Nvent Eriflex Flexibar UDF500 Manuel utilisateur

5 mm

Position 15.5 mm

ERIFLEX FLEXIBAR

as shown

86.0

16.1 13.3

NOTE:

1. Tighten screws of all unused galleries to the specified torque above.

2. For multiple phase assemblies, join blocks together before installing on DIN profile.

3. The input must be fixed or maintained at approximately 15cm from the block.

I: 500A

Ui: 1000V AC/DC

Uimp: 12kV

Ipk: 51kA

Icw: 23kA rms 1s

IEC 60947-7-1

(IEC 60947-7-1 Ratings)

INSTRUCTION SHEET

UDF500

569060 N

WARNING:

nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at

www.nVent.com

and from your nVent customer service representative.

nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.

All instructions must be

completely

followed to ensure proper and safe installation and performance.

Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property

damage, serious bodily injury and/or death, and void your warranty.

SAFETY INSTRUCTIONS:

All governing codes and regulations and those required by the job site must be observed.

Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.

nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by

nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change

specifications without prior notice.

1 OF 2

IP7805_S

TECHNICAL SUPPORT

www.nVent.com

3/16"

Position 15.5 mm

ERIFLEX FLEXIBAR

as shown

#10

3.39

.63 .52

NOTE:

1. Tighten screws of all unused galleries to the specified torque above.

2. For multiple phase assemblies, join blocks together before installing on DIN profile.

335A

600V AC/DC

UL 1059

(UL1059 Ratings)

INSTRUCTION SHEET

UDF500

569060 N

WARNING:

nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at

www.nVent.com

and from your nVent customer service representative.

nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.

All instructions must be

completely

followed to ensure proper and safe installation and performance.

Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property

damage, serious bodily injury and/or death, and void your warranty.

SAFETY INSTRUCTIONS:

All governing codes and regulations and those required by the job site must be observed.

Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.

nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by

nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change

specifications without prior notice.

2 OF 2

IP7805_S

TECHNICAL SUPPORT

www.nVent.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels nvent Unité de contrôle

nvent

nvent ERICO Plus Manuel utilisateur

nvent

nvent Raychem RMM2 Manuel utilisateur

nvent

nvent Raychem HWAT ECO V5 Manuel utilisateur

nvent

nvent HWAT ECO Manuel utilisateur

nvent

nvent ERIFLEX UDJ125A Manuel utilisateur

nvent

nvent Raychem NGC-40-BRIDGE Manuel utilisateur

nvent

nvent HWAT-ECO-GF Manuel utilisateur

nvent

nvent Raychem NGC-CMA Manuel utilisateur

nvent

nvent Raychem HWAT-ECO V4 Manuel utilisateur

nvent

nvent RAYCHEM HWAT-ECO-GF Manuel utilisateur

nvent

nvent RAYCHEM NGC-40-IO Manuel utilisateur

nvent

nvent Raychem TraceTek TTA-SIM Instructions d'installation

nvent

nvent Eriflex Flexibar UDF250 Manuel utilisateur

nvent

nvent RAYCHEM NGC-40-PTM Manuel utilisateur

nvent

nvent Raychem Raystat-M2 Manuel utilisateur

nvent

nvent Raychem NGC-30-CR Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur

nvent Eriflex Flexibar UDF500 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques