OMP M7225 Manuel utilisateur

7225

Thank you for choosing OMP Global Style.

LARGE FIXED FLAT PANEL MOUNT

omp-global

AMERICAS

200 Norfinch Drive

To ronto, Ontario,

Canada

M3N 1Y4

Te l: 1-416-667-9909

Email: americas@omp-global.com

EUROPE/MIDDLE EAST

Common Lane

Setchey, Kings Lynn

Norfolk, PE33 0AT

England

Te l: 44-1553-813-300

Email: europe@omp-global.com

ASIA PACIFIC

1D Quadrant Dr,

Gracefield,

Lower Hutt, 5010

New Zealand

Te l: 64-4-586-6677

Email: asiapacific@omp-global.com

MOUNTING INSTALLATION INSTRUCTIONS

Designed for medium/large ﬂat panels (40”-54”) to install to a vertical wall.

Maximum load capacity: 90kgs (200lbs).

CAUTION:

If you do not understand these instructions, or have doubts about the safety of the

installation, please call a qualiﬁed installer or contact us. We will provide assistance

for any safety issues and resolve any missing component problems. Please check

carefully to make sure there are no missing or defective parts. Do not use components

with defects, as wrong installation may lead to component damage or serious injury

to the user. Do not use this product for any purpose other than the original intended

use. The hardware supplied for this product cannot be used on a steel stud wall, old

cinder block wall or a hollow wall. If you cannot determine the nature of a wall, please

consult a qualiﬁed installer. Our company will not be held responsible for damage or

loss caused by wrong installation or assembly. Regular cleaning of this product with

a clean dry cloth is usually sufﬁcient, but for stubborn marks, wipe over gently with a

clean damp cloth. Never use strong detergents or abrasives, as these may damage

the surface. There are many small components used in the construction of this unit,

these loose items should be kept away from young children whilst assembling your

unit. Do not exceed the maximum weight capacity for this product. Your installer is

responsible for ensuring the safe installation of this product.

COMPONENTS

1x wall plate (A)

4x M6x35 screws (E) 4x M8x35 screws (F)

1x monitor bracket (B) 4x M4x35 screws (C) 4x M5x35 screws (D)

4x spacer (G) 4x square pad (H)

CAUTION:

Our company accepts responsibility for the safety of the mount and the television link,

but does not accept responsibility for the link between the mount and the wall.

NECESSARY TOOLS:

6mm (1/4”) drill bit, 13mm (1/2”) masonry drill bit, (for concrete installation),

17mm (11/16”) ratchet wrench, level, stud ﬁnder and a Philips head screwdriver.

The components and the attachments of this product are shown in ﬁg. 1.

g. 1

4x O10 metal pad (I) 4x square head screw bolt (J) 4x wall anchor (K)

MOUNTING WALL PLATE

Four installation choices are covered: wood stud, brick, solid concrete and

concrete block.

Wood stud installation:

The wall plate (A) must be anchored to the two wood studs at a distance over

30.5cm (12”). Use a high quality wood stud ﬁnder, to locate two adjacent studs. We

suggest using and awl, or thin nails, to conﬁrm the location of the wood stud (as

shown in ﬁg. 2.1). Use the 7mm (5/16”) drill bit and drill 88mm (3 1/2”) deep holes in

each of wood stud’s. Then use four 9mm (3/8”) square head screw bolts (J) and four

metal pads (I) and install the wall plate to the wall, please make sure the installation

direction of the wall plate is correct (as shown in ﬁg. 2.2).

Brick, solid concrete and concrete block installation:

Use wall plate (A) as a template and mark four holes in the wall. The left and right hole

places should be spread as far apart as possible. Use the 13mm (1/2”) drill bits

to drill these holes making sure the depth is at least 88mm (3 1/2”). Put two bolts

in the top row of slots and two in the bottom row. Make sure these holes are level,

and that there is at least 15.2cm (6”) between any two holes. Insert wall anchor (K)

into these holes, making sure they are ﬂush with the wall surface. Finally use the four

square head screw bolts (J) to install the wall plate to the wall (as shown in ﬁg. 2.3).

STEP 1

WARNING

When installing the wall mount onto a solid concrete wall, verify that you have a

minimum of 35mm (1 3/8”) of actual concrete thickness in the hole to be used for the

concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of

the wall. It is suggested that a standard electric drill on a slow setting is used to drill

the hole, instead of a hammer drill.

The concrete must be 2000PSI minimum density.

The anchors must be seated ﬁrmly against the concrete or masonry. If mounting to a

masonry wall covered with drywall/plaster, counter bore a hole through the drywall/

plaster around the mounting hole location, so that the anchor can be seated directly

against concrete or masonry.

g. 2.1 g. 2.2 g. 2.3

concrete wall plate concrete

wall plate

concrete

CORRECT INCORRECT

concrete

plaster/drywall plaster/drywall

SELECT THE CORRECT MOUNTING HARDWARE FOR YOUR

TELEVISION

CAUTION: Always make sure the television is unplugged, before threading any bolt

into the back panel! First ﬁnd the screw holes in the television’s back, then select the

screws that ﬁt the screw holes dimension.

IMPORTANT: If you cannot ﬁnd the hardware that ﬁts your television, please contact

your local hardware shop.

INSTALLATION OF THE MONITOR BRACKETS TO THE BACK

OF THE TELEVISION

CAUTION: Never lay the television face down on the glass, it should be tilted or

leaned against a wall or other solid surface. Laying the television face down on the

glass, may lead to permanent damage.

Before installation, the monitor brackets (B) must be vertically placed and the distance

from the television to the bracket should be as short as possible. For a television that

has the slot in the back, thread the screws (C,D,E or F) through the square pad (H),

the monitor bracket (B) and spacers (G) into the television. Finally tighten the screws

ﬁrmly with a Philips screwdriver (as shown in ﬁg. 3).

INSTALL THE MOUNT ASSEMBLY AND TELEVISION TO THE

WALL PLATE

CAUTION: Some televisions are heavy, please lift and place carefully. We will not be

held responsible for any accidental damage.

Attach the monitor brackets (B)’s hook to the wall plate (A)’s cross bar, then tighten

screws (L, supplied attached to monitor bracket B) to secure the monitor brackets with

the wall plate, to prevent the pivot arm assembly falling off the wall plate, (as shown

in ﬁg. 4).

STEP 2

STEP 3

STEP 4

g. 4

g. 3

C,D,E or F

Autres manuels OMP Support TV

OMP

OMP M7441 Manuel utilisateur

Manuels Support TV populaires d'autres marques

Ergotron

Ergotron Neo Flex Cantilever UHD Manuel utilisateur

StarTech.com

StarTech.com FPCEILBTB Manuel utilisateur

VonHaus

VonHaus 05/038 Manuel utilisateur

Techlink

Techlink ECHO TV Manuel utilisateur

Sandstrom

Sandstrom SSTVMC12X Manuel utilisateur

Sony

Sony SU-WL700 Mode d’emploi

ICW

ICW SCACC18 Manuel utilisateur

LG WM-L640V Manuel utilisateur

Gembird

Gembird WM-65ST-01 Manuel utilisateur

ERARD

ERARD FiTUP XXL 035320 Manuel utilisateur

PEERLESS

PEERLESS PLCK-1 Mode d’emploi

Kanto

Kanto RCF180 Manuel utilisateur

GEM

GEM GEM GP001 Manuel utilisateur

Gladiator Joe

Gladiator Joe GJ0A0053 Manuel utilisateur

Vivotek

Vivotek AM-105 Manuel utilisateur

Vivo

Vivo VESA STAND-VAD1B Manuel utilisateur

AmazonBasics

AmazonBasics B07QG3LMG4 Manuel utilisateur

Secura

Secura QLF210 Manuel utilisateur