Q I G Quick Installation Guide
Quick Installation Guide
Version 1.1
Q I G
Cable Types and Specifications:
For pin assignments for different types of cables, please refer to the following
tables.
10/100 Base-T(X) MDI/MDI-X
Pin Number MDI port MDI-X port
1 TD+(transmit) RD+(receive)
2 TD-(transmit) RD-(receive)
3 RD+(receive) TD+(transmit)
4 Not used Not used
5 Not used Not used
6 RD-(receive) TD-(transmit)
7 Not used Not used
8 Not used Not used
Note: “+” and “-” signs represent the polarity of the wires that make up each
wire pair.
10/100 Base-T(X) RJ-45
Pin Number Assignment
1 TD+
2 TD-
3 RD+
4 Not used
5 Not used
6 RD-
7 Not used
8 Not used
Resetting
To restore the switch configurations back to the factory defaults, press the button for 5 seconds.Reset
Configurations
After installing the switch, the green power LED should turn on. Please refer to the
following tablet for LED indication.
1. Launch the Internet Explorer and type in IP address of the switch. The default static IP address is
192.168.10.2
Follow the steps to set up the card:
PRINTED ON RECYCLED PAPER
Industrial secure serial port to
Ethernet Device Server
D e v i c e
S e rv e r
Cable Type Max. Length Connector
10Base-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100Base-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000Base-T Cat. 5/Cat 5e 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000Base-T RJ-45 port
Pin Number Assignment
#1 BI_DA+
#2 BI_DA-
#3 BI_DB+
#4 BI_DC+
#5 BI_DC-
#6 BI_DB-
#7 BI_DD+
#8 BI_DD-
1000Base-T RJ-45
Pin Number MDI port MDI-X port
1 BI_DA+ BI_DB+
2 BI_DA- BI_DB-
3 BI_DB+ BI_DA+
4 BI_DC+ BI_DD+
5 BI_DC- BI_DD-
6 BI_DB- BI_DA-
7 BI_DD+ BI_DC+
8 BI_DD- BI_DC-
DB9 serial port
The device can be connected to a serial device using a DB9 cable. The DB9
connector supports RS232 / RS422 / RS485 operation modes. Please refer to the
following table for the pin assignments of the DB9 connector.
Pin # RS-232 RS-422 RS-485
( 4 wire )
RS-485
( 2 wire )
1 DCD TX- TX- DATA -
2 RXD TX+ TX+ DATA +
3 TXD RX+ RX+
4 DTR RX- RX-
5 GND GND GND
6 DSR
7 RTS
8 CTS
9 RI
1 2 3
4
5
6 7 8 9
DB9 connector
Wiring
The device has two sets of DC power inputs on a 6-pin terminal block
located on bottom of the device. Follow the steps below to wire the
power input on the terminal block.
Power inputs
STEP 1: Insert the negative/positive wires into the V-/V+ terminals, respectively.
STEP 2: To keep the wires from pulling loose, use a small flat-blade screwdriver to
tighten the wire-clamp screws on the front of the connector.
PW R-2 PWR-1
V2+ V2- Relay V1+ V1-
PWR1/2 Green On Power is on and function normally
Fault Amber On Faulty relay (power failure or port disconnected)
10/100/1000Base-T(X) Ethernet ports
LNK/ACT Green On Port is connected
Green Blinking Transmitting data
Speed
Green On Port running at 1000Mbps.
Amber On Port running at 100Mbps.
Green/ Amber Off Port running at 10Mbps.
Serial ports
S1~S4 Red On Receiving data
Green On Transmitting data
Power
Redundant Input p o wer Dua l D C inputs. 12~ 48VDC on 6 pin t e rminal bl o ck
Physical Characteristic
Encl o sure IP-30 Alu minum
Dime n sion (W x D x H) 54. 2(W)x 107. 1 (D)x 145.4 (H) mm (2.13 x4.22x5. 7 2 inch.)
Weight (g)
Environmental
-40 t o 85 C (- 4 0 to 185 F )
o o
Storage Tem p erature
5% to 9 5% Non-con d ensing
Operating Humidi ty
-40 t o 70 C (- 4 0 to 158 F )
o o
Operating Temperature
Network Protocol
740 g
Power Consumpti o n(Typ.) 6.96W
Ove rload current pro t ection Pre s ent
Reverse polari ty protection Prese n t on termina l block
Prot o col ICMP, IP, TCP, UD P, DHCP, BOOTP, SSH, DNS, SNMP, V1 /V2c, HTT PS
Regulatory Approvals
EN 55 032, CISPR 3 2, EN 61000- 3-2, EN 6100 0 -3-3, FCC Part 15 B cla ss A
EMI
EN 55 024 (IEC/E N 6 1000-4-2 ( ESD), IEC/ E N61000-4 -3 (RS), IEC / EN61000- 4-4 (EFT),
IEC / EN 61000-4 -5 (Surge) , IEC/EN 610 0 0-4-6 (CS) , IEC/EN 610 0 0-4-8(PF MF),
IEC / EN 61000-4 -11(DIP) )
EMS
IEC 6 0068-2- 2 7
Shoc k
IEC 6 0068-2- 3 1
IEC 6 0068-2- 6
Vibration
Free Fall
MTBF
560362.4721 hrs
EN6 0 950-1
Safe ty
2. Log in with default user name and password (both are admin). After logging in, you should see the
following screen. For more information on configurations, please refer to the user manual. For
information on operating the device using Oring’s Open-Vision management utility, please go to ORing
website.
RS-2 3 2
Flow C o ntrol
10/1 0 0/1000Base-T( X ) Ports in
Aut o M DI/MDIX 2
Physical Ports
Technology
Stop B i ts
Data B i ts
1, 1. 5, 2
TxD, RxD, RTS, CTS, DTR, DSR, DC D, RI, GND
XON / XOFF, RTS / CTS, DT R /DSR
7, 8
Serial Ports
Conn e ctor DB9 x 4
Operation Mode
Seri a l Baud Rate 110 bp s t o 921.6 Kbps
RS-2 3 2/422/485
IDS-342GT
Specifications
ORing Device Server
Model
Parity odd, eve n , none, mark, spac e
Jumb o f rame Up to 9. 6 K Bytes
CE EM C ( EN 55024, E N 5 5032), FCC Part 15 B
EMC
Warranty
5 ye ars
ORing Industrial Networking Corp.
Copyright© 2015 ORing
All rights reserved.
TEL: +886-2-2218-1066
FAX: +886-2-2218-1014
Website: www.oringnet.com
E-mail: support@oringnet.com
IDS-342GT
IDS-342GT
