Overland Storage SnapServerXSR 40 Manuel utilisateur

*10400557002*

SnapServer®XSR 40

Optional Sliding Rail Kit Instructions

This document describes how to upgrade the standard fixed

brackets that come pre-installed on a new SnapServer XSR 40

from Overland Storage.

WARNING: To reduce the risk of electric shock or damage to

equipment, always remove any power cords while working

with the unit.

WARNUNG: Um das Risiko eines elektrischen Schlags oder

Schäden am Gerät zu vermeiden, ziehen Sie stets den

Netzstecker, bevor Sie an der Einheit arbeiten.

AVERTISSEMENT: Pour réduire le risque de choc électrique

ou endommagement de l'équipement, retirez toujours les

cordons électriques en travaillant avec l'appareil.

CAUTION: While working with the unit, observe standard

Electrostatic Discharge (ES10400557-002D) precautions to

prevent damage to micro-circuitry or static-sensitive devices.

Prepare the Unit

NOTE: If this is a new SnapServer that has not yet been installed

into a rack, go to the “Attach the Rails” section.

Power Off and Disconnect

1. Power off the unit by pressing the Power button on the

front of the unit.

2. When all the LEDs are off, disconnect the power cord.

3. Disconnect all data cables from the unit.

Remove the Bezel

1. Carefully take hold of the front bezel by the right and left

flanges and pull straight out from the appliance until the

retaining clips release.

2. Set the bezel aside on a secure surface.

Power Socket

Data Cables

GraphicNeeded

Pull Pull

Optional Sliding Rail Kit Instructions

Remove the Drives

IMPORTANT: Overland recommends that you remove the

drive assemblies to lessen the unit’s weight prior to removal.

The assemblies must be reinstalled in the same bays when done.

NOTE: Do not remove the disk drives from their carriers. Doing so

voids the drive warranty.

This process applies to both drive assemblies and blanks:

1. Press the release button on the right side of the carrier,

and note the bay from which it is removed.

2. Using the handle, pull the assembly out.

3. Set the assembly on an ESD-safe surface.

4. Repeat Steps 1–3 for each remaining carrier.

Remove Unit from Rack

WARNING: It is recommended that a mechanical lifter (or at

least two people) be used during rack installation or removal

to prevent injury.

WARNUNG: Um Verletzungen zu vermeiden, empfehlen wir

zur Rack-Installation oder -Deinstallation die Nutzung einer

mechanischen Hebehilfe (oder mindestens zwei Personen).

AVERTISSEMENT: AVERTISSEMENT: Pour éviter toute

blessure il est recommande qu'un monte-charge (ou deux

personnes au moins) soit utilisé lors de l'installation ou de

l'enlèvement du support.

1. Remove and retain the four screws from the front

flanges and move the unit onto the lifter.

2. Move the unit onto a secure surface.

Attach the Rails

Remove Fixed Brackets

1. Remove the four screws holding the right bracket to the

chassis. Set the bracket aside.

2. On the left side, remove the four screws holding the left

bracket, and set it aside.

Press

Secure Surface

Optional Sliding Rail Kit Instructions

Attach Inner Rails to Unit

1. Select a rail assembly and slide the inner rail out until it

stops.

2. Slide the inner rail release latch forward and remove the

inner rail.

3. To retract the middle rail, release the lock (1) and slide it

back into (2) the outer rail.

4. Repeat Steps 1–3 for the other rail assembly.

5. Align the inner rail against the side of the server with

the correct side up.

6. Using the supplied screws, secure the rail.

7. Repeat Steps 5–6 for the left rail.

Optional Steps for Thicker Rack Rails

For rack rails thicker than 3mm, the sliding rail anchors

cannot be seated without exerting excessive force and

potentially damaging the sliding rail kit.The brackets need to

be removed from each end of the slide rails to make the anchors

seat securely.

For standard rack rail sizes 3mm or less, skip this procedure

and proceed to “Attach Outer Rails to Square-holed Rack.”

1. Locate the bracket on the end of a slide rail.

2. Remove the screw securing the bracket to the rail.

3. Push the bracket toward the end of the rail, prying the

back of the bracket upward to unseat and remove it.

4. Repeat Steps 1–3 for each end of both rails.

Attach Outer Rails to Square-holed Rack

NOTE: When replacing the fixed rails in a previously installed unit,

the new rails should be attached to the same front vertical rack

holes that the fixed bracket used.

1. Position the front of one of the rails in line with the front

vertical rail mounting holes (1) and move it forward until

the rail anchors are through the holes.

2. Push the rail toward the outside of the rack (2) until the

rail locks snap into place.

3. At the rear (3), slide the outer rail in or out to fit between

the vertical rails (a) and repeat Steps 1–2 to secure it (b).

NOTE: Make sure the rear holes are the same height as the

front holes so the rail is level.

4. For the other rail, repeat Steps 1–3.

Center

Screw

1 2

Rear

Optional Sliding Rail Kit Instructions

Install Lock-down Brackets on Rack

1. To install the server in the rack, first attach lock-down

brackets to the rack.

Facing the rack, place a bracket around the rail

anchors and align the center hole of the rail mounting

with the center hole of the bracket

2. Use the supplied screw in the center hole to secure the

lock-down bracket to the rack.

3. Repeat Steps 1–2 on the other side of the rack.

Install Ear Brackets on Server

1. Starting on the right side, fit the ear bracket where the

fixed bracket was removed from the chassis, then use two

screws to secure the ear bracket to the chassis.

2. Repeat Step 1 for the left ear bracket.

Install the Chassis

Install in Rack

1. Using the mechanical lifter, position the appliance in

front of the rack.

2. Insert the inner rails into the outer rails and slide the

unit into the rack.

3. Using the four retained screws, secure the SnapServer

in front of the rack.

4. For thicker racks: Using the two supplied screws,

secure the rear ends of the slide rails to the rack rails.

IMPORTANT: If this is a new appliance install, continue with

the SnapServer XSR 40 Quick Start Guide instructions for

connecting and configuring the appliance.

Lock-down Bracket

and Screw

Rail Anchors

Center Screw

Screws for

Ear Bracket

http://support.overlandstorage.com

You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using

the information found on the Contact Us page on our web site.

Optional Sliding Rail Kit Instructions

Reinstall Drives

Return the drive assemblies to the bays.

1. Position a drive assembly in front of an empty bay.

2. Slide the assembly in until the latch clicks, locking it in

the bay.

3. Repeat Steps 1–2 for all remaining drive carriers.

IMPORTANT: To maintain proper airflow and cooling, a drive

assembly or a blank carrier must be installed in every bay. No

empty bays are allowed.

Reattach the Bezel

1. Position the bezel with the top and bottom edges aligned

with the slots on the front of the appliance.

2. Push the bezel onto the unit until the retaining clips latch

and the bezel snaps into place.

3. Verify that the bezel is aligned properly and that all the

LEDs are visible.

Reattach Cables and Power Cords

1. Reattach all the cables (except the power cord) to their

previous positions.

2. Attach the power cord.

3. At the front, press the power switch to power on the

unit.

NOTE: Refer to your SnapServer XSR 40 Quick Start Guide for

complete cabling details and locations.

Slide

Retaining Clip

Power Socket

Data Cables

Autres manuels pour SnapServerXSR 40

Table des matières

Autres manuels Overland Storage Serveur

Overland Storage

Overland Storage SnapServer Manuel de service

Overland Storage

Overland Storage SnapServer N2000 Manuel utilisateur

Overland Storage

Overland Storage SnapServer XSR 120 Manuel utilisateur

Overland Storage

Overland Storage Snapshot SnapSAN Manuel utilisateur

Overland Storage

Overland Storage SnapServer Expansion E2000 Manuel utilisateur

Overland Storage

Overland Storage Snap Server 12000 Manuel utilisateur

Overland Storage

Overland Storage SnapServer XSD 40 Manuel utilisateur

Overland Storage

Overland Storage SnapSAN VSS Manuel utilisateur

Overland Storage

Overland Storage SnapServer Manuel de service

Overland Storage

Overland Storage ARCvault Series Manuel utilisateur

Overland Storage

Overland Storage SnapServer XSR 120 Manuel utilisateur

Overland Storage

Overland Storage SnapServer 510 Manuel utilisateur

Overland Storage

Overland Storage DXSeries Manuel utilisateur

Overland Storage

Overland Storage SnapScale Manuel de service

Overland Storage

Overland Storage SnapServerXSR 40 Manuel utilisateur

Overland Storage

Overland Storage SnapSAN S1000 Manuel utilisateur

Overland Storage

Overland Storage ARCvault Series Manuel utilisateur

Overland Storage

Overland Storage SnapServer DX1 Manuel utilisateur

Overland Storage

Overland Storage SnapServer DX1 Manuel utilisateur

Overland Storage

Overland Storage Snap Server 18000 Manuel utilisateur

Overland Storage

Overland Storage SnapServer 110 Manuel utilisateur

Overland Storage

Overland Storage SnapServer 2U Appliance Mode d’emploi

Overland Storage

Overland Storage Snap Server 14000 Manuel utilisateur

Overland Storage

Overland Storage snap server 410 Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur