Nuvoton ISD15D00 Manuel de programmation

FAQ

2012.11 Ver.00

ISD15D00/3800 trouble shooting manual

1 Description

This document describe troubleshooting steps and methods of ISD15D00 and ISD3800. User

can check problems with check list or reference the check steps of chapter3: VPE + Dongle +

Demo board.

2 Check list:

Environment1: VPE + Dongle + Demo board

①Check clock(3.2)：Check CLK CFG by VPE & check J9 Jumper* if use EXT_RES or XTAL

②Check CFG(3.1)

③Already burn device(3.4)?

Environment2: VPE + Dongle + User’s board with ISD15D00/3800

①Check clock(3.2)：Check CLK CFG by VPE & check crystal or resistor for EXT_RES

②Check CFG(3.1)

③Already burn device(3.4)?

Environment3: User’s MCU + Demo board

①Check SPI commands sequence(5.1) and reset signal

②Check SPI waveform by scope(3.6). Also check if SSB pull high after command.

③Already burn device(3.4)?

④Check clock(5.4)：Check CLK CFG & check J9 Jumper* if use EXT_RES or XTAL

⑤Check CFG(5.5)

⑥Check status byte(5.6)

General check: for any ISD3800 application environment

⑦Check if Flash is empty. Check system VMs: POI VM, PU VM and Wakeup VM. Check

Schematic.

⑧Understand timing

⑨Know how to unlock a device which is locked by bad flash content.

⑩Know how to solve the programming difficulty under certain configurations.

※J9’s printing “Ext_Res”and “XTAL”are reversed. Be careful Jumper’s position.

FAQ

2012.11 Ver.00

3 VPE + Dongle + Demo board:

Hardware：①Dongle：ISD-ES-MINI-USB

②Demo Board：ISD-DEMO3800 or ISD-DEMO15D00

③Speaker

Software：ISD-VPE15D00

Example project：C:\ProgramFiles\ISD-VPE15D00\ISD15D00example_1\ISD15D00example_1.prj

FAQ

2012.11 Ver.00

3.1 Check CFG : Check by VPE, click “Read CFG” at page “Configuration Registers”.

By example1：CFG02：0x48

CFG05：0x80

CFG18：0xAB

If need to modify CFG, type in value and click “Write CFG”.

※For detailed configuration register, reference Section 12.3 of design guide.

FAQ

2012.11 Ver.00

3.2 Check Clock: Check by VPE, click “Read CLK CFG” at page “Audio Cmds”.

By example1：CLK CFG：0x34

Table 12-1 of Design Guide：Clock Configuration Register Description

Table 12-2：Clock Configuration source

※For detailed clock configuration, reference Section 12.1 of design guide.

FAQ

2012.11 Ver.00

3.3 Play Voice Prompt：choose a sound and click “Play to device”.

“Play to device”will transfer sound data through SPI to Demo board and play it immediately. It does

not play VP in Flash.

FAQ

2012.11 Ver.00

3.4 Burn Device: will download .mem file into flash. Before executing SPI commands, be sure

already “Burn Device”.

Before “Burn Device”, execute “Create Programming File”and will generate .mem file. (Example1：

C:\Program Files\ISD-VPE15D00\ISD15D00example_1\ISD15D00example_1.mem)

FAQ

2012.11 Ver.00

3.5 Execute by SPI commands:

①choose a VP and click “Play VP”.

②choose a VM and click “Execute VM”

Just send SPI commands but without sound data. Play VP and VM in Flash, programmed by “Burn

Device”before.

FAQ

2012.11 Ver.00

③“Send SPI Cmd”：With proper ①configuration and ②burn device and ③PU(Power Up), send

SPI command Play VP(0xA6) should be played.

By example1, to play VP of index C：A6000C

Section 13.1.1 of design guide：Play Voice Prompt

※For detailed SPI commands, reference Chapter 13 of design guide.

FAQ

2012.11 Ver.00

3.6 Check SPI waveform:

Measure waveforms of SCLK, SSB, MISO, MOSI.

FAQ

2012.11 Ver.00

Waveform1 of whole 0xA6000C by 50us：

Check if SSB pull high after each command.

Waveform2 of detailed 0xA6000C by 10us：

MISO response：0x60 0x60 0x60

Ce manuel convient aux modèles suivants

Autres manuels Nuvoton Carte mère

Nuvoton

Nuvoton NuMicro NuMaker-IoT-MA35D1-A1 Manuel utilisateur

Nuvoton

Nuvoton NuMicro series Manuel utilisateur

Nuvoton

Nuvoton NuMaker-HMI-M467 Manuel utilisateur

Nuvoton

Nuvoton NAU8224 Manuel utilisateur

Nuvoton

Nuvoton NuMaker Series Manuel utilisateur

Nuvoton

Nuvoton NuMaker RTU NUC980 Manuel utilisateur

Nuvoton

Nuvoton NuMicro NuMaker-M091YD Manuel utilisateur

Nuvoton

Nuvoton NuMaker-M029GGC Manuel utilisateur

Nuvoton

Nuvoton NuMicro NUC200 Series Manuel utilisateur

Nuvoton

Nuvoton NuMaker Tomato Manuel utilisateur

Nuvoton

Nuvoton NuMaker-HMI-N9H26 Manuel utilisateur

Nuvoton

Nuvoton ISD93 Series Manuel utilisateur

Nuvoton

Nuvoton Nu-Link2-Pro Manuel utilisateur

Nuvoton

Nuvoton NuMicro 8051 Series Manuel utilisateur

Nuvoton

Nuvoton NuMaker NUC1262SE Manuel utilisateur

Nuvoton

Nuvoton NAU8220 Manuel utilisateur

Nuvoton

Nuvoton NuDesign HMI-N9H26 Manuel utilisateur

Nuvoton

Nuvoton NuMicro series Manuel utilisateur

Nuvoton

Nuvoton NuMicro M252 Series Manuel utilisateur

Nuvoton

Nuvoton NPCM750x EVB Manuel utilisateur

Nuvoton

Nuvoton NuMaker-M2354 Manuel utilisateur

Nuvoton

Nuvoton NuMaker NUC980 IIoT Manuel utilisateur

Nuvoton

Nuvoton NuMicro NuMaker-M463KG Manuel utilisateur

Nuvoton

Nuvoton NuMicro series Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur