PAN4555 Manuel utilisateur

Panasonic

Panasonic Grid-EYE Manuel utilisateur

Panasonic

Panasonic AN30182A-EVB Manuel utilisateur

Panasonic

Panasonic Grid-EYE Manuel utilisateur

Panasonic

Panasonic NN30320A Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur