OHAUS SD Manuel utilisateur

Quick Start Guide SD Scales

Ohaus Corporation www.ohaus.com iSD Shipping Scales Quick Start Guide

PREPARATION FOR USE

Battery Installation:

Open battery cover on bottom of

the Indicator. Install three LR14

(“C”) batteries (not included).

Orient batteries as shown on

inside cover. Close battery cover.

AC Adapter Installation:

Check that local line voltage

matches voltage printed on the AC

adapter label. Then connect the

scale to the power supply.

Mount Indicator as desired.

…with or without brackets.

Options below:

120mm / 4.72˝

90mm / 3.54˝

SELECTING THE LOCATION:

Place on a firm, steady surface.

Avoid excessive air current, vibrations, heat

sources, or rapid temperature changes.

Use leveling feet to level the base.

SAFETY PRECAUTIONS

•Before plugging in the indicator, verify that local power supply matches voltage printed

on AC adapter. (Use only the adapter provided.)

•Disconnect the indicator from the power supply when cleaning.

•Do not operate this product in hazardous or unstable environments.

•Do not drop loads on the platform.

•Operate the product only under ambient conditions specified in the Instruction Manual.

•Service should be performed by authorized personnel only.

SD Scales Quick Start Guide

SD Shipping Scales Quick Start Guide ii Ohaus Corporation www.ohaus.com

CONTROLS

Button Functions

UNITS

Cal

Short Press

Long Press

Changes weighing unit and weighing mode.

In Dynamic Weighing Mode, starts countdown.

Starts calibration.

ON/ZERO

Off

Short Press (when off)

Short Press:(when on)

Long Press

Turns scale on.

If balance is on, sets display to zero.

Turns scale off.

OPERATION

Power Up Test: Press ON/ZERO Off.All display segments appear, then the software version.

Display resets to zero.

Zero Function: Press ON/ZERO Off when scale is on, display returns to zero.

When adding additional mass, press ON/ZERO Off repeatedly to scale’s full capacity.

With a container, press ON/ZERO Off to Tare. Add mass to see NET weight. If both sample

and container are removed, a negative value will be displayed. Press ON/ZERO Off to Zero.

Overload: If load exceeds scale capacity, “E” appears. Remove load, scale returns to normal.

Auto Shut-Off: When running on batteries, scale turns off after four inactive minutes.

Dynamic Weighing

With platform empty, press UNITS Cal until bullet • flashes.

Place a mass on the platform. The scale shows “-A-”.

(If using a container, press ON/ZERO Off to tare and return to zero.

Short-press UNITS Cal to start the averaging countdown from 5 seconds.

Averaged weight appears. Bullet • stops flashing when process is complete.

Display holds until a button is pressed.

To repeat process, press UNITS Cal with a mass on platform or container.

To Exit, remove mass from platform or container. Press UNITS Cal.

*80253132*

P/N 80253132

Stability

symbol

Battery charge

symbol

Symbols for weighing

modes:

lb – Pounds

•

– Dynamic Weighing

kg – Kilograms

Negative

symbol

Table des matières

Autres manuels OHAUS Échelle

OHAUS

OHAUS Aviator 7000 Manuel utilisateur

OHAUS

OHAUS Valor 7000 series Manuel utilisateur

OHAUS

OHAUS ES series Manuel utilisateur

OHAUS

OHAUS PR Series Manuel utilisateur

OHAUS

OHAUS Ranger 7000 R71MHD3 Manuel utilisateur

OHAUS

OHAUS RC41M15-M Manuel utilisateur

OHAUS

OHAUS Valor 1000 Manuel utilisateur

OHAUS

OHAUS Guardian 3000 Manuel utilisateur

OHAUS

OHAUS Scout SJX Series Manuel utilisateur

OHAUS

OHAUS Valor 1000 Manuel utilisateur

OHAUS

OHAUS ES series Manuel utilisateur

OHAUS

OHAUS CS 2000 Manuel utilisateur

OHAUS

OHAUS Navigator Series Manuel utilisateur

OHAUS

OHAUS SCOUT II Manuel utilisateur

OHAUS

OHAUS Adventurer series Manuel utilisateur

OHAUS

OHAUS Adventurer Pro Grain Manuel utilisateur

OHAUS

OHAUS EX124 Manuel utilisateur

OHAUS

OHAUS EXPLORER PRO Manuel utilisateur

OHAUS

OHAUS Valor 1000 Manuel utilisateur

OHAUS

OHAUS skx series Manuel utilisateur

OHAUS

OHAUS 1119D Manuel utilisateur

OHAUS

OHAUS AP110 Manuel utilisateur

OHAUS

OHAUS CHAMP II BASE Manuel utilisateur

OHAUS

OHAUS Compact Series Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur