Panasonic WJ-ND400K Manuel utilisateur

LCD

[ESC] button

[SET] button

Arrow buttons

Quick Reference Guide

The Quick Reference Guide provides simple explanations of how to operate this recorder.

■Network settings

Configure the network settings such as the IP address, subnet mask, etc. for each port.

Item Camera port

[PT#1]

Client PC port

[PT#2]

Maintenance port

[PT#3]

DHCP _OFF _

IP address 192.168.0.250 192.168.1.250 192.168.2.250

Subnet mask 255.255.255.0 255.255.255.0 255.255.255.0

Default gateway _192.168.1.1 _

HTTP port _80 _

●Default network settings

Network Disk Recorder

WJ-ND400K, WJ-ND400K/G

●IP address setup display ●How to configure the network settings

Repeat pressing the arrow button (up

or down) until the "IP Address Setup"

indication is displayed. When the "IP

Address Setup" indication is displayed,

press the [SET] button.

 • Thecurrentselectedsetupitemor

a value will be indicated by the

underscore mark "_".

→The setup window will be displayed.

 • Whentheunderscoremark"_"is

below the ">" indication,

Arrow button (left or right): Select a

port number

Arrow button (up or down): Select a

setup item

Press the [SET] button while the under-

score mark (_) is displayed below the ">"

indication.

→The underscore mark "_" will move

below a setting value and the

editing of the settings became

enabled.

Move the underscore mark below the

number to be edited.

 • Arrowbutton(leftorright):Movethe

underscore mark "_"

 • Arrowbutton(upordown):Entera

value

To determine the edited setting, move

the underscore mark below the ">" indi-

cation by pressing the [ESC] button.

To display the time and date display

(standby display) again, press the [ESC]

button again.

■Display the operation window

Display the operation window using a web browser installed on a PC.

Launch a web browser. After the web

browser starts, enter the IP address set

to this recorder in the address box, and

press the enter key.

→The user authentication window will

be displayed.

Enter the registered user name and

password to log in to the recorder.

 • Default

User name: ADMIN

Password: 12345

Click the [login] button.

→The top page of the operation window

will be displayed.

 • Whenthetoppageisdisplayedfor

the first time, the install wizard of the

ActiveX control will be displayed.

Follow the instructions of the wizard.

[SET]

■User interface on the operation window

w e r t

q [Control] button: Search and play recorded images,

switch the camera channels, etc.

w [Cam. Select] button: Select the camera channel from

which images are to be displayed.

e [Setup] button: Configure the settings of the recorder.

r Status display area: The status of the recorder such as

the recording status, playback status, etc. will be displayed.

t Current time display area: The current time will be dis-

played.

y Image display area: Live images/recorded images will be

displayed.

u Playback point operation area: Designate a point to be

played or play the latest recorded image.

i [HDD] tab: Control playback operation.

o [CAM] tab: Control the camera operation (zoom, focus,

auto function, etc.).

■Basic settings

Configure the minimum required settings to operate the recorder.

Click the [Setup] button, and then click

the [Quick] button.

Set the current time and date.

Click the [Set] button just below the

"Time & date" setting.

→The "Quick" page will be displayed.

1. Set the current time

2. Register cameras

Select a port to which cameras are

connected to detect them.

→Select the camera port or the client

PC port.

Determine how to assign and register

an IP address of the detected camera.

→Select [Register the IP address

automatically given by this unit to a

detected camera] or [Register the

IP address set with a detected

camera].

Click the [Registration] button, and then

click the [OK] button.

→The "Camera registration result"

window will be displayed after the

registration is complete.

Check the registration results, and then

click the [OK] button.

→Up to 64 cameras can be registered.

 • Whenthedesiredcameraisnot

detected or when the settings of a

camera are required to be

changed, configure the settings on

the "NW camera" page.

3. Program

When the camera registration is com-

plete, the recording rate for the live

image transmission and manual record-

ing on the "Program" page will automati-

cally be set to "1 ips".

Click the [Display] button to check the

detailed settings of "Program".

➜➜

Click the [Cam. Select] button. →A list of the registered cameras will

be displayed in the [Cam. Select]

box.

Click the "WJ-ND400" icon, the group

title and the camera title in order.

→Live images from the selected cam-

era channel will be displayed on a

1-screen.

Click the [Multiscreen select] button. →Live images from the cameras (regis-

tered as a group) will be displayed on

a 4-screen.

 • Eachtimethe[Multiscreenselect]

button is clicked, live images from

the registered camera groups will be

displayed.

■Monitor live images

Display live images on a 1-screen or on a 4-screen (multiscreen).

Click the [Cam. Select] button, and then

click the [Sequence] button.

→Live images from the cameras will

be displayed sequentially.

 • Theindicatoronthe[Sequence]

button will light green and the "SEQ"

indication will be displayed in the

status display area.

Click the [Sequence] button again. →The indicator on the [Sequence]

button will go off and the sequential

display of live images will stop.

Display live images from the cameras sequentially (sequential display).

■Control cameras

It is possible to operate cameras with the panning/tilting function on the [CAM] tab.

Click the [▲] button in the [REC] box on

the [HDD] tab.

→Repeat clicking the [▲] button until

the [Recording] button and the

[Recording stop] button are dis-

played.

Click the recording button (red). →Recording will start and the [REC]

indicator in the status display area

will light red.

Click the recording stop button

(yellow).

→Recording will stop and the [REC]

indicator in the status display area

will disappear.

q [Zoom]: Zoom in/out the displayed image.

w [Focus]: Adjust the focus point.

e [Auto mode]: Activate the designated auto function of the camera.

r Control buttons: Adjust the camera direction.

Control pad: Panning/tilting speed will be faster if a clicked point

gets farther from the center point of the control pad.

t [Brightness]: Adjust the lens iris (brightness).

y [Preset]: Move the camera to the registered preset position.

■Manual recording

It is possible to record images manually.

[CAM] tab

q e r t

Select the desired camera channel, and

then click the [PLAY] button.

→Playback of recorded images will

start.

The indication will be displayed

in the status display area.

 • Playbackwillresumefromtheend

point (time and date) of the last

playback.

To stop playback, click the [STOP] but-

ton.

→The indication will disappear and

live images from the camera will be

displayed.

Click the [Go to date] button on the

playback point operation area.

→The "Go to date" window will be dis-

played.

Click the [Control] button, and then click the [Search] button in the

[Search] box.

 • The"Selectsearchmethod"windowwillbedisplayed.

Click the [REC event search] button.

 • The"RECeventsearch"windowwillbedisplayed.

Narrow the search by selecting the recording event type.

Designate the time range ("Start" and "End" of "Time & date"),

"Rec event" and "Camera" to filter the search and then click the

[OK] button.

 • The"FILTERING"indicationwillbedisplayedinthestatus

display area, and then the search results will be displayed

on the list display area.

 • Clickthe[Alllist]buttontocanceltostartsearching.

■Play recorded images

Itispossibletoplayrecordedimages.

■Search and play recorded images

Itispossibletosearchandplayrecordedevents(RECeventsearch).

Select the time and date by clicking the

[V] button, and then click the [Play] but-

ton.

→Playback of the corresponding

recorded images will start and the

indication will be displayed in the

status display area.

Itispossibletoperformplaybackoperationonthe[HDD]tab.

Each time the button is clicked, the playback speed will change as

follows.

(Approx. 4x →8x →16x →32x →48x →96x)

w [NEXT RECORD]/[PREV RECORD]: Skip to the next or previous

recorded image and play it.

e [NEXT IMAGE]/[PREV IMAGE]: Display the next or previous frame

when this button is clicked during playback/pausing.

q [FF]/[REW]: Perform fast playback or fast reverse playback. [HDD] Tab

Click the time & date of the desired recording event. Playback

of recorded images corresponding to the selected recording

event will start.

To stop playback, click the [STOP] button.

Playback point

operation area

Nd0811-0 3TU001890BDA Printed in China

Autres manuels pour WJ-ND400K

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panasonic Lecteur CD

Panasonic

Panasonic CQDF802U - AUTO RADIO/CD DECK Manuel utilisateur

Panasonic

Panasonic CQ-DP151W Manuel utilisateur

Panasonic

Panasonic SL-SV600J Manuel utilisateur

Panasonic

Panasonic SL-SX445EG Manuel utilisateur

Panasonic

Panasonic SL-SX287J Manuel utilisateur

Panasonic

Panasonic LX-200EN Manuel utilisateur

Panasonic

Panasonic SL-MP353J Manuel utilisateur

Panasonic

Panasonic SL-CT582V Manuel utilisateur

Panasonic

Panasonic SL-SV500 Manuel utilisateur

Panasonic

Panasonic SL-SX240 Manuel utilisateur

Panasonic

Panasonic SL-SX332 Manuel utilisateur

Panasonic

Panasonic CQ-DF202W Manuel utilisateur

Panasonic

Panasonic CQ-DFX683N Manuel utilisateur

Panasonic

Panasonic WJ-ND400/1000 Manuel utilisateur

Panasonic

Panasonic PalmTheater DVD-L50D Manuel utilisateur

Panasonic

Panasonic SLPS770D - COMPACT DISC PLAYER Manuel utilisateur

Panasonic

Panasonic SL-SX287J Manuel utilisateur

Panasonic

Panasonic WJDR200 - DIGITAL VIDEO RECORD Manuel utilisateur

Panasonic

Panasonic SL-CT790 Manuel utilisateur

Panasonic

Panasonic WJ-NX200K Manuel d'utilisation

Panasonic

Panasonic SL-S120 Manuel utilisateur

Panasonic

Panasonic WJ-HD88 Manuel utilisateur

Panasonic

Panasonic SLSX330 - PORTABLE CD PLAYER Manuel utilisateur

Panasonic

Panasonic SL-PD349 Manuel utilisateur

Manuels Lecteur CD populaires d'autres marques

RCA

RCA RP-7923 Manuel utilisateur

Pioneer

Pioneer DEH-P3550MP XM Manuel utilisateur

Philips

Philips AZ1207 Manuel utilisateur

Philips

Philips CD582 Manuel utilisateur

Philips

Philips AZ 6821 Manuel utilisateur

Lasonic

Lasonic MSU-2020 Manuel utilisateur

THOMSON

THOMSON RCD150 Manuel utilisateur

Denon

Denon DCD-1420 Manuel utilisateur

Onkyo

Onkyo DX-7210 Manuel utilisateur

Sony

Sony MZ-R3 Manuel utilisateur

Denon

Denon DVM-4800 Manuel utilisateur

JBL

JBL MR-32 Manuel utilisateur

RCA

RCA RCD152 Manuel utilisateur

Technics

Technics SL-PS770A Manuel utilisateur

Clarion

Clarion compact disc Manuel utilisateur

Sony

Sony MZ-M10 Manuel utilisateur

Philips

Philips Expanium AZ 1538 Manuel utilisateur

Rotel

Rotel RCD 975 Manuel utilisateur