Oki C9600hdn Manuel utilisateur

Finisher Unit Installation Guide

Components

1. Finisher unit

2. Finisher stand

3. Inverter unit

4. Stacking tray

5. Rear cover

6. Clear band

7. Band stopper (2)

Prepare the Printer

1. Turn the printer off and disconnect the power

cord and interface cable.

2. Using a screwdriver, remove the breakout

panels on the side of the printer.

3. Open the face-up stacker.

4. Open the flap and press it onto the stacker

surface

4

2

3

1

5

7

6

2

5. Close the stacker.

6. Install the metal brackets as shown.

Assemble the Finisher

1. Attach the guide rail of the inverter to the

printer with 2 screws.

2. Hook the finisher stand to the inverter.

3. Attach the finisher stand to the inverter with 2

screws.

4. Slip one end of the clear band over the tab on

the right side of the rear cover at a right

angle.

3

5. Slip the other end of the band through the

retainer on the finisher, then secure it with the

smaller stopper.

6. Turn the cover so it faces the finisher.

7. Place the larger stopper over the tab and turn

to lock it in position

8. Attach the rear cover to the finisher and close

it.

9. Loosen the screw on the locking piece so that

it drops through the slot below. This keeps the

platform from moving while you attach the

finisher to it.

10.Position the finisher on the stand and attach

it with two screws from the back.

11.Swivel the locking piece up and tighten the

screw firmly. Be sure it’s out of the way and

the screw is tight—otherwise the platform will

not move freely.

© 2005 Oki Data Americas, Inc. 58372801

12.Position the stacker on the back of the

finisher with the hooks engaged.

13.Make sure the lever on the finisher is

positioned above the stacker.

14.Attach the stacker with four screws.

Complete the Assembly

1. Push the finisher against the printer until the

prongs on the printer brackets fit into the

holes in the finisher.

2. If you need to, turn the levellers on the

finisher to raise or lower the finisher so the

holes and prongs align properly. Make sure the

finisher is level.

3. Connect the printer and the finisher to the

inverter, and connect the inverter’s power

cord.

Leveller

Autres manuels pour C9600hdn

18

Ce manuel convient aux modèles suivants

2

Autres manuels Oki Accessoires pour imprimantes

Manuels Accessoires pour imprimantes populaires d'autres marques

Star Micronics

Star Micronics TSP800 Series Manuel utilisateur

REA

REA JET HR pro 2K Manuel utilisateur

HP

HP Laserjet,Color Laserjet 4si Manuel utilisateur

oliser

oliser MS 45 Manuel utilisateur

Roland

Roland DU2-64 Instructions et recettes

Xerox

Xerox EFI EXP6000 Manuel utilisateur

Canon

Canon Finisher-T1 Manuel utilisateur

Sharp

Sharp FO-1MK Manuel utilisateur

Labelmate

Labelmate PM-300 Manuel utilisateur

Epson

Epson T6248 Manuel d'utilisation

Epson

Epson OT-BZ20 Manuel utilisateur

Canon

Canon TonerRobot EP-27 Manuel utilisateur

Ricoh

Ricoh LCIT RT5100 Guide de démarrage rapide

GBC

GBC 16 Series Manuel utilisateur

Canon

Canon INNER 2-WAY TRAY-E1 Manuel d'utilisation et d'entretien

Develop

Develop SD-509 Manuel utilisateur

Kyocera

Kyocera KM-6230 Manuel

Triumph Adler

Triumph Adler DF-710 Manuel