OLIMEX PIC-P28 Manuel utilisateur
PIC-P28 development board
Users Manual
All boards produced by Olimex are ROHS compliant
Rev. D, February 2008
Copyright(c) 2008, OLIMEX Ltd, All rights reserved
Page 1
INTRODUCTION:
PIC-P28 board is development board which allow you to prototype and
develop code for all Microchip’s PIC microcontrollers with 28 pins.
What you can do with PIC-P28? A lot of stuff let’s see what we have:
PIC-P28 have RS232 connector and driver, so you can interface your
PIC microcontroller to other embedded or PC with RS232. The RS232
driver have 4 lines Tx, Rx, CTS and jumper selectable RTS or DTR.
The pin labeled RX is output and should be connected to PIC UART Tx.
The pin labeled TX is input and should be connected to PIC UART Rx.
Note that MAX232 driver on the socket is 5V device, so if you decide
to run your PIC on 3.3V you should replace it with MAX3232 which
works on 3.3V
The on-board ICSP connector allow you to program the PIC on the
board without pulling it of the socket, by ICSP programmer like PIC-
MCP, PIC-MCP-USB, PIC-PG1, PIC-PG2, PIC-PG3, PIC-PG4 or to
program and debug it with PIC-ICD2, PIC-ICD2-POCKET or PIC-ICD2-
TINY. IMPORTANT: all programmers provide power supply through
ICSP connector during the programming PIC-P18 should not be
powered via the external power jack!
The power supply circuit have diode bridge after the power supply jack
which allow you to power this board with both AC and DC power
supply adapters. The input voltage could be anything within the range
+7.5 – 15V DC or 6-12V AC.
Voltage regulator is made with LM317 adjustable voltage regulator and
have jumper which selects what voltage you supply to the PIC
microcontroller +3.3V or +5V, so you can work with PICs on both low
and normal voltage.
The oscillator circuit is made with 20 Mhz crystal oscillator, so you
can run your PIC at maximum performance.
The RESET circuit is made with simple RC circuit and RESET push
button, the reason to not use RESET IC is that the board should
support both 3.3V and 5V operation while RESET ICs are on fixed
voltage.
PIC-P28 have user button for user input connected to PIC
microcontroller’s RA5 port. When RA5 port is initialized as INPUT you
will read “0” when the button is pressed and “1” when it is depressed.
Status LED is connected via jumper to PIC microcontroller’s RA0 port.
When your RA0 port is initialized as OUTPUT and set to “0” LED will
go ON, when RA0 port is set to “1” LED will go OFF.
PIC-P28 have handy GND pin for connection to oscilloscope.
Page 2
Page 3
FEATURES:
•ICSP/ICD connector for programming and debugging
•RS232 interface with MAX232 IC on socket
•DIL28 microcontroller socket
•Quartz crystal 20Mhz
•LED to RA0 through jumper
•user Button to RA5
•Reset button and circuit
•Power plug-in jack, accept AC and DC input
•selectable +3.3V / +5V power supply voltage regulator (3.3V when jumper is
closed)
•Extension slot on every uC pin
•Gird 100 mils
•GND bus
•Vcc bus
•Four mounting holes 3,3 mm (0,13")
•FR-4, 1.5 mm (0,062"), green soldermask, white silkscreen component print
•Dimensions 100x80 mm (3,9x3,15")
Page 4
SCHEMATIC:
Page 5
4.7uF/25VDC
4.7uF/25VDC 4.7uF/25VDC
4.7uF/25VDC
4.7uF/25VDC
470uF/16VDC 100uF/16VDC
100n
22p
22p
100n
NA 1N4004
B-DIL
+5V
+5V
+5V
+5V
4-20MHz
330
10K
390/1%
240/1%
330/1%
10k
PIC28pin
MAX232
LM317
3.3V
BUT
C1
C2 C3
C4
C5
C6 C7
C8
C9
C10
C11
C12
CTS
D1
G1
1
2
3
4
5
6
ICSP
1
2
3
J1
LED
LED_J
PWR
Q1
R1
R2
R3
R4
R5
R6
1
2
3
4
5
6
7
8
9
RS232
RST
RTS/DTR
RX
TX
INT/RB0 21
MCLR#/THV
1
OSC1/CLKIN
9
OSC2/CLKOUT
10
PGC/RB6 27
PGD/RB7 28
PGM/RB3 24
RA0/AN0
2
RA1/AN1
3
RA2/AN2
4
RA3/AN3
5
RA4/T0CKI
6
RA5/AN4
7RB1 22
RB2 23
RB4 25
RB5 26
RC0/T1OSO
11
RC1/T1OSI
12
RC2/CCP1
13
RC3/SCL/SCK
14
RX/RC7 18
SDI/SDA/RC4 15
SDO/RC5 16
TX/RC6 17
20 8
19
U1
VDD
VSS
C1+ 1
C1- 3
C2+ 4
C2- 5
R1IN
13 R1OUT 12
R2IN
8R2OUT 9
T1IN 11
T1OUT
14
T2IN 10
T2OUT
7
V+
2
V-
6
U2
1516
GNDVCC
U2P
ADJ
IN OUT
VR
12-RTS
23-DTR
6VAC
9VDC
PIC-P28
Rev. D
COPYRIGHT(C) 2008, Olimex Ltd.
http://www.olimex.com/dev
SOFTWARE:
DEMO1: PIC16F876-I/P BLINK LED
This is demo code which blinks the LED on PIC-P28 board.
Note:
LED jumper should be closed!
DEMO2: PIC16F876-I/P
BUTTON read
This is demo code which show how to read BUTTON status and to switch
the LED ON when button is pressed and LED off when the button is
depressed.
DEMO3: PIC16F876-I/P
RS232 send / receive routines
This is demo code, which show how to use the USART to send and receive
characters from host PC via RS232 cable.
The MAX232 by default is not connected to PIC on the board so you have to
solder two wires – one from RC6 (pin #17) of PIC16F876 Tx signal to
MAX232 Rx labeled pin, and second from RC7 (pin #18) of PIC16F876 Rx
signal to MAX232 Tx labeled pin.
You must program the HEX code to PIC16F876 and run the code.
If you programmed the PIC correctly and wired the UART, when you open
Hyperterminal on your host PC computer with 9600 bps, 8 data bit, 1 stop
bit, No flow control and apply power supply to the PIC-P28 every character
you type on the hyperterminal will be printed back with “*” i.e. if you type
“abc” you will receive “a*b*c*”.
Page 6
ORDER CODE:
PIC-P28 – assembled and tested (no kit, no soldering required)
PIC-P28/PCB – blank PCBs only
How to order?
You can order to us directly or by any of our distributors.
Check our web www.olimex.com/dev for more info.
Revision history:
REV. D - create February 2008
Page 7
Disclaimer:
© 2008 Olimex Ltd. All rights reserved. Olimex®, logo and combinations thereof, are registered trademarks of
Olimex Ltd. Other terms and product names may be trademarks of others.
The information in this document is provided in connection with Olimex products. No license, express or implied
or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Olimex
products.
Neither the whole nor any part of the information contained in or the product described in this document may be
adapted or reproduced in any material from except with the prior written permission of the copyright holder.
The product described in this document is subject to continuous development and improvements. All particulars of
the product and its use contained in this document are given by OLIMEX in good faith. However all warranties
implied or expressed including but not limited to implied warranties of merchantability or fitness for purpose are
excluded.
This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for
any loss or damage arising from the use of any information in this document or any error or omission in such
information or any incorrect use of the product.
Page 8
Table des matières
Autres manuels OLIMEX Carte mère
OLIMEX
OLIMEX IMX233-OLX-NANO Manuel utilisateur
OLIMEX
OLIMEX OLinuXino-MAXI Manuel utilisateur
OLIMEX
OLIMEX STM32-E407 Manuel utilisateur
OLIMEX
OLIMEX LPC-E2468 Manuel utilisateur
OLIMEX
OLIMEX LPC-P11C24 Manuel utilisateur
OLIMEX
OLIMEX STM32-P107 Manuel utilisateur
OLIMEX
OLIMEX MSP430-5510STK Manuel utilisateur
OLIMEX
OLIMEX STM32-P407 Manuel utilisateur
OLIMEX
OLIMEX STM32-P152 Manuel utilisateur
OLIMEX
OLIMEX ESP8266 Series Guide de démarrage rapide
OLIMEX
OLIMEX OLinuXino-MAXI Manuel utilisateur
OLIMEX
OLIMEX OLIMEXINO-328 Manuel utilisateur
OLIMEX
OLIMEX MOD-VGA Manuel utilisateur
OLIMEX
OLIMEX ESP8266-EVB Mode d'emploi
OLIMEX
OLIMEX A13-OLinuXino-MICRO Manuel utilisateur
OLIMEX
OLIMEX MOD-VGA Manuel utilisateur
OLIMEX
OLIMEX AVR-ISP500-ISO Manuel utilisateur
OLIMEX
OLIMEX SAM9-L9261 Manuel utilisateur
OLIMEX
OLIMEX MOD-WiFi Manuel utilisateur
OLIMEX
OLIMEX LPC11C24 Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
