Panasonic EY76A1 Manuel utilisateur

© Panasonic Corporation 2019. All rights reserved.

Unauthorized copying and distribution is a violation

of law.

ORDER NO. PTD1909E04CE

Cordless Impact Driver

Model No. EY76A1

Europe

TABLE OF CONTENTS

PAGE PAGE

1 Warning -------------------------------------------------------------- 2

2 Specifications ----------------------------------------------------- 2

3 Troubleshooting Guide ----------------------------------------- 3

4 Disassembly and Assembly Instructions ---------------- 6

5 Exploded View and Replacement Parts List -----------10

2

1Warning

Caution:

• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70 °F (30 - 40 °C) higher.

Please use a soldering iron with temperature control and adjust it to 750 ± 20 °F (400 ± 10 °C). In case of using high temperature

soldering iron, please be careful not to heat too long.

• Pb free solder will tend to splash when heated too high (about 1100°F / 600 °C).

2 Specifications

3

3 Troubleshooting Guide

3.1. Troubleshooting Guide

4

5

3.2. Trial Operation (after checking Troubleshooting Guide).

3.2.1. Assembly

• Confirm if there is no gap between housing A and B by pinching lead wires.

• There is no dust or deformation on battery terminals.

• Confirm all screws are tightened firmly.

• Confirm if there is no dirt when repairing.

3.2.2. Operation

• Check whether the tool operates properly in both the forward and reveres directions.

• Check whether the LED lights ON.

• Check whether the tool speed increases continuously as the trigger is gradually engaged.

• Check whether the tool speed is normal after repair and reassembly.

Hard mode: 0 to 2800 rpm at 14.4V/18V.

Medium mode: 0 to 1450 rpm at 14.4V/18V.

Soft mode: 0 to 950 rpm at 14.4V/18V.

• Check whether the remaining battery power indicator lamp lights up or flashes when the Battery level button is pressed.

6

4 Disassembly and Assembly Instructions

* To reduce the risk of injury, always remove battery pack before removing/installing the tool.

* To assemble the tool, start with 4-4 and proceed to 4-1

4.1. How to remove the Housing.

4.2. How to remove the Driving assembly.

1. After removing the plate hook, remove 9 housing screws.

2. Then open the housing B.

3. Remove the interior parts.

4. Remove the interior components from the housing A.

Note: (when assembling)

Route LED lead wires and motor lead wire between the ribs on housing

A like the figure.

Hold the motor assembly, remove the fixation cover assembly and asso-

ciated parts together from the motor assembly.

7

4.3. How to remove the Fixation cover assembly and Driving shaft assembly.

Note: (when assembling)

1. Remove the protector.

2. Remove the interior components from the fixation cover

assembly.

8

4.4. How to remove the Switch assembly, LED harness assembly and

Battery terminal.

Note: (when assembling)

The connect cover cannot be reused after being repaired.

NOTE:(When attaching the connectors/switch).

Apply grease (Permalub) to the indicated by the shaded area.

1. Remove the connector(6-pin/2-pin) covers.

2. Disconnect the connecters or lead wires in order to (1) to (4).

Note:

Exercise care not to bend the terminal fitting.

9

4.5. Wiring and Assembly Points.

Model No. : EY76A1 Exploded View

5 Exploded View and Replacement Parts List

Autres manuels pour EY76A1

1

Table des matières

Autres manuels Panasonic Moteur à percussion

Panasonic

Panasonic EY7541 - CORDLESS IMPACT WRENCH Manuel utilisateur

Panasonic

Panasonic EYFLA7A Manuel utilisateur

Panasonic

Panasonic EY75A7 Manuel utilisateur

Panasonic

Panasonic EY7201-U1 Manuel utilisateur

Panasonic

Panasonic EY7541 - CORDLESS IMPACT WRENCH Instructions d'utilisation

Panasonic

Panasonic EY7206 - 12V IMPACT DRIVER Manuel utilisateur

Panasonic

Panasonic EY75A7 Manuel utilisateur

Panasonic

Panasonic EY75A7 Manuel utilisateur

Panasonic

Panasonic EY7202 - 12V IMPACT DRIVER Manuel utilisateur

Panasonic

Panasonic EY7552 Manuel utilisateur

Panasonic

Panasonic EY7540LN2L Manuel utilisateur

Panasonic

Panasonic EY7206GQW Manuel utilisateur

Panasonic

Panasonic EY7530 Manuel utilisateur

Panasonic

Panasonic EY7202-U1 Manuel utilisateur

Panasonic

Panasonic EY75A1 Manuel utilisateur

Panasonic

Panasonic EY75A7 Manuel utilisateur

Panasonic

Panasonic EY7430 Manuel utilisateur

Panasonic

Panasonic EY7542 - CORDLESS IMPACT WRENCH Manuel utilisateur

Panasonic

Panasonic EYFLA4A Manuel utilisateur

Panasonic

Panasonic EY7540 - IMPACT DRIVER 14.4V Manuel utilisateur

Panasonic

Panasonic EYFPA1J Manuel utilisateur

Panasonic

Panasonic EY6506-U1 Manuel utilisateur

Panasonic

Panasonic EY-6506 Manuel utilisateur

Panasonic

Panasonic EY76A1 Manuel utilisateur

Manuels Moteur à percussion populaires d'autres marques

stayer

stayer IW500D Manuel utilisateur

Makita

Makita DTD152 Manuel utilisateur

Milwaukee

Milwaukee M12 FID Manuel utilisateur

Grizzly

Grizzly H6140 Manuel utilisateur

Makita

Makita BTW450 Manuel utilisateur

Ozito

Ozito LID-3000 Manuel utilisateur

Astro Pneumatic Tool

Astro Pneumatic Tool 1812 Manuel utilisateur

Greenlee

Greenlee HW3 Manuel utilisateur

Sthor

Sthor 57091 Manuel utilisateur

Makita

Makita DTD145 Manuel utilisateur

Hilti

Hilti SIW 2-A12 Manuel utilisateur

Ryobi

Ryobi R18IW3 Manuel utilisateur

Parkside

Parkside PDSSA 20-Li A1 Manuel utilisateur

Flex

Flex FX1471 Manuel utilisateur

SATA

SATA 51075C Manuel technique

Cembre

Cembre NR-11P Manuel utilisateur

Makita

Makita BTP131RFE Manuel utilisateur

DeWalt

DeWalt XR Li-ion DCF902 Manuel utilisateur