PalmMicro PA168V Manuel utilisateur
PA168V H323 FXS Gateway Telnet Setup Guide (V1.60)
PA168V H323 FXS Gateway
Telnet Setup Guide
¾
Telnet Configuration ........................................................................................................ 2
¾
PA168V Telnet Commands Explanation ...................................................................... 2
¾
Command ? ................................................................................................................... 3
¾
Command get .................................................................................................................. 4
¾
Command set................................................................................................................... 6
¾
Command store ............................................................................................................. 18
¾
Command load .............................................................................................................. 18
¾
Command default .......................................................................................................... 19
¾
Command exit................................................................................................................ 19
¾
Command write.............................................................................................................. 19
PA168V H323 FXS Gateway Telnet Setup Guide (V1.60)
2
When PA168V H323 FXS gateway is properly installed, you can set each
parameter through PC and Telnet commands.
Details please refter to 《PA168V H323 FXS gateway Spec and Install》
¾Telnet Configuration
●On the PC choose Start>Run, type telnet 192.168.1.100 into Run field
in popuping Run dialog. Or input telnet 192.168.1.100 in the DOS
window. Then the following information will be displayed.
PA168X V1.60 settings
Password :
Then please type password. With debug set as 0[disable], if you type ordinary
password (default one is 1234), after Retun, you will see：
Password : ****
P:\>
If you type super password, then you will see:
Password : ********
P:\>
The above information indicates that PA168V FXS gateway is under setting
mode, and then you can set the PA168V FXS gateway by using the telnet
commands.
¾PA168V Telnet Commands Explanation
Command Function
PA168V H323 FXS Gateway Telnet Setup Guide (V1.60)
3
? Supply command name and parameters
get Display basic parameters of the PA168V FXS gateway
set Set parameters of the PA168V FXS gateway
store Save current settings to designated position
load Load designated settings to current position
default Restore to manufactory defaults parameters
exit Exit from the setting mode without saving the configuration
write Exit with saving all configurations and restart PA168V
¾Command ?
Syntax description: No optional parameter
Usage: Type command name and parameters by following P:\> . Be
used as the keyword to supply keyword and parameters of the relevant
commands.
Relevant usage: None
Detailed description:
？List help of all commands
For example:
P:\>?
set
get listsettings
store x store current to xth settings
load x load xth settings to current
default
exit
write save settings
PA168V H323 FXS Gateway Telnet Setup Guide (V1.60)
4
¾Command get
Syntax description: No optional parameter of keywords
Usage: Display basic parameters of the PA168V FXS gateway
Relevant usage: None
Detailed description:
get Display basic running parameters of the PA168V FXS
gateway. Input ordinary password without debug being set as 0[disable],
or input super password with debug set as 0[disable], then following
parameters of PA168V FXS gateway will be displayed:
PA168X V1.60 settings
Password: ********
P:\>get
***************Network Settings***************
iptype 0[static]
ip 192.168.1.100 subnetmask 255.255.255.0 router 192.168.1.254
dns 202.106.46.151 dns2 202.96.128.68 mac 00-0d-ea-00-00-03
***************Audio Settings***************
codec1 0[g729] codec2 3[g711a] codec3 2[g711u]
codec4 4[gsm] codec5 6[null] codec6 6[null]
vad 1[enable] agc 0[disable] aec 1[enable]
audioframes2 6.3k1[enable] ilbcpayload98
jittersize0 handsetin15 handsetout20
dualmode 1[pstn first] dualmodeprefix 30
***************Dial Plan Settings***************
dialplan 1[enable] dddcode 10
iddcode 86 iddprefix 00 dddprefix 0
innerline 1[enable] innerlineprefix 0 callwaiting 1[enable]
fwdnumber 95963 fwdpoweroff 0[disable]
fwdalways 1[enable] fwdbusy 0[disable] fwdnoanswer 0[disable]
digitmap 0[disable]
***************Protocol Settings***************
service 1[enable] registerttl 60
servicetype 0[common] serviceaddr 203.93.9.57
nattraversal 1[enable]
PA168V H323 FXS Gateway Telnet Setup Guide (V1.60)
5
nataddr [www.showmyip.com] natttl 0
phonenumber 82378801 account [empty] pin [empty]
rasport 1732 q931port 1732 h245port 1734
rtpport 1734 tos 0
localtype 0[phonenumber] dtmf 0[inband audio]
***************Other Settings***************
superpassword 12345678 debug 1[output ]
password 1234 upgradetype 0[disable]
upgradeaddr [empty]
sntpip 0.0.0.0 daylight 0[disable]
timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi]
Input ordinary password with debug set as 0[disable], and the following
information will be seen:
PA168X V1.60 settings
Password:****
P:\>get
***************Network Settings***************
iptype 0[static]
ip 192.168.1.100 subnetmask 255.255.255.0 router 192.168.1.254
dns 202.106.46.151 dns2 202.96.128.68 mac 00-0d-ea-00-00-03
***************Audio Settings***************
codec1 0[g729] codec2 3[g711a] codec3 2[g711u]
codec4 4[gsm] codec5 6[null] codec6 6[null]
vad 1[enable] agc 0[disable] aec 1[enable]
audioframes2 6.3k1[enable] ilbcpayload98
jittersize0 handsetin15 handsetout20
dualmode 1[pstn first] dualmodeprefix 30
***************Dial Plan Settings***************
dialplan 1[enable] dddcode 10
iddcode 86 iddprefix 00 dddprefix 0
innerline 1[enable] innerlineprefix 0 callwaiting 1[enable]
fwdnumber 95963 fwdpoweroff 0[disable]
fwdalways 1[enable] fwdbusy 0[disable] fwdnoanswer 0[disable]
digitmap 0[disable]
***************Other Settings***************
password 1234 upgradetype 0[disable]
upgradeaddr [empty]
sntpip 0.0.0.0 daylight 0[disable]
PA168V H323 FXS Gateway Telnet Setup Guide (V1.60)
6
timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi]
¾Command set
Syntax description: set keywords value
Usage: It is to configure password and other running parameters of
PA168V FXS gateway.
Detailed description:
set iptype X
Set how PA168V FXS gateway gets relevant network parameters.
X ranges from 0 through 3. 0: authorize users to set IP address,
subnet mask and router IP address of PA168V manually; 1: use
DHCP mode. With this system, 2: use PPPoE mode. Those ADSL
and Cable Modem users please select this item. 3: use modem
mode. Those who use PA168V with modem please set the value
as 3.
set pppid XXX
With iptype set as 2, use this command to set user name of
PPPoE; with iptype set as 3, use this command to set user name
of dial-up network.
set ppppin XXX
With iptype set as 2, use this command to set user name of
PPPoE; with iptype set as 3, use this command to set user name
PA168V H323 FXS Gateway Telnet Setup Guide (V1.60)
7
of dial-up network.
set ip XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set IP address of
PA168V FXS gateway.
set subnetmask XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set subnet mask of
PA168V FXS gateway.
set router XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set router IP of
network.
set dns XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set IP address of DNS
server.
set dns2 XXX.XXX.XXX.XXX
With iptype set as 0, use this command to set IP of backup DNS
server.
set mac XX-XX-XX-XX-XX-XX
Set MAC address of the PA168V FXS gateway. Parameter
xx-xx-xx-xx-xx-xx must be an HEX number.
set codec1 X
Set the priority 1of the audio compression algorithm. X ranges
PA168V H323 FXS Gateway Telnet Setup Guide (V1.60)
8
from 0 through 6: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm; 5:
ilbc; 6: null.
set codec2 X
Set the priority 2 of the audio compression algorithm. X ranges
from 0 through 6: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm; 5:
ilbc; 6: null.
set codec3 X
Set the priority 3 of the audio compression algorithm. X ranges
from 0 through 6: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm; 5:
ilbc; 6: null.
set codec4 X
Set the priority 4 of the audio compression algorithm. X ranges
from 0 through 6: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm; 5:
ilbc; 6: null.
set codec5 X
Set the priority 5 of the audio compression algorithm. X ranges
from 0 through 6: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm; 5:
ilbc; 6: null.
set codec6 X
Set the priority 6 of the audio compression algorithm. X ranges
from 0 through 6: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm; 5:
ilbc; 6: null.
PA168V H323 FXS Gateway Telnet Setup Guide (V1.60)
9
set vad X
Enable/disable VAD. X ranges from 0 through 1: 0: disable VAD; 1:
enable VAD.
set agc X
Enable/disable AGC. X ranges from 0 through 1: 0: disable AGC; 1:
enable AGC.
set aec X
Enable/disable AEC. X ranges from 0 through 1: 0: disable AEC;
1: disable AEC.
set audioframes X
Set audio frames in RTP package. X is Arabic numerals between 0
and 7.
set 6.3k X
With G.7231 codec selected; set PA168V FXS gateway to use
6.3K rate or not. X ranges from 0 through 1: 0: use 6.3K rate; 1:
use 5.3K rate.
set jittersize X
Set buffer size of RTP package. X ranges from 0 to 32.
set ilbcpayload X
Set the payload type of RTP package whne ILBC codec selected
to DTMF delay.X is range from 96-255.
set handsetin X
PA168V H323 FXS Gateway Telnet Setup Guide (V1.60)
10
Set initial volume of handset. X ranges from 0 through 15.
set handsetout X
Set initial volume of handout. X ranges from 0 through 31.
set dualmode X
Set to enable or disable the PSTN line. X ranges from 0 through 2.
0: do not use PSTN line; 1: use PSTN line first. 1: use IP side call
first.
set dual modes prefix XX
When IP first is set in the dual modes setting, setting switches to
PSTN prefix；XX ranges from 0 through 99.
set dialplan X
Enable/disable dial plan and dial number. Parameter X ranges
from 0 through 4: 0: disable dial plan; 1: enable dial plan; 2: use
dial number; 3: use 179XX service; 4: use hotline function.
set dialnumber XX
When set dialplan value set as 2, please use this command to set
dial number. For example, with eTalk card used, please set it as
00. When set dialplan value set as 4, please use this command to
set hotline number.
set dddcode XX
Set the area code when set dialplan value set as 1or 2. For
Autres manuels pour PA168V
1
Table des matières
Autres manuels PalmMicro Porte
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
