Panasonic EY-6506 Manuel utilisateur

Cordless Impact Driver

Akku-Schlagschrauber

Perceuse à impact sans ﬁl

Cacciavite a impatto senza ﬁli

Snoerloze slagschroevendraaier

Destornillador de impacto inalámbrico

Akku-slagboremaskine

Trådlös slagborrmaskin

Ledningløs trykkskrutrekker

Langaton iskuruuviavain

Model No: EY6506

Before operating this unit, please read these instructions completely and save this manual for future use.

Vor Inbetriebnahme des Gerätes, die Betriebsanleitung bitte grüdlich durchlesen und diese Broschüre zum späteren Nachschlagen sorgfältig aufbewahren.

Lire entièrement les instructions suivantes avant de faire fonctionner l’appareil et conserver ce mode d’emploi à des fins de consultation ultérieure.

Prima di usare questa unità, leggere completamente queste istruzioni e conservare il manuale per usi futuri.

Lees deze gebruiksaanwijzing aandachtig door voor u het apparaat in gebruik neemt en bewaar de gebruiksaanwijzing voor eventuele naslag.

Antes de usar este aparato por primera vez, lea todas las instrucciones de este manual y guarde el manual para poderlo consultar en el futuro.

Gennemlæs denne betjeningsvejledning før brugen og gem den til fremtidig brug.

Läs igenom hela bruksanvisningen innan strålkastaren tas i bruk. Spara bruksanvisningen för senere användning.

Før enheten tas i bruk, vennligst les disse alle anvisningene og oppbevar deretter bruksanvisningen for senere bruk.

Lue ohjeet huolella ennen laitteen käyttöönottoa ja säilytä tämä käyttöohje tallessa tulevaa tarvetta varten.

Operating Instructions

Bedienungsanleitung

Instructions d'utilisation

Istruzioni per l’uso

Gebruiksaanwijzing

Manual de instrucciones

Brugsvejledning

Driftsföreskrifter

Bruksanvisning

Käyttöohjeet

Index/Hinweise/Index/Indice/Index/Indice/Indeks/Index/Indeks/Hakemisto

English: Page 4

Deutsch: Seite 12

Français: Page 18

Italiano: Pagina 24

Nederlands: Badzijde 30

Español: Página 36

Dansk: Side 42

Svenska: Sid 48

Norsk: Side 54

Suomi: Sivu 60

FUNCTIONAL DESCRIPTION

FUNKTIONSBESCHREIBUNG

DESCRIPTION DES FONCTIONS

DESCRIZIONE DELLE FUNZIONI

FUNCTIEBESCHRIJVING

DESCRIPCIÓN FUNCIONAL

BESKRIVELSE AF FUNKTIONERNE

FUNKTIONSBESKRIVNING

FUNKSJONSBESKRIVELSE

TOIMINTAKUVAUS

(A)

(C)

(D)

(E)

(B)

(F)

(G)

(A)

6.35 mm (1/4") hex quick connect chuck

6,35-mm-Sechskant-Schnellspannfutter

Mandrin à connexion rapide hexagonal de 6,35 mm (1/4")

Mandrino esagonale da 6,35 mm di rapido collegamento

6,35 mm zeskant-snelspanboorkop

Portabroca de conexión hexagonal rápida de 6,35 mm (1/4 pulg.)

6,35 mm sekskant-hurtigspændeskrue

6,35 mm sexkantig snabbansluten chuck

6,35mm-sekskantet-chuck for hurtigtilkopling

6.35 mm kuusiokulmainen pikakiinnitysistukka

(E)

Battery pack (EY9200)

Akkupack (EY9200)

Batterie (EY9200)

Pacco batteria (EY9200)

Accu (EY9200)

Bloque de pilas (EY9200)

Batteri (EY9200)

Batteri-pakke (EY9200)

Akku (EY9200)

(B)

Forward/Reverse lever

Vorwärts/Rückwärts-Hebel

Levier d’inversion marche avant-marche arrière

Leva di avanzamento/inversione

Voorwaarts/achterwaarts-hendel

Palanca de avance/inversión

Greb til forlæns/baglæns retning

Riktningsomkopplare

Forover/Revers bryter

Eteenpäin/taaksepäin vipu

(F)

Battery pack release button

Akkupack-Entriegelungsknopf

Bouton de libération de batterie

Tasto di rilascio blocco batteria

Accu-ontgrendeltoets

Botón de liberación de la batería recargable

Udløserknap til batteripakning

Batteriets låsknappar

Batteriets utløseerknapper

Akkupaketin irrotuspainikeet

(C)

Variable speed control trigger

Betriebsschalter

Gâchette de commande de vitesse

Grilletto di controllo velocità variabile

Startschakelaar variabele snelheid

Disparador del control de velocidad variable

Kontroludløser for variabel hastighed

Steglös varvtalsreglerare

Hovedbryter, trinnløs

Nopeudensäätökytkin

(G)

Battery charger (EY0110)

Ladegerät (EY0110)

Chargeur de batterie (EY0110)

Carica-batterie (EY0110)

Batterijlader (EY0110)

Cargador de la batería (EY0110)

Batterioplader (EY0110)

Batteriladdare (EY0110)

Batterilader (EY0110)

Akkulaturi (EY0110)

(D)

Bit holder

Elnsatzhalter

Porte-mèche

Portapunta

Bithouder

Portabrocas

Bitholder

Borrspetshållare

Bitsholder

Terän pidin

Read “the Safety Instructions” booklet

and the following before using.

. ADDITIONAL

ADDITIONAL

SAFETY RULES

1) Be aware that this tool is always in

an operating condition, since it does

not have to be plugged into an elec-

trical outlet.

2) When drilling or driving into walls,

floors, etc., “live” electrical wires may

be encountered. DO NOT TOUCH

THE CHUCK OR ANY FRONT

METAL PARTS OF THE TOOL! Hold

the tool only by the plastic handle to

prevent electric shock in case you

drill or drive into a “live” wire.

3) If the bit becomes jammed, immedi-

ately turn the main switch off to pre-

vent an overload, which can damage

the battery pack or motor.

Use reverse motion to loosen

jammed bits.

4) Do NOT operate the Forward/

Reverse lever when the main switch

is on. The battery will discharge

rapidly and damage to the unit may

occur.

5) During charging, the charger may

become slightly warm. This is nor-

mal. Do NOT charge the battery for a

long period.

6) Use only a dry, soft cloth to wipe

the unit. Do NOT use a damp cloth,

thinner, benzine, or other volatile sol-

vents for cleaning.

7) When storing or carrying the tool,

set the Forward/Reverse lever to the

center position (switch lock).

8) Do not strain the tool by holding the

speed control trigger halfway (speed

control mode) so that the motor

stops.

9) Wear ear protectors when using the

tool for extended periods.

10) Young children should be supervised

to ensure that they do not play with

the appliance.

.ASSEMBLY

ASSEMBLY

Attaching or removing bit

NOTE:

When attaching or removing a bit,

disconnect battery pack from tool or

place the switch in the center posi-

tion (switch lock).

1. Hold the collar of quick connect

chuck and pull it against the driver.

2. Insert the bit into the chuck.

3. The bit holder will return to its origi-

nal position when it is released.

4. Pull the bit to make sure it does not

come out.

5. To remove the bit, pull back on the

bit holder in the same way.

CAUTION:

If the bit holder does not return to its

original position or the bit comes out

when pulled on, the bit has not been

properly attached. Make sure the bit

is properly attached before use.

Attaching or removing

battery pack

1. To connect the battery pack:

Insert the battery pack. It snaps into

place to indicate proper connection.

2. To remove the battery pack:

Press the two buttons on the sides

of the battery pack. Slide the battery

pack out of the tool body.

.OPERATION

OPERATION

Switch and Forward

Reverse

lever Operation

(Forward ( ), Switch lock, Reverse ( ))

CAUTION:

Do not operate Forward/Reverse lever

until the bit comes to a complete stop.

Forward Rotation Switch

Operation

1. Push the lever for forward rotation.

2. Depress the trigger switch slightly to

start the tool slowly.

3. The speed increases with the amount

of depression of the trigger for efficient

tightening of screws. The brake oper-

ates and the bit stops immediately

when the trigger is released.

4. After use, set the lever to its center

position (switch lock).

Reverse Rotation Switch

Operation

1. Push the lever for reverse rotation.

Check the direction of rotation before

use.

2. Depress the trigger switch slightly to

start the tool slowly.

3. After use, set the lever to its center

position (switch lock).

CAUTION

To eliminate excessive temperature

increase of the tool surface, do not

operate the tool continuously using

two or more battery packs. Tool

needs cool off time before switching

to another pack.

For Appropriate use of

Battery pack

Ni-MH Battery pack (EY9200)

Charge the Ni-MH battery fully be-

fore storage in order to ensure a

longer service life.

The ambient temperature range

is between 0°C (32°F) and 40°C

(104°F).

If the battery pack is used when

the battery temperature is below

0°C (32°F), the tool may fail to func-

tion properly. In that case, charge the

battery until charging is completed for

appropriate functioning of the battery.

When battery pack is not in use,

keep it away from other metal objects

like: paper clips, coins, keys, nails,

screws, or other small metal objects

that can make a connection from one

terminal to another.

Shorting the battery terminals togeth-

er may cause sparks, burns or a fire.

When operating with a Ni-MH bat-

tery pack, make sure the place is

well-ventilated.

Battery Pack Life

The rechargeable batteries have a lim-

ited life. If the operation time becomes

extremely short after recharging,

replace the battery pack with a new one.

Charging

NOTE:

When you charge the battery pack for

the first time, or after prolonged stor-

age, charge it for about 24 hours to

bring the battery up to full capacity.

Battery charger (EY0110)

1. Plug the charger into the AC outlet.

NOTE:

Sparks may be produced when the

plug is inserted into the AC power

supply, but this is not a problem in

terms of safety.

2. Insert the battery pack firmly into

the charger.

Battry pack

To AC

outlet

Battery

charger

3. During charging, the charging lamp

will be lit.

When charging is completed, an

internal electronic switch will auto-

matically be triggered to prevent

overcharging.

Charging will not start if the bat-

tery pack is warm (for example,

immediately after heavy-duty

operation).

The orange standby lamp will be lit

until the battery cools down. Charging

will then begin automatically.

4. When charging is completed, the

charging lamp will start flashing

quickly in green color.

5. When in any of the conditions that

battery pack is too cool, or the bat-

tery pack has not been used for a

long time, the charging lamp is lit. In

this case, charging takes longer to

fully charge the battery pack, than

the standard charging time.

If a fully charged battery pack is

inserted into the charger again,

the charging lamp light up. After

several minutes, the charging

lamp may flash quickly to indicate

the charging is completed.

6. If the charging lamp does not light

immediately after the charger is

plugged in, or if after the standard

charging time the lamp does not go

off, consult an authorized dealer.

NOTE:

When charging a cool battery pack

(below 5°C (41°F)) in a warm place,

leave the battery pack at the place

and wait for more than one hour to

warm up the battery to the level of

the ambient temperature. Other-

wise battery pack may not be fully

charged.

Cool down the charger when charg-

ing more than two battery packs

consecutively.

Do not insert your fingers into con-

tact hole, when holding charger or

any other occasions.

CAUTION:

Do not use power source from an

engine generator.

Do not cover vent holes on the

charger and the battery pack.

.LAMP INDICATIONS

Red Flashing

Red Lit

Green Flashing quickly

Orange Lit

Orange Flashing

Charger is plugged into the AC outlet.

Ready to charge.

Now charging

Charging is completed.

Battery pack is warm. Charging will begin

when temperature of battery pack drops.

Charging is not possible. Clogged with

dust or malfunction of the battery pack.

.TIGHTENING TORQUE

The power required for tightening a bolt will vary, according to bolt material and

size, as well as the material being bolted. Choose the length of tightening time

accordingly.

Reference values are provided below.

(They may vary according to tightening conditions.)

Factors Affecting Tightening Torque

The tightening torque is affected by a wide variety of factors including the follow-

ings. After tightening, always check the torque with a torque wrench.

1) Voltage

When the battery pack becomes nearly discharged, the voltage decreases and

the tightening torque drops.

Bolt Tightening Conditions

(Bolt size : Millimeters)

Tightening time (Sec.)

Tightening torque

M6, M8, M10, M12 x 25 mm (1") Standard bolt

M10 x 25 mm High tensile bolt

M10 x 25 High tensile bolt

9.8

(100)

19.6

(200)

29.4

(300)

39.2

(400)

49.0

(500)

58.8

(600)

68.6

(700)

78.5

(800)

88.3

(900)

M12

M10

0.1 0.25 0.5 1.0 2.0 3.0 4.0

N·m

(k f-cm)



 

 

   





Tightening conditions

* The following bolts are used.

Standard bolt: Strength type 4.8

High tensile type 12.9

Explanation of the strength type

4.8

Bolt tensile strength 588 N/mm2

(60 k f/mm2)

Bolt yield point

(80% of tensile strength)

471 N/mm2(48 k f/mm2)

2) Tightening time

Longer tightening time results

in increased tightening torque.

Excessive tightening, however,

adds no value and reduces the life

of the tool.

3) Different bolt diameters

The size of the bolt diameter

affects the tightening torque.

Generally, as the bolt diameter

increases, tightening torque rises

4) Tightening conditions

Tightening torque will vary, even

with the same bolt, according to

grade, length, and torque coef-

ficient (the fixed coefficient indi-

cated by the manufacturer upon

production).

Tightening torque will vary , even

with the same bolting material

(e.g. steel), according to the sur-

face finish.

Torque is greatly reduced when

the bolt and nut start turning

together.

5) Socket play

Torque is lowered as the six-sided

configuration of the socket of the

wrong size is used to tighten a bolt.

6) Switch (Variable speed control trig-

ger)

Torque is lowered if the unit is used

with the switch not fully pulled out.

7) Effect of Connecting Adaptor

The tightening torque will be low-

ered through the use of a universal

joint or a connecting adaptor.

.ACCESSORIES

ACCESSORIES

Use only bits suitable for size of drill.

MAXIMUM RECOMMENDED CAPACITIES

Model EY6506

Screw

driving

Wood screw ø 5.8 mm (7/32") ±75 mm (3") Yellow pine

Self-drilling screw ø 4.0 mm (5/32") ±13 mm (1/2") SPC t = 1.6 mm (1/16")

Bolt fastening Standard bolt : M12

High tensile bolt : M10

. SPECIFICATIONS

SPECIFICATIONS

MAIN UNIT

Model EY6506

Motor DC Motor 12 V

No load speed 0 ~ 2800 /min (rpm)

Maximum torque 98.0 Nm, (1000 k f-cm, 867 in-lbs)

Impact per minute 0 ~ 3000 ipm in Impact Mode

Overall length 155 mm (6-1/8")

Weight (with battery pack) 1.45 k , (3.2 lbs)

BATTERY PACK

Model EY9200

Storage battery Ni-MH Battery

Battery voltage 12V DC (1.2V × 10 cells)

BATTERY CHARGER

Model EY0110

Electrical rating See the rating plate on the bottom of the charger.

Weight 0.78 k ,(1.72 lbs.)

Charging time

7.2V 9.6 V 12V 15.6V 18V 24V

1.2Ah

EY9065

EY9066

EY9080

EY9086

EY9001

EY9006

20min.

1.7Ah

EY9180

EY9182 EY9101

25min.

2.0Ah EY9168 EY9106 EY9136 EY9117

30min. 30min. 60min.

3.0Ah EY9200 EY9230 EY9210

45min. 90min.

3.5Ah EY9201 EY9231 EY9251

55min. 65min.

NOTE: This chart may include models that are not available in your area.

Please refer to the catalogue.

ONLY FOR U. K.

ELECTRICAL PLUG

INFORMATION

FOR YOUR SAFETY PLEASE READ

THE FOLLOWING TEXT CAREFULLY

This appliance is supplied with a moulded

three pin mains plug for your safety and

convenience.

A 3 amp fuse is ﬁtted in this plug.

Should the fuse need to be replaced please

ensure that the replacement fuse has a

rating of 3 amp and that it is approved by

ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI

mark on the body of the fuse.

If the plug contains a removable fuse cover

you must ensure that it is reﬁtted when the

fuse is replaced.

If you lose the fuse cover the plug must not

be used until a replacement cover is ob-

tained.

A replacement fuse cover can be pur-

chased from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS

UNSUITABLE FOR THE SOCKET OUT-

LET IN YOUR HOME THEN THE FUSE

SHOULD BE REMOVED AND THE PLUG

CUT OFF AND DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE

ELECTRICAL SHOCK IF THE CUT OFF

PLUG IS INSERTED INTO ANY 13 AMP

SOCKET.

If a new plug is to be ﬁtted please observe

the wiring code as shown below.

If in any doubt please consult a qualiﬁed

electrician.

IMPORTANT:

The wires in this mains lead are

coloured in accordance with the

following code:

Blue:Neutral

Brown: Live

As the colours of the wire in the mains lead

of this appliance may not correspond with

the coloured markings identifying the termi-

nals in your plug, proceed as follows.

The wire which is coloured BLUE must be

connected to the terminal in the plug which

is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must

be connected to the terminal in the plug

which is marked with the letter L or coloured

RED.

Under no circumstances should either of

these wires be connected to the earth ter-

minal of the three pin plug, marked with the

letter E or the Earth Symbol .

How to replace the fuse: Open the fuse

compartment with a screwdriver and re-

place the fuse and fuse cover if it is remov-

able.

Fuse Cover

This apparatus was produced to BS800.

Autres manuels pour EY-6506

Table des matières

Langues :

Autres manuels Panasonic Moteur à percussion

Panasonic

Panasonic EY-6506 Manuel utilisateur

Panasonic

Panasonic EY7546 Manuel utilisateur

Panasonic

Panasonic EYFLA4AR Manuel utilisateur

Panasonic

Panasonic EY7546LR2S Manuel utilisateur

Panasonic

Panasonic EY7430 Manuel utilisateur

Panasonic

Panasonic EY7540 - IMPACT DRIVER 14.4V Manuel utilisateur

Panasonic

Panasonic EYFLA7A Manuel utilisateur

Panasonic

Panasonic EYFPA1J Manuel utilisateur

Panasonic

Panasonic EY7271 Manuel utilisateur

Panasonic

Panasonic EY75A1 Manuel utilisateur

Panasonic

Panasonic EY7541 - CORDLESS IMPACT WRENCH Instructions d'utilisation

Panasonic

Panasonic EY7542 - CORDLESS IMPACT WRENCH Manuel utilisateur

Panasonic

Panasonic EY7270-X8 Manuel utilisateur

Panasonic

Panasonic EY75A7 Manuel utilisateur

Panasonic

Panasonic EY7201-X8 Manuel utilisateur

Panasonic

Panasonic EY7202-U1 Manuel utilisateur

Panasonic

Panasonic EYFLB1A Manuel utilisateur

Panasonic

Panasonic EY75A7 Manuel utilisateur

Panasonic

Panasonic EYFLA1A - DRILL - MULTI LANGUAGE Manuel utilisateur

Panasonic

Panasonic EY75A1 Manuel utilisateur

Panasonic

Panasonic EY7202 - 12V IMPACT DRIVER Manuel utilisateur

Panasonic

Panasonic EY75A1 Manuel utilisateur

Panasonic

Panasonic EY7201 - 12V IMPACT Manuel utilisateur

Panasonic

Panasonic EYFLA6PR Manuel utilisateur

Manuels Moteur à percussion populaires d'autres marques

stayer

stayer IW500D Manuel utilisateur

Makita

Makita DTD152 Manuel utilisateur

Milwaukee

Milwaukee M12 FID Manuel utilisateur

Grizzly

Grizzly H6140 Manuel utilisateur

Makita

Makita BTW450 Manuel utilisateur

Ozito

Ozito LID-3000 Manuel utilisateur

Astro Pneumatic Tool

Astro Pneumatic Tool 1812 Manuel utilisateur

Greenlee

Greenlee HW3 Manuel utilisateur

Sthor

Sthor 57091 Manuel utilisateur

Makita

Makita DTD145 Manuel utilisateur

Hilti

Hilti SIW 2-A12 Manuel utilisateur

Ryobi

Ryobi R18IW3 Manuel utilisateur

Parkside

Parkside PDSSA 20-Li A1 Manuel utilisateur

Flex

Flex FX1471 Manuel utilisateur

SATA

SATA 51075C Manuel technique

Cembre

Cembre NR-11P Manuel utilisateur

Makita

Makita BTP131RFE Manuel utilisateur

DeWalt

DeWalt XR Li-ion DCF902 Manuel utilisateur