Nordson Encore HD Guide de référence
EncorerHD Pump Module
Customer Product Manual
Part 1613941-01
Issued 03/19
NORDSON CORPORATION •AMHERST, OHIO •USA
For parts and technical support, call the Industrial Coating
Systems Customer Support Center at (800) 433-9319 or
contact your local Nordson representative.
This document is subject to change without notice.
Check http://emanuals.nordson.com for the latest version.
Part 1613941−01 E2019 Nordson Corporation
Contact Us
Nordson Corporation welcomes requests for information, comments, and
inquiries about its products. General information about Nordson can be
found on the Internet using the following address:
http://www.nordson.com.
Address all correspondence to:
Nordson Corporation
Attn: Customer Service
555 Jackson Street
Amherst, OH 44001
Notice
This is a Nordson Corporation publication which is protected by copyright.
Original copyright date 2019. No part of this document may be
photocopied, reproduced, or translated to another language without the
prior written consent of Nordson Corporation. The information contained
in this publication is subject to change without notice.
Trademarks
Encore, Nordson and the Nordson logo are registered trademarks of
Nordson Corporation.
All other trademarks are the property of their respective owners.
Change Record i
Part 1613941-01
E2019 Nordson Corporation
Change Record
Revision Date Change
01 03/19 New release
Change Record
ii
Part 1613941-01 E2019 Nordson Corporation
Table of Contents iii
Part 1613941−01
E2019 Nordson Corporation
Table of Contents
Safety 1.................................................
Qualified Personnel 1...................................
Intended Use 1.........................................
Regulations and Approvals 1.............................
Personal Safety 2.......................................
Fire Safety 2...........................................
Grounding 3...........................................
Action in the Event of a Malfunction 3.....................
Disposal 3.............................................
Description 4............................................
Introduction 4..........................................
Specifications 5.........................................
Installation 7............................................
Standard Pump Module Mount 7..........................
Connections 8..........................................
Installing and Removing the Muffler 8......................
System Ground 8.......................................
Manifold Solenoid Valve Functions 9......................
Manifold Wiring Diagram 10...............................
Maintenance and Repair 11.................................
Troubleshooting 12.......................................
Parts 13..................................................
Using the Illustrated Parts List 13..........................
Pump Module Assembly 14................................
Pump Module Unit 15....................................
Pump Module Manifold 16.................................
EncorerHD Pump Module 1
Part 1613941−01
E2019 Nordson Corporation
EncorerHD Pump Module
Safety
Read and follow these safety instructions. Task-specific and
equipment-specific warnings, cautions, and instructions are included in
equipment documentation where appropriate.
Make sure all equipment documentation, including these instructions, is
accessible to all persons operating or servicing equipment.
Qualified Personnel
Equipment owners are responsible for making sure that Nordson equipment
is installed, operated, and serviced by qualified personnel. Qualified
personnel are those employees or contractors who are trained to safely
perform their assigned tasks. They are familiar with all relevant safety rules
and regulations and are physically capable of performing their assigned
tasks.
Intended Use
Use of Nordson equipment in ways other than those described in the
documentation supplied with the equipment may result in injury to persons
or damage to property.
Some examples of unintended use of equipment include
Susing incompatible materials
Smaking unauthorized modifications
Sremoving or bypassing safety guards or interlocks
Susing incompatible or damaged parts
Susing unapproved auxiliary equipment
Soperating equipment in excess of maximum ratings
Regulations and Approvals
Make sure all equipment is rated and approved for the environment in which
it is used. Any approvals obtained for Nordson equipment will be voided if
instructions for installation, operation, and service are not followed.
All phases of equipment installation must comply with all federal, state, and
local codes.
EncorerHD Pump Module
2
Part 1613941−01 E2019 Nordson Corporation
Personal Safety
To prevent injury, follow these instructions.
SDo not operate or service equipment unless you are qualified.
SDo not operate equipment unless safety guards, doors, or covers are
intact and automatic interlocks are operating properly. Do not bypass or
disarm any safety devices.
SKeep clear of moving equipment. Before adjusting or servicing any
moving equipment, shut off the power supply and wait until the
equipment comes to a complete stop. Lock out power and secure the
equipment to prevent unexpected movement.
SRelieve (bleed off) hydraulic and pneumatic pressure before adjusting or
servicing pressurized systems or components. Disconnect, lock out,
and tag switches before servicing electrical equipment.
SObtain and read Safety Data Sheets (SDS) for all materials used.
Follow the manufacturer’s instructions for safe handling and use of
materials, and use recommended personal protection devices.
STo prevent injury, be aware of less-obvious dangers in the workplace
that often cannot be completely eliminated, such as hot surfaces, sharp
edges, energized electrical circuits, and moving parts that cannot be
enclosed or otherwise guarded for practical reasons.
Fire Safety
To avoid a fire or explosion, follow these instructions.
SDo not smoke, weld, grind, or use open flames where flammable
materials are being used or stored.
SProvide adequate ventilation to prevent dangerous concentrations of
volatile materials or vapors. Refer to local codes or your material SDS
for guidance.
SDo not disconnect live electrical circuits while working with flammable
materials. Shut off power at a disconnect switch first to prevent
sparking.
SKnow where emergency stop buttons, shutoff valves, and fire
extinguishers are located. If a fire starts in a spray booth, immediately
shut off the spray system and exhaust fans.
SClean, maintain, test, and repair equipment according to the instructions
in your equipment documentation.
SUse only replacement parts that are designed for use with original
equipment. Contact your Nordson representative for parts information
and advice.
EncorerHD Pump Module 3
Part 1613941−01
E2019 Nordson Corporation
Grounding
WARNING: Operating faulty electrostatic equipment is hazardous and can
cause electrocution, fire, or explosion. Make resistance checks part of your
periodic maintenance program. If you receive even a slight electrical shock
or notice static sparking or arcing, shut down all electrical or electrostatic
equipment immediately. Do not restart the equipment until the problem has
been identified and corrected.
Grounding inside and around the booth openings must comply with NFPA
requirements for Class II Division 1 or 2 Hazardous Locations. Refer to
NFPA 33, NFPA 70 (NEC articles 500, 502, and 516), and NFPA 77, latest
conditions.
SAll electrically conductive objects in the spray areas shall be electrically
connected to ground with a resistance of not more than 1 megohm as
measured with an instrument that applies at least 500 volts to the circuit
being evaluated.
SEquipment to be grounded includes, but is not limited to, the floor of the
spray area, operator platforms, hoppers, photoeye supports, and
blow-off nozzles. Personnel working in the spray area must be
grounded.
SThere is a possible ignition potential from the charged human body.
Personnel standing on a painted surface, such as an operator platform,
or wearing non-conductive shoes, are not grounded. Personnel must
wear shoes with conductive soles or use a ground strap to maintain a
connection to ground when working with or around electrostatic
equipment.
SOperators must maintain skin-to-handle contact between their hand and
the gun handle to prevent shocks while operating manual electrostatic
spray guns. If gloves must be worn, cut away the palm or fingers, wear
electrically conductive gloves, or wear a grounding strap connected to
the gun handle or other true earth ground.
SShut off electrostatic power supplies and ground gun electrodes before
making adjustments or cleaning powder spray guns.
SConnect all disconnected equipment, ground cables, and wires after
servicing equipment.
Action in the Event of a Malfunction
If a system or any equipment in a system malfunctions, shut off the system
immediately and perform the following steps:
SDisconnect and lock out electrical power. Close pneumatic shutoff
valves and relieve pressures.
SIdentify the reason for the malfunction and correct it before restarting the
equipment. If the malfunction cannot be identified, unplug the unit and
replace with spare unit if available.
Disposal
Dispose of equipment and materials used in operation and servicing
according to local codes.
EncorerHD Pump Module
4
Part 1613941−01 E2019 Nordson Corporation
Description
Introduction
See Figure 1. This manual covers the EncoreRHD pump module, which
can be used with Encore HD manual powder spray systems and automatic
powder spray systems.
The pump module comes equipped with an Encore HD, HD+ or an XD
powder feed pump. The unit contains the pneumatic circuit, which controls
the pump.
Encore HD Encore HD+
(Encore XD Not Shown)
Figure 1 Encore HD Pump Modules
Autres manuels pour Encore HD
8
Table des matières
Autres manuels Nordson Unité de contrôle
Nordson
Nordson Auto-Flo II Guide de référence
Nordson
Nordson Tribomatic II Guide de référence
Nordson
Nordson iTRAX PRx Guide de référence
Nordson
Nordson Rhino SD2CE Manuel utilisateur
Nordson
Nordson Auto-Flo II Guide de référence
Nordson
Nordson Encore HD Guide de référence
Nordson
Nordson Tribomatic II Manuel utilisateur
Nordson
Nordson Vantage Guide de référence
Nordson
Nordson Auto-Flo II Manuel utilisateur
Nordson
Nordson 768670A Manuel utilisateur
Nordson
Nordson Liquidyn P-Jet CT Manuel utilisateur
Nordson
Nordson Rhino SD2 CE Manuel utilisateur
Nordson
Nordson iTrax Manuel utilisateur
Nordson
Nordson Auto-Flo RT Gun Guide de référence
Nordson
Nordson iTRAX PRx II Guide de référence
Nordson
Nordson 754V-SS Manuel utilisateur
Nordson
Nordson A7A Manuel utilisateur
Nordson
Nordson Auto-Flo II Manuel utilisateur
Nordson
Nordson Liquidyn P-Dot CT Manuel utilisateur
Nordson
Nordson Rhino SD3 Guide de référence
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
