Okin Refined MC242 Feuille d'instructions
Issue department
：
Bedding Division
Date
：
2021-10-11
Product Function
instruction
Author
：
BenYang
No：MC242
MC242
Version：1.1
Page 2 of 5
2. Function Picture
1. Process of test
1.1. HEAD MOTOR
Connect to head actuator,control by remote single:
Click head up button on the remote, head actuator moves out, stop when released；
Click head down button，head actuator moves in, stop when released；
This function takes effect only by pressing the corresponding button on the remote.
1.2. FOOT MOTOR
Connect to foot actuator,control by remote single:
Click foot up button，foot actuator moves out，stop when released；
Click foot down button，foot actuator moves in，stop when released；
This function takes effect only by pressing the corresponding button on the remote.
2
Issue department
：
Bedding Division
Date
：
2021-10-11
Product Function
instruction
Author
：
BenYang
No：MC242
MC242
Version：1.1
Page 3 of 5
1.3. T I LT and Lumbar MOTOR
Connect to TILT and Lumbar actuator,control by remote single:
Click bed up button，TILT and Lumbar actuator moves out，stop when released；
Click bed down button，TILT and Lumbar actuator moves in，stop when released；
This function takes effect only by pressing the corresponding button on the remote.
1.4. Massage
Connect to Foot and Head vibrator,control by remote single:
Click ALL Massage button, Foot and Head vibrator work,and click again,the strength enhance,there is 3
degree all.
1.5. SYNC port
Connect with the same other Control box or Other accessories;
1.6. Power LED & PAIRING LED
Power supply for control box, PAIRING LED of control box is blue, POWER LED is green。
1.7. Power
Connect to the 29V DC;
1.8. RESET button
Press and hold the RESET button，the Head, Foot actuators will moves to lower position.
1.9. Pair Function
Once power on ，pairing LED turns on，the control box enters into mode of code paring；
Press and hold the paring LED of Remote, the backlight of paring LED flashes, the backlight of remote flashes, the
remote enters into mode of code paring;
3
Issue department
：
Bedding Division
Date
：
2021-10-11
Product Function
instruction
Author
：
BenYang
No：MC242
MC242
Version：1.1
Page 4 of 5
The backlight of paring LED of remote stops flashing, and the paring led of control box turns off, it indicates that
the code paring is successful;
If fails, repeat all the processes above;
1.10. FLAT function
Press and release the FLAT button on remote，the head and foot actuators moves to lower position(when the
actuator is free, can turn off the vibration motor and turn off the indicator light when press once )，stop when
press any buton；
This function takes effect only by pressing the corresponding button on the remote.
1.11. ZERO G position function
Press and release ZERO G button on remote，the head and foot actuator moves to preset memory position，stop
when press any button；
This function takes effect only by pressing the corresponding button on the remote.
4
FCC：
Any C hanges or m odifications not e xpressly a pproved b y the pa rty r esponsible f or c ompliance
could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC R ules. Operation is subject to t he f ollowing two
conditions: (1) This device may n ot cause harmful interference, and ( 2) this device must accept
any interference received, including interference that may cause undesired operation.
5
ISED RSS Warning:
This device complies with Innovation,Science and Economic Development Canada licenceexempt
RSS standard(s). Operation is subject to the following t wo c onditions: (1) this device may not
cause i nterference, and (2) this de vice must accept any interference, i ncluding interference t hat
may cause undesired operation of the device.
Le pr ésent appa reil es t con forme aux C NR d' ISED a pplicables aux appareils r adioexempts de
licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même s i
le brouillage est susceptible d'en compromettre le fonctionnement.
ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment.The device has been evaluated to meet general RF exposure requirement.
Le matériel est conforme aux limites de dose d'exposition aux rayonnements énoncés
pour fac un autre environnement.ce dispositif a été évalué à satisfaire l'exigence
générale de l'exposition aux rf.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Table des matières
Autres manuels Okin Refined Unité de contrôle
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
