OSS OSS-PCIe-HIB25-x4 Manuel utilisateur

PCIe x4 Gen2 Host Cable Adapter

Model: OSS-PCIe-HIB25-x4

www.onestopsystems.com

Installation Guide

SKU: OSS-PCIe-HIB25-X4

One Stop Systems

OSS-PCIe-HIB25x4 | 2

Table of Contents

Preface 4

Advisories 4

Safety Instructions 5

1 Introduction 7

1.1 Specifications 7

1.2 Overview 8

1.3 PCIe Card Edge x4 8

1.4 Power 8

1.5 PCIe Cable Sideband signals 8

1.6 Re-driver 9

1.7 Block Diagram & Signal Direction 9

1.8 Dimensions 10

1.9 HIB card Operating Mode 11

1.10 PCI Express x4 Card Edge Connector Pin Outs 12

1.11 x4 Cable Wire Connectios / Pin Outs 14

1.12 x4 Cable Signal Descriptions 15

2 Hardware Requirements 16

2.1 Hardware & System Requirements 16

2.1.1 HIB25-x4 card (Host and Target) 16

2.1.2 PCIe Slot & Motherboard Requirement 16

2.1.3 x4 iPass Cable 16

2.1.4 Gen3 Expansion Chassis / backplane 17

2.1.5 ATX Power Supply 17

2.2 Software Requirement 17

3 Installation Procedures 18

3.1 Select Host and Target Card 18

3.2 Install HIB Host card 18

3.3 Install HIB Target card 19

3.4 Install PCIe card 20

3.5 Install link cable 20

3.6 Connect ATX Power Supply 21

3.7 Power ON the system 21

4Verify Hardware 22

4.1 LED Definition 22

5 Software Installation 23

6 How to Get More Help 24

6.1 Contacting Technical Support 24

6.2 Returning Merchandise 24

One Stop Systems

OSS-PCIe-HIB25x4 | 3

6.3 Online Support Resources 24

One Stop Systems

OSS-PCIe-HIB25x4 | 4

Preface

Advisories

Five types of advisories are used throughout this manual to provide helpful information, or to alert you to the potential for hardware damage

or personal injury.

NOTE

Used to amplify or explain a comment related to procedural steps or text.

IMPORTANT

Used to indicate an important piece of information or special “tip” to help you

CAUTION

Used to indicate and prevent the following procedure or step from causing damage to the equipment.

WARNING

Used to indicate and prevent the following step from causing injury.

DANGER or STOP

Used to indicate and prevent the following step from causing serious injury or significant data loss

Disclaimer: We have attempted to identify most situations that may pose a danger, warning, or caution condition in this manual. However, the

company does not claim to have covered all situations that might require the use of a Caution, Warning, or Danger indicator.

One Stop Systems

OSS-PCIe-HIB25x4 | 5

Safety Instructions

Always use caution when servicing any electrical component. Before handling the expansion chassis, read the following instructions and safety

guidelines to prevent damage to the product and to ensure your own personal safety. Refer to the “Advisories” section for advisory

conventions used in this manual, including the distinction between Danger, Warning, Caution, Important, and Note.

Always use caution when handling/operating the computer. Only qualified, experienced, authorized electronics personnel should

access the interior of the computer and expansion chassis per UL and IEC 60950-1

The power supplies produce high voltages and energy hazards, which can cause bodily harm.

Use extreme caution when installing or removing components. Refer to the installation instructions in this manual for precautions

and procedures. If you have any questions, please contact Technical Support.

WARNING

Never modify or remove the radio frequency interference shielding from your workstation or expansion unit. To do so may

cause your installation to produce emissions that could interfere with other electronic equipment in the area of your

system.

When Working Inside a Computer

1. Before taking covers off a computer, perform the following steps:

2. Turn off the computer and any peripheral devices.

3. Disconnect the computer and peripheral power cords from their AC outlets or inlets in order to prevent electric shock or system

board damage.

In addition, take note of these safety guidelines when appropriate:

To help avoid possible damage to systems boards, wait five seconds after turning off the computer before removing a component,

removing a system board, or disconnecting a peripheral device from the computer.

When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector

with locking tabs. If you are disconnecting this type of cable, press in on the locking tabs before disconnecting the cable. As you pull

connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before connecting a cable, make sure both

connectors are correctly oriented and aligned.

CAUTION

Do not attempt to service the system yourself except as explained in this manual. Follow installation

instructions closely.

One Stop Systems

OSS-PCIe-HIB25x4 | 6

Protecting Against Electrostatic Discharge

Electrostatic Discharge (ESD) Warning

Electrostatic Discharge (ESD) is the enemy of semiconductor devices. You should always take precautions to eliminate any

electrostatic charge from your body and clothing before touching any semiconductor device or card by using an

electrostatic wrist strap and/or rubber mat.

Static electricity can harm system boards. Perform service at an ESD workstation and follow proper ESD procedures to reduce the risk of

damage to components. We strongly encourage you to follow proper ESD procedures, which can include wrist straps and smocks, when

servicing equipment.

You can also take the following steps to prevent damage from electrostatic discharge (ESD):

When unpacking a static-sensitive component from its shipping carton, do not remove the component’s anti-static packaging

material until you are ready to install the component in a computer. Just before unwrapping the anti-static packaging, be sure you

are at an ESD workstation or are grounded.

When transporting a sensitive component, first place it in an anti-static container or packaging.

Handle all sensitive components at an ESD workstation. If possible, use anti-static floor pads and workbench pads.

Handle components and boards with care. Do not touch the components or contacts on a board. Hold a board by its edges or by its

metal mounting bracket.

One Stop Systems

OSS-PCIe-HIB25x4 | 7

1 Introduction

The PCIe x4 Gen 2 cable adapter is a PCIe half-height add-in card with a PCIe x4 cable connector on the slot cover. The host cable adapter

installs in the PCIe slot of a host server and the target cable adapter installs in the Target slot / Upstream slot of the OSS backplane.

Part numbers:

OSS-PCIE-HIB25-x4-T (Target)

OSS-PCIE-HIB25-x4-H (Host)

1.1 Specifications

Item

Description

Form Factor

PCIe x4 half-height, half-length

Dimensions

2.7 x 3.1” (68 x 78mm)

Bandwidth / Backplane

Interface

PCIe x4 Gen2

Power Consumption

3.75W Typical, [email protected]

Connector

PCIe x4 Cable connector

PCIe x4 Edge connector

Re-drivers

5.0 Gbps 4-lane PCIe Gen2 Re-driver

Pericom, pat number P12EQX5804

Bracket

Standard and low profile brackets available

With two LEDs on the bracket

Operating Temperature

0˚C to +50˚C environment

Operating Humidity

10% to 90% relative humidity non-condensing

Storage Humidity

5% to 95% relative humidity non-condensing

Shock

30g Acceleration Peak (11ms pulse)

Industry Specifications

PCIe External Cabling Specification, Rev. 1.0

PCI Express™ Card Electromechanical

Specification, Rev. 2.0

PCI Express ® Base Specification, Rev. 3.0

ATX Specification, Version 2.2

Agency Compliance

• FCC Class B

• CE

• RoHS

Operating System

Windows 10, Windows Server 2012 R2; Linux OS based

One Stop Systems

OSS-PCIe-HIB25x4 | 8

1.2 Overview

*The Optocouplers are mounted on the Target card only

1.3 PCIe Card Edge x4

The PCIe Card edge will be directly routed x4 interface to the Pericom Chip

In host mode, the add-in card will accept a clock as an input.

In target mode, the add-in card will drive a clock. It will also provide a reset output and a PS_ON# signal.

1.4 Power

Power is provided by the PCI-e card slot.

Power required by internal components of OSS-PCIe-HIB-25-x4 is estimated to be 4 watts when both ports are fully linked and

operating in Gen2 mode.

Cable power is to be provided per PCIe cable specification. When an active cable (powered transceiver) is used, additional power is

required from the PCI-e card slot.

Power will be supplied +3.3V, +3.3Vaux through Card Edge.

Some power rails will be derived from the onboard circuitry.

1.5 PCIe Cable Sideband signals

All Cable sideband signals CPERST#, CPWRON, CPRSNT#, CWAKE# to be connected per the PCIe Cable specification.

Additional isolation of signal CE_PWRON# (card edge power control) shall be provided by a physical switch.

This switch allows user to electrically isolate this signal from the card edge connector.

One Stop Systems

OSS-PCIe-HIB25x4 | 9

1.6 Re-driver

The board uses the Pericom chip to link from Card Edge to Cable Connector.

The HIB card interface includes the following features

oOne x4 PCIe bus routed to PCIe Card Edge

oOne x4 PCIe bus routed to the PCIe Cable Connector

oPCIe Clock route from Card Edge to Cable Connector via a Clock Buffer.

1.7 Block Diagram & Signal Direction

One Stop Systems

OSS-PCIe-HIB25x4 | 10

1.8 Dimensions

Table des matières

Autres manuels OSS Matériel informatique

OSS

OSS OSS-PCIe4-ADPT-x8-M.2-2 Manuel utilisateur

OSS

OSS nanoCUBE OSS-PCIe-nCUBE-1-PLEX Manuel utilisateur

OSS

OSS OSS-PCIe4-BP-5X16 Manuel utilisateur

OSS

OSS OSS-KIT-EXP-3500-2M Manuel utilisateur

OSS

OSS OSS-521 Gen4 Manuel utilisateur

OSS

OSS OSS-PCIe-HIB38-x16 Manuel utilisateur

OSS

OSS 4UP 10-SLOT GEN4 Manuel utilisateur

OSS

OSS OSS-BP-419 Manuel utilisateur

OSS

OSS Centauri OSS-EXS-C4B Manuel utilisateur

OSS

OSS OSS-PCIe-HIB616-x16 Manuel utilisateur

OSS

OSS OSS-PCIe-HIB38-x8-QUAD Manuel utilisateur

OSS

OSS 4UP 16-SLOT GEN4 Manuel utilisateur

OSS

OSS OSS-PCIE-4UV-5slot Manuel utilisateur

OSS

OSS OSS-KIT-EXP-1500 Manuel utilisateur

OSS

OSS OSS-PCIe-BP-2019 Manuel utilisateur

OSS

OSS OSS-BP-427 Manuel utilisateur

OSS

OSS OSS-KIT-EXP-6002 Manuel utilisateur

OSS

OSS OSS-KIT-EXP-61611-xM Manuel utilisateur

OSS

OSS ExpressBox 2200 Manuel utilisateur

OSS

OSS ExpressBox 7 x8G2-RAS Manuel utilisateur

OSS

OSS OSS-KIT-EXP-9000-2M Manuel utilisateur

OSS

OSS OSS-581 Gen5 Backlane Manuel utilisateur

OSS

OSS EB16-Basic Manuel utilisateur

OSS

OSS OSS-KIT-EXP-3501-2M Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur