Panasonic SL-SV590EG Manuel utilisateur
© 2006 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and distribu-
tion is a violation of law.
ORDER NO. AD0604011CE
Portable CD Player
SL-SV590EB
SL-SV590EG
SL-SV590GC
SL-SV590GN
SL-SV590GT
Colour
(S)...........Silver Type
2
TABLE OF CONTENTS PAGE PAGE
1 Safety Precaution-------------------------------------------------3
1.1. Precaution of Laser Diode -------------------------------3
1.2. Handling Precautions for Traverse Deck-------------4
2 Service Navigation------------------------------------------------5
2.1. General Description About Lead Free Solder
(PbF) ----------------------------------------------------------5
3 Specifications------------------------------------------------------6
4 Location of Controls and Components--------------------7
4.1. Accessories--------------------------------------------------7
4.2. Location of Controls ---------------------------------------7
5 Service Mode-------------------------------------------------------7
5.1. Display of Self-Diagnostic Function -------------------7
6 Troubleshooting Guide------------------------------------------8
6.1. Checking the Operation Problems on the
Traverse Deck (Optical Pick-up) -----------------------8
7 Disassembly and Assembly Instructions-----------------9
7.1. Checking for the PCB-------------------------------------9
7.2. Replacement for the traverse motor----------------- 11
7.3. Replacement for the optical pick-up----------------- 11
7.4. Replacement for the rest switch----------------------13
8 Measurements and Adjustments --------------------------14
8.1. Automatic Adjustment Results Display
Function (Self-Check Function) ----------------------14
3
1 Safety Precaution
1.1. Precaution of Laser Diode
•For SL-SV590EB/EG
•For SL-SV590GC/GN/GT
Caution:
This product utilizes a laser diode with the unit turned on, invisible laser radiation is emitted from the pick-up lens.
Wavelength: 795 nm
Maximum output radiation power from pick-up: 100 μW/VDE
Laser radiation from the pick-up lens is safety level, but be sure the followings:
1. Do not disassemble the optical pick-up unit, since radiation from exposed laser diode is dangerous.
2. Do not adjust the variable resistor on the pick-up unit. It was already adjusted.
3. Do not look at the focus lens using optical instruments.
4. Recommend not to look at pick-up lens for a long time.
4
1.2. Handling Precautions for Traverse Deck
The laser diode in the traverse deck (optical pick-up) may break
down due to potential difference caused by static electricity of
clothes or human body.
So, be careful of electrostatic breakdown during repair of the
traverse deck (optical pick-up).
1.2.1. Handling of Traverse deck
(optical pick-up)
1. Do not subject the optical pick-up to static electricity as it
is extremely sensitive to electrical shock.
2. To protect the laser diode against electrostatic break-
down, be sure that the short land of the flexible board
(FFC board) should be short-circuit by solder before pull-
ing out the FFC. Then inserting a short pin or similar
object into the tip of the flexible board.
(Refer to Fig. TR1)
3. Take care not to apply excessive stress to the flexible
board (FFC board).
4. Do not turn the variable resistor (laser power adjustment).
It has already been adjusted. (Refer to Fig. TR1)
Fig. TR1
1.2.2. Caution when replacing traverse
deck
The new traverse deck short-circuits by the short pin, the foil
(B) and short lands to protect the laser diode against electro-
static breakdown. Be sure to replace to new one following pro-
cedures.
1. Remove the short pin from the FFC, and then connect it
to the connector.
2. Cut the foil (B). (Refer to Fig. TR1) (Take care not to
make contact with cutting point each other.)
3. Unsolder the short lands. (Refer to Fig. TR1)
1.2.3. Ground for electrostatic breakdown
prevebtion
1.2.3.1. Human body grounding
Use the anti-static wrist strap to discharge the static electricity
from your body. (Refer to Fig. TR2)
Fig. TR2
1.2.3.2. Work table grounding
Put a conductive material (sheet) or steel sheet on the area
where the traverse deck (optical pick-up) is placed, and ground
the sheet. (Refer to Fig. TR3)
Fig. TR3
Caution:
The static electricity of your clothes will not be grounded
through the wrist strap.
So take care not to let your clothes touch the traverse deck
(optical pick-up).
5
2 Service Navigation
2.1. General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C more than that of the normal
solder.
Distinction of PCB Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C .
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
6
3 Specifications
7
4 Location of Controls and Components
4.1. Accessories
• AC adaptor
For EB (N0JCCE000004)..............................1 pc.
For EG (RFEA418E-2S)................................1 pc.
For GC (RFEA447Z-S)..................................1 pc.
For GT (RFEA439G-U).................................1 pc.
For GN (RFEA446A-S)..................................1 pc.
• Stereo earphones
(L0BAB0000182)...........................................1 pc.
• Power plug adaptor (Only GC)
(K2DA42E00001)...........................................1 pc.
4.2. Location of Controls
5 Service Mode
5.1. Display of Self-Diagnostic Function
This unit (SL-SV590) has self-diagnostic function. It may display below-mentioned on the LCD of this unit.
• The substance of self-diagnostic display.
LCD display
(Press PLAY and STOP button. After 15 seconds, it is displayed for 2 seconds.)
In case of this display, it may be causing for abnormally movements of traverse deck, touching failure of REST detect switch and
coming off or cutting off the flexible PCB. It is necessary for confirmation or repair and replacement each parts.
Open
Play/Pause
VOL
HOLD
Stop/Turn off
Skip/Search Volume control
Headphone jack
Hold
Slider
Earphones
Battery lid Lens
Memory/Antiskip
Equalizer
Mode
Radio
FM MONO/ST
CITY/NOR
LCD display
8
6 Troubleshooting Guide
6.1. Checking the Operation Problems on the Traverse Deck
(Optical Pick-up)
Make sure to follow the procedures below to check the operation problems of the traverse deck (optical pick-up) before replacing it.
Replace the traverse deck only after the problem is identified.
6.1.1. Check the operations described below on the traverse deck after
replacing
6.1.1.1. Checking skip search
1. Play an ordinary musical program disc.
2. Press the skip button to check for normal skip search
operation (in both the forward and reverse directions).
6.1.1.2. Checking manual search
1. Play an ordinary musical program disc.
2. Press the manual search button to check for smooth
manual search operation at either low or high speed (in
both the forward and reverse directions).
6.1.1.3. Checking playability
1. Play the 0.7 mm black dot and the 0.7 mm wedge on the
playability test disc (SZZP1054C) and verify that no
sound skip or noise occurs.
2. Play the middle tracks of the uneven test disc
(SZZP1056C) and verify that no sound skip or noise
occurs.
9
7 Disassembly and Assembly Instructions
•This section describes procedures for checking the
operation of the major printed circuit boards and replac-
ing the main components.
•For reassembly after operation checks or replacement,
reverse the respective procedures. Special reassembly
procedures are described only when required.
7.1. Checking for the PCB
7.1.1. Checking for the PCB (A side)
•Check the PCB (A side) as shown below.
10
7.1.2. Checking for the PCB (B side)
• Follow the (Step 1) - (Step 7) of item 7.1.1. •Check the PCB (B side) as shown below.
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Panasonic Lecteur CD
Panasonic
Panasonic SL-CT350 Manuel utilisateur
Panasonic
Panasonic CQ-C5400 Manuel utilisateur
Panasonic
Panasonic SL-CT345 Manuel utilisateur
Panasonic
Panasonic SL-SX445 Manuel utilisateur
Panasonic
Panasonic SL-S355 Manuel utilisateur
Panasonic
Panasonic CQ-DP738 Manuel utilisateur
Panasonic
Panasonic DVD-PV55 Manuel utilisateur
Panasonic
Panasonic CX-DP880U - CD Changer Manuel utilisateur
Panasonic
Panasonic SLCT570 - PORT. CD PLAYER Manuel utilisateur
Panasonic
Panasonic SL-PD349 Manuel utilisateur
Panasonic
Panasonic LX-200EN Manuel utilisateur
Panasonic
Panasonic DVD-LX110EE Manuel utilisateur
Panasonic
Panasonic SL-J610V Manuel utilisateur
Panasonic
Panasonic SL-SW947S Manuel utilisateur
Panasonic
Panasonic SL-S650 Manuel utilisateur
Panasonic
Panasonic LX-900 Manuel utilisateur
Panasonic
Panasonic SL-S292 Manuel utilisateur
Panasonic
Panasonic SL-SX460 Manuel utilisateur
Panasonic
Panasonic SJ-MR220 Manuel utilisateur
Panasonic
Panasonic SLSX430 - PORTABLE CD PLAYER Manuel utilisateur
