Panasonic AAD03011 Manuel utilisateur

panasonic-electric-works.net/sunx

Elevator Door Controller AAD03011 Instruction Manual

8A3 708 0000 3

Panasonic Electric Works SUNX Shanghai

©Panasonic Electric Works SUNX Co., Ltd. 2010

8A3 708 0000 3

PRINTED IN CHINA

Panasonic Electric Works SUNX Shanghai Co., Ltd.

http://panasonic-electric-works.net/sunx

T52-3, No.1510, Chuanqiao Road, Jinqiao Export Processing Zone,

Pudong New Area, Shanghai, China

Phone: +86-21-5032-3800 FAX: +86-21-5032-3866

Europe Headquarter: Panasonic Electric Works Europe AG

Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany

Phone: +49-8024-648-0

US Headquarter: Panasonic Electric Works Corporation of America

629 Central Avenue New Providence, New Jersey 07974 USA

Phone: +1-908-464-3550

Elevator Door Controller

AAD03011

Instruction Manual

[Support model]

·AAD03011

Read this manual carefully before

attempting to operate the inverter

and store it for further reference.

ATTENTION

The inverter manufactured in our company is only applied to the elevator.

Use this equipment before ensuring the safety and application of the

elevator.

Always take safety precautions such as dual safety mechanism and

malfunction protection.

Failure to do so could lead to serious accident.

! Caution

Note

Foreword

Safety Precautions

This manual introduces the usage and precautions. Read the manual

carefully before using the product.

Precautions prescribed in this manual is divided into two grades:

Caution and Note.

The dangerous situations that could lead to moderate

or slight personal injury or property damage by

mishandling the equipment.

In addition, the precautions prescribed in Caution may lead to

serious situations in different conditions.

Please follow the information and instructions as laid out in this

manual carefully to avoid damage to equipment or risk to personal

injury.

The dangerous situations that could lead to personal

injury or death by mishandling the equipment.

Read this manual and related documents before attempting to install,

operate, service or inspect the inverter.

Make sure that you have an understanding of the device, the safety

information and all precautions before starting use.

Thank you for purchasing the AAD03011 inverter produced by Panasonic

Electric Works SUNX Shanghai Co., Ltd.

Note

1. Installation

2. Wiring

!Caution

Install the unit on a non-combustible material such as metal.

Installing it on other material could lead to fires.

Do not place the unit near flammable materials.

Doing so could lead to fires.

Do not hold by terminal cover during transportation.

Doing so could cause the unit to drop and lead to injuries.

Do not allow foreign matter such as metal swarf enter the unit.

Entry of this type of matter could lead to fires.

Install the unit according to the instruction manual on a place

where the weight can be withstood.

Failure to do so could lead to dropping of the unit and to injuries.

Do not install or operate an inverter that is damaged or missing parts.

Doing so could lead to injuries.

Always confirm that the input power is OFF before starting wiring.

Wait at least five minutes after turning the input power OFF before

starting use.

Failure to do so could lead to electric shocks or injuries.

Always connect the earth.

Failure to do so could lead to electric shocks or fires.

Wiring work must be carried out by a qualified technician.

Failure to do so could lead to electric shocks or fires.

Always install the unit before wiring.

Failure to do so could lead to electric shocks or injuries.

Note

!Caution

3. Operation

Do not connect an AC power supply to the output terminals (U, V, W).

Doing so could lead to injuries or fire.

Connect the correct wiring for the motor. If the wiring is incorrect,

the door control cannot operate properly.

Failure to do so could lead to injuries.

Connect the control terminals correctly. If the wiring is incorrect,

the door control cannot operate properly.

Failure to do so could lead to injuries.

Confirm that the product's rated voltage and the AC power supply

voltage match.

Failure to do so could lead to injuries or fire.

Tighten the terminal screws with the designated tool.

Failure to do so could lead to fire.

Always close the terminal cover before turning the input power ON.

Do not open the terminal cover while the power is ON.

Doing so could lead to electric shock.

Do not operate the buttons with wet hands.

Doing so could lead to electric shock.

Do not touch the inverter terminals when the inverter power is

ON or even when the inverter is stopped.

Doing so could lead to electric shock.

The STOP button is not designed for emergency stop purposes.

Prepare a separate emergency stop switches.

Failure to do so could lead to injury.

䋴

䈀㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷䈁

Always confirm the security and function operation of the elevator

before obstacle detection function is applied.

Failure to do so could lead to injury.

Make sure to input safety sensor in the main controller of the elevator

and to operate the door's obstacle detection on the main controller side.

Obstacle detection function of the inverter does not operate in

CLOSE arrival area.

Always take dual security measures.

Failure to do so could lead to injury.

Make sure to input arrival signal (limit switch etc.)in the main controller

of the elevator and to operate the door's obstacle detection on the

main controller side.

Do not operate obstacle detection of the door only with OPEN/

CLOSE arrival signal (input signal and the relay's output signal).

Failure to do so could lead to injury.

Depending on different settings of the fault OPEN operation forced

operation time and the stop selection of OPEN/CLOSE operation,

sometimes even OPEN/ CLOSE signal are both turned OFF, the door

does not stop.

Confirm the elevator's security and function operation before using

this equipment.

(Secure personal safety before carrying out the operation.)

Failure to do so could lead to injury.

Depending on settings of the start mode and ride-through function

settings, if the run signal is ON or the power is restored after a power

failure, the inverter may start (restart) suddenly. Keep out of the working

part of the motor and the machine.

Design the machine so that personal safety can

be ensured even if the inverter starts suddenly.

Failure to so could lead to injury.

Depending on the start mode function setting, if "the fault trip is reset"

or "the stop state is released with the panel STOP function" or

"door width measurement is reset" when the run signal is input,

the inverter may restart suddenly.

(Secure personal safety before using this function.)

Failure to do so could lead to injury.

When the retry function is used, the inverter may automatically start(restart)

suddenly. Keep out of the working part of the motor and the machine.

(Secure personal safety before using this function.)

Failure to so could lead to injury.

4. Maintenance, Inspection and Part Replacement

Note

!Caution

The heat sink fins and brake resistor can reach high temperatures,

so do not touch them. Doing so could lead to burns.Ǆ

The inverter can be easily set to run from low speeds to high speeds.

Confirm the tolerable range of the motor and machine before starting

operation.

Failure to do so could lead to injure.

Prepare holding brakes if required.

Failure to do so could lead to injure.

If there is no arrival signal, start operation before ensuring the

security and function operation of the elevator system.

(Secure personal safety before starting operation.)

Failure to do so could lead to injury.

When carrying out the door repeat control and the door width

measurement, the operation direction of the door may change

automatically. Start operation after ensuring personal safety.

Failure to do so could lead to injury.

Adjust and confirm each parameter before operating. Depending

on the settings of the parameters, the inverter may work unexpectedly.

Failure to do so could lead to injure.

Wait at least five minutes after turning the input power OFF before

starting inspections.

Failure to do so could lead to electric shock.

Maintenance, inspection and part replacement must be done by

qualified persons. [Remove all metal personal belongings

(watches, bracelets, etc.) before starting the work. ]

(Use tools treated with insulation.)

Failure to do so could lead to electric shocks or injury.

6. General Precautions

5. Others

Do not use the inverter for a load other than a three-phase

induction motor.

Never disassemble or modify the inverter. Doing so could lead

to electric shock or injury.

200V 0.4kW

WARNING

ELECTEIC SHOCK RISK˗

䃂

Disconnect supply and wait

䋵minutes before working on

this equipment.

䋣

7. Warning Lable on Inverter

[Inverter Surface]

Note

Caution

Have an electrician periodically tighten the terminal screws.

Loosening of the terminal screws could lead to overheating or fire.

All diagrams in this instruction manual show the state with the cover

or safety partitions removed to explain the details. Before operating

the product, replace the covers and partitions to the positions specified,

and operate the unit according to the instruction manual.

Table of Contents

Special Precautions 9䊶10

Installation 11

䇶Page䇷

Outline Dimensions 12

Parts Identification 13䌾15

Wiring (Main Circuit) 16䊶17

Wiring(Control Circuit) 18䌾22

Operation(Basic Operation) 23䌾28

Function of each modes 29䌾33

Setting and Changing Function 34䊶35

Functional Descriptions (Parameter Table) 36䌾40

Functional Descriptions (By parameters) 41䌾73

Operation procedure of Custom mode 74䌾75

Resetting Fault Trips 90

Troubleshooting 㽲91

Troubleshooting 㽳92

Maintenance and Inspection 93䊶94

Specifications 95䌾97

Supplementary Explanation of Door

Width Measurement

Supplementary Explanation of Obstacle

Detection Function of the Door

Supplementary Explanation of

Communication Function

78䌾88

Individual Details and Remedies for

Fault Trips

89䊶90

Points for Handling

Follow this manual and precautions when handling the inverter.

Incorrect handling could lead to inhibited operation or a drop operating

life. In the worst case, the inverter could be damaged.

Power supply Use within + 10%, -15% of the tolerable input

voltage range, and within 㫧5% of the tolerable

input frequency range.

Circuit breaker

MCCB

Size a breaker from the selection table on page 17.

Magnet

contactor

MC

A magnet contactor is not required in normal

use. If installed, do not start or stop the inverter

with the magnet contactor.

Power factor

improvement

reactor

Connect this when the power factor must be

improved.

Input noise

filter

Connect this when noise to the peripheral

devices is a problem.

N䊶F

Inverter The ambient temperature is the most important

factor for the installation site. Make sure that the

tolerable value is not exceeded.

(See page 9 and 11)

Thermal relay

for open phase

protection

The thermal component built into the inverter is

used to protect against overloads. Use an open

phase protection thermal relay for open phase

protection.

Motor 3-phase induction motor.

Table des matières

Autres manuels Panasonic Contrôleurs

Panasonic

Panasonic CZ-RD517C Manuel utilisateur

Panasonic

Panasonic EYFLA7AR Mode d'emploi

Panasonic

Panasonic FPS Series Manuel utilisateur

Panasonic

Panasonic CZ-64ESMC2 Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Panasonic

Panasonic FP Series Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Panasonic

Panasonic FP3 Manuel utilisateur

Panasonic

Panasonic SG-PK-M Series Manuel utilisateur

Panasonic

Panasonic SL-VGU1-C Manuel utilisateur

Panasonic

Panasonic AKHRP900P - CAMERA CONTROLLER HC Manuel utilisateur

Panasonic

Panasonic AKHRP900P - CAMERA CONTROLLER HC Manuel utilisateur

Panasonic

Panasonic CZ-ANC2 Manuel utilisateur

Panasonic

Panasonic CZ-ANC2 Manuel utilisateur

Panasonic

Panasonic fp2/fp2sh Manuel utilisateur

Panasonic

Panasonic FP-I4C Manuel utilisateur

Panasonic

Panasonic FP Web-Server2 Manuel utilisateur

Panasonic

Panasonic CZ-RD516C-1 Manuel utilisateur

Panasonic

Panasonic FV-SW20VEC1 Manuel utilisateur

Panasonic

Panasonic FP7 Series Manuel utilisateur

Panasonic

Panasonic FP7 Series Manuel utilisateur

Panasonic

Panasonic SQ4-C11 Manuel utilisateur

Panasonic

Panasonic Programmable Controllers FP-X Series Manuel utilisateur

Panasonic

Panasonic FP7 Series Manuel de la liste des pièces

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur

3M MicroTouch EX113 Manuel utilisateur

KUHN

KUHN TKS Manuel utilisateur