Osram Traxon ecue ARCHISHAPE 2.0 Dot S Manuel utilisateur

ARCHISHAPE®2.0 Dot S/M/L

INSTALLATION GUIDE

V1.0

Cover:

ARCHISHAPE®2.0 Dot S/M/L (ETL)

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 2 of 20

Content

1. Safety And Operation 3

2. Introduction 4

3. Installation 9

4. System Configuration 15

5. Care and Maintenance 17

6. Technical Specification 18

7. Troubleshooting 19

8. Warranty Statement 19

For your own safety and that of the product, please read this installation guide carefully before

beginning setup and installation.

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 3 of 20

1. Safety And Operation

1. CAUTION - Unplug the power supply from the mains power before connecting or disconnecting any cables

as this can damage the products.

2. CAUTION - Avoid looking directly into the LED light source at close range for your own safety.

3. Persons installing this product should make sure:

a. The installation complies with all applicable codes, state and local laws, ordinances, standards

and safety regulations.

b. The installation environment is carefully studied and suitable surge protection measure(s) is

taken.

c. He or she is qualiﬁed for the handling of electrical equipment.

4. Do not attempt to install or use the product until installation instructions and safety labels are fully understood.

This product is designed for indoor and outdoor use.

5. Ensure product operates within the speciﬁed temperature range. (Refer to 6. TECHNICAL SPECIFICATION for

more details.)

6. Do not attempt to open the product. Not user serviceable.

7. Do not use the product if any part of it, or the power cables are damaged.

8. Only use product for speciﬁed voltage, do not exceed. (Refer to 6. TECHNICAL SPECIFICATION for more

details.)

9. Always maintain connection to ensure waterprooﬁng.

10. If the product has been subjected to drastic temperature variances, for example, following transportation, do

not connect the ﬁxture until it has reached room temperature, as moisture condensation may cause electric

shock and product damages.

11. When installing the products and system power supplies, please ensure they will not be exposed to moisture

and extreme heat (and direct sunlight for outdoor products). Besides, keep a clean operating environment for

the ﬁxtures and system power supplies.

12. Please study this Installation Guide thoroughly and check the latest Technical Speciﬁcation Sheets available

from the Traxon website www.osram.us/traxon before setup.

13. Any non-compliance of the Installation Guide will void the Traxon warranty.

Please read through Safety and Operation before start of the installation.

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 4 of 20

2. Introduction

2.1 General

ARCHISHAPE®2.0 Dot is a high-brightness, fully customizable media dot solution available in S, M or L with Clear or

Diffused View lens to meet your project specifications. Each Dot is individually-addressable making ARCHISHAPE®

2.0 Dot a durable, scalable solution for vivid accents, graphics and video playback in installations of any size and

complexity.

Features:

— DMX512 Control

— Daisy Chain System

— Auto-Addressing with optional accessory & e:cue Controls

— IP66; IK09; ANSI 3G

— Suitable for irregular surfaces, planes, and conﬁgurations

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 5 of 20

2.2 Dimensions

FIG.1: ARCHISHAPE®2.0 Dot S/M/L

AS 2.0 Dot S AS 2.0 Dot M AS 2.0 Dot L

Clear View

14.4mm/0.57”

38.4mm/1.51”

AS 2.0 Dot S AS 2.0 Dot M AS 2.0 Dot L

Diffused View

10mm/0.39”

29.3mm/1.15”

14.3mm/0.56”

10mm/0.39”

29.3mm/1.15”

14.5mm/0.57”

35.5mm/1.40”

53mm/2.09”

26mm/1.02”

19mm/0.75”

12mm/0.47”

12mm/

0.47”

52.2mm/2.06”

41mm/1.61”

40mm/1.57”

φ68mm/2.68”

4 x φ3.3mm/0.13”

12mm/

0.47”

55mm/2.17”

41mm/1.61”

4 x φ3.3mm/0.13”

φ71mm/2.80”

45mm/1.77”

19mm/0.75”

53mm/2.09”

26mm/1.02”

12mm/0.47”

4 x φ3.3mm/0.13”

41mm/1.61”

40mm/1.57”

φ68mm/2.68”

12mm/

0.47”

52.2mm/2.06”

4 x φ3.3mm/0.13”

φ71mm/2.80”

41mm/1.61”

45mm/1.77”

12mm/

0.47”

55mm/2.17”

19.6mm/0.77”

25.5mm/1.00”

3.2mm/0.13” 3.2mm/0.13” 3.2mm/0.13”

19.5mm/0.77”

3.4mm/0.53”

3.2mm/0.13” 3.2mm/0.13”

3.2mm/0.13”

Mounting bracket

∅∅

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 6 of 20

FIG.2: ARCHISHAPE®2.0 Dot S/M/L Accessories

AS Dot End Cap with Resistor (

AM345880055

)

Starter Cable 16ft / 5m (

AM345860055

)

500mm (19.69")

47.2mm (1.86")

∅18mm (0.71")

12mm (0.47")

RED (1.0mm²)

GREEN (0.25mm²)

YELLOW (0.25mm²)

BLUE (0.25mm²)

BLACK (1.0mm²)

FEMALE CONNECTOR

30mm (1.18")

∅17.1mm (0.67")

∅15.6mm (0.61")

Interconnection Cable (

AM460720055

)

FEMALE CONNECTOR FEMALE CONNECTOR

∅18mm (0.71")

47.2mm (1.86") 1000mm (3.28') 47.2mm (1.86")

12mm (0.47")

18mm (0.71")

AS Dot S Mounting Clip (

AM357440055

)

19mm (0.75")

29.3mm (1.16")

10mm (0.39")

∅1.9mm (0.08”)

∅3.6mm (0.14")

Auto-addressing module (4ch AM345890055) (3ch AM456250055)

4X 5mm (0.20”)

∅

67.5mm (2.66")

61.5mm [2.42"]

∅106.5mm (4.19")

∅18mm (0.71")

48mm (1.89")

170mm (6.69")

18mm (0.709")

MALE CONNECTOR FEMALE CONNECTOR

RJ45 Power Injector Cable Kit (

AM357480055

)

42.8mm (1.69")

M17*1.0

∅19.6mm (0.77")

∅12mm (0.47")

300mm ± 20mm (11.81"± 0.79")

59.2mm (2.33")

∅18mm (0.71")

∅6.0mm (0.24")

∅7.2mm (0.28")

48mm (1.89")

150mm±10mm (5.91" ± 0.39")

22mm (0.87")

47mm (1.85")

18mm (0.71")

48mm (1.89") 39mm (1.54")

MALE CONNECTOR

TIGHTENING TORQUES: 0.7~0.9N.m

∅∅

∅

FEMALE CONNECTOR

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 7 of 20

∅∅∅∅

∅

∅"

∅

Power Injector Cable Kit (

AM460710055

)

45.5mm (1.79")

∅∅

∅

∅7.2mm (0.28")

TIGHTENING TORQUES: 0.7~0.9N.m

18mm (0.71")

∅12mm (0.47")

17.7mm (0.70") 22mm (0.87")

59.2mm (2.33")

∅18mm (0.71")

MALE CONNECTOR

FEMALE CONNECTOR

300mm ± 20mm (11.81"± 0.79")

47mm (1.85")

150mm±10mm (5.91" ± 0.39")

48mm (1.89")

FIG.3: ARCHISHAPE®2.0 Dot S/M/L String

FEMALE CONNECTORMALE CONNECTOR

150mm (5.91")

47.2mm (1.86")

∅

18mm (0.71")

∅

18mm (0.71")

500mm (19.69")

48mm (1.89")

12mm (0.47")

FEMALE CONNECTORMALE CONNECTOR

150mm (5.91")

47.2mm (1.86")

∅18mm (0.71")

∅

18mm (0.71")

500mm (19.69")

48mm (1.89")

12mm (0.47")

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 8 of 20

2.3 Packing Contents

FIG.4: ARCHISHAPE®2.0 Dot S/M/L Packing Contents

ARCHISHAPE®2.0 Dot S/M/L

FIG.5: RJ45 Power Injector Cable Kit Contents

RJ45 Power Injector Cable Kit

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 9 of 20

3. Installation

3.1 Points To Consider

Plan your installation before mounting any luminaires. The following should be considered for a successful

installation.

— Weather conditions and ambient temperature of installation site.

— Appropriate cable lengths

— Adequate space for heat dissipation (150mm / 6” apart) of LED Engines (see “3.3 On-Site Installation” on page

12).

— Appropriate anchor bolts where necessary to secure the ARCHISHAPE®2.0 Dot S/M/L.

— The number of ARCHISHAPE®2.0 Dot S/M/L and LED Engines.

— Controller to be used to control the ARCHISHAPE®2.0 Dot S/M/L.

3.2 Pre-Installation Checks

3.2.1 Installation Checklist

1. Prepare cables and all necessary accessories.

2. Perform functional check of ARCHISHAPE®2.0 Dot S/M/L.

3. Ensure the connector of last dot is covered by the End Cap Resistor.

4. Ensure all pre-installation checks laid out below have been followed.

5. Mount the ARCHISHAPE®2.0 Dot S/M/L on-site. If the installation is to be left uncompleted overnight, place

all non-connected LED Engines and ARCHISHAPE®2.0 Dot S/M/L in an indoor environment.

Ensure all the Connection Cables, ARCHISHAPE®2.0 Dot S/M/L are initially stored in a dry area to guarantee the

complete sealing of the system from water before installation.

Connector should be properly connected with cable connectors and the connector of last dot should be covered

by its Waterproof End Cap to ensure IP66 rating.

3.2.2 Handling The ARCHISHAPE®2.0 Dot S/M/L String

When transporting or preparing the ARCHISHAPE®2.0 Dot S/M/L string, please handle with care. To reduce

stress on cables, carry by the ARCHISHAPE®2.0 Dot S/M/Ls and not the cable during transit.

FIG.6: Correct way of handling ARCHISHAPE®2.0 Dot S/M/L String

Allow slack on cable to

reduce stress

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 10 of 20

3.2.3 Requirements Of Cable Bending And Twisting

Please take EXTRA precautions before bending or twisting ARCHISHAPE®2.0 Dot S/M/L cable. Lead Cable must

NOT be bent below the Minimum Bending Radius (4x Cable Diameter) and the Non-Bendable Length of 50mm /

2” near the connector end or near the cable overmold MUST be adhered to.

FIG.7: Minimum Cable Bending and Non-Bendable Length Requirement

(Non-Bendable Length)

500mm (19.69")

≥

(Minimum Bending Radius)

14mm/0.55”

20mm/0.79”

Ø7mm/0.28”

50mm/1.97”

(Minimum Bending Radius)

28mm/1.00”

≥

The ﬂat ARCHISHAPE®2.0 Dot S/M/L Cable must NOT be bent/twisted below 20mm (0.79”) from edge of

ARCHISHAPE®2.0 Dot S/M/L housing (Non-Bendable/Non-Twistable Length).

Twisting the ﬂat cable is NOT recommended. If twisting is necessary for installation, please adhere to the Non-

Twistable Length speciﬁed in Fig. 6 and ensure the mounting pitch is greater than or equal to 75% of the normal

ARCHISHAPE®2.0 Dot S/M/L to ARCHISHAPE®2.0 Dot S/M/L pitch. The middle part of the cable must be

secured to the mounting surface with a cable tie (see “3.3 On-Site Installation” on page 12 and FIG.11 on page

14). Ensure no damage is generated on the cable.

FIG.8: Minimum Clearance

20mm/0.79”

Minimum clearance

from dot

Non-Bendable/

Non-Twistable Length

NOTE: Water ingress incurred due to excess cable bending/twisting will not be warrantied by Traxon Technologies.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Osram Équipement d'éclairage

Osram

Osram 3240G4 Manuel utilisateur

Osram

Osram BY-M46 Manuel utilisateur

Osram

Osram 660 Manuel utilisateur

Osram

Osram LUMINESTRA LED 8W Manuel utilisateur

Osram

Osram DALI PCU Manuel utilisateur

Osram

Osram PL-CN35-COB-600-XXX-24D-G2 Manuel utilisateur

Osram

Osram ADB KLEMANTIS AS 1000 Manuel utilisateur

Osram

Osram BY-P28 Manuel utilisateur

Osram

Osram ARAY CTFI1100SARAY-G1-FS927-05-1L-50 Manuel utilisateur

Osram

Osram SMART+ OUTDOOR FLEX Manuel d'instructions

Osram

Osram AirZing PRO 5030 UNIV Guide de l'utilisateur

Osram

Osram PermaLED® Area Light Medium Manuel utilisateur

Osram

Osram LEDinspect POCKET 200 Manuel utilisateur

Osram

Osram Claypaky XTYLOS Manuel d'utilisation

Osram

Osram KREIOS PAR Manuel utilisateur

Osram

Osram LEDinspect Manuel utilisateur

Osram

Osram Fluence VYPR 3p Guide de dépannage

Osram

Osram Media Pixel Ribbon DMX Outdoor VB Manuel d'instructions d'installation

Osram

Osram LEDambient LEDINT203 Manuel utilisateur

Osram

Osram ZELION HL300 Grow Light Manuel utilisateur

Osram

Osram RGBWA+UVIR Slimpar Series Manuel utilisateur

Osram

Osram Traxon e:cue Allegro Media Tube Lite Manuel utilisateur

Osram

Osram Clay Paky ALPHA SPOT 300 Manuel utilisateur

Osram

Osram BY-P09 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur

Osram traxon ecue ARCHISHAPE 2.0 Dot S Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques