Nokia LPS-6 Manuel utilisateur

User Guide

Nokia Wireless Loopset LPS-6

Issue 1 EN

Contents

Safety 3

Get started 4

Keys and parts 4

Charge the battery 4

Take the loopset into use 5

Pair and connect your loopset with your

phone 6

Pair and connect your loopset using NFC 6

Basic use 8

Make and receive calls 8

Handle two calls 8

Listen wirelessly with Bluetooth 8

Use USB audio connection 9

Change the volume 9

Clear settings or reset your loopset 10

Troubleshooting 11

Product and safety information 12

Copyrights and other notices 16

Copyrights and other notices 19

User Guide

Nokia Wireless Loopset LPS-6

Safety

Read these simple guidelines. Not following them may be dangerous or illegal.

We invite you to read the instructions on this guide before using the device.

SWITCH OFF IN RESTRICTED AREAS

Switch the device off when mobile phone use is not allowed or when it may cause interference

or danger, for example, in aircraft, in hospitals or near medical equipment, fuel, chemicals, or

blasting areas. Obey all instructions in restricted areas.

ROAD SAFETY COMES FIRST

Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first

consideration while driving should be road safety.

INTERFERENCE

All wireless devices may be susceptible to interference, which could affect performance.

QUALIFIED SERVICE

Only qualified personnel may install or repair this product.

BATTERIES, CHARGERS, AND OTHER ACCESSORIES

Use only batteries, chargers, and other accessories approved by Nokia for use with this device.

Do not connect incompatible products.

KEEP YOUR DEVICE DRY

Your device is not water-resistant. Keep it dry.

PROTECT YOUR HEARING

To prevent possible hearing damage, do not listen at high volume levels for long periods. Exercise

caution when holding your device near your ear while the loudspeaker is in use.

Get started

Keys and parts

1 Neck loop

2 Vibrating alert motor

3Multifunctionkey

4Microphone

5NFCarea

6 USB connector

7 Charging status indicator

8Volumekeys

9Powerkey

10 Bluetooth connection indicator

Charge the battery

1. Connect the charger to a wall outlet.

2. Connect the charger cable to the charger connector.

The charging status indicator shows the progress of the charging, turning from red to yellow and

finally to green when the battery is fully charged. Charging the battery fully may take up to 2 hours.

3. When the battery is fully charged, disconnect the charger from the loopset first, then from the wall

outlet.

The fully charged battery has power for up to 12 hours of talk time or up to 300 hours of standby

time.

Tip: To check the charging status when you're connected to a phone, press the power key. The

charging status indicator shows the battery level (red=low, yellow=good, green=full).

When the battery is close to discharged, the loopset vibrates and beeps about every 5 minutes, and

the charging status indicator quickly flashes red.

Take the loopset into use

1. If necessary, pull out the neck loop plug.

2. Place the neck loop around your neck, and push the plug in the connector.

3. To switch on, press the power key.

If you haven't paired the loopset with any device before, the loopset vibrates once, and the Blueooth

connection indicator blinks quickly.

4. To enter pairing mode, press the multifunction key for about 2 seconds.

The Bluetooth connection indicator flashes steadily. You can now pair the loopset with a phone.

If you have paired the loopset before, the loopset tries to connect to the device that you last paired

with. The loopset remembers the last 8 devices that it was paired with. If it doesn't detect the latest

one, it tries to connect to the next, and so on.

Switch the loopset off

To switch off, press and hold the power key.

The loopset vibrates twice and the Bluetooth connection indicator stops blinking or flashing.

Pair and connect your loopset with your phone

Make sure your loopset is switched on, and in pairing mode.

1. Activate Bluetooth on your phone, and search for Bluetooth devices.

2. Select the loopset from the list to pair your phone with it.

3. If necessary, enter the passcode 0000.

Your loopset is now paired and connected with your phone. The Bluetooth connection indicator slowly

flashes.

When you switch on the loopset the next time, it automatically tries to recreate the latest connection.

Tip: When your loopset is connected to a device, but you need to pair with other devices, you

can go back to pairing mode by pressing the multifunction key for about 5 seconds.

If the loopset is not connected to a paired device within about 30 minutes, it switches off

automatically.

If the connection is lost, the loopset vibrates and the Bluetooth connection indicator quickly blinks.

Pair and connect your loopset using NFC

If your phone supports Near Field Communication (NFC), you can quickly pair and connect your

loopset, or switch the connection between paired devices.

1. On your phone, make sure that NFC is on and the phone keys and screen are unlocked.

2. Make sure the loopset is on and in pairing mode.

3. Tap the NFC area of the loopset with the NFC area of the phone.

4. If asked, accept the connection on your phone.

Disconnect or reconnect a paired device

To disconnect a paired and connected device from your loopset, tap the NFC areas together. To

reconnect, tap the NFC areas together again.

Basic use

Make and receive calls

Make sure that you're wearing the loopset properly, the loopset is connected to your phone, and your

hearing aid is in T-mode or MT-mode.

1. To make a call, use the phone keys to dial the number.

2. To answer or end a call, press the multifunction key, or use the phone keys.

3. To reject an incoming call, press the multifunction key twice.

4. To re-dial the number you last called, press the multifunction key twice.

Tip:If your loopset is switched off when there's an incoming call on the phoneyou last connected

the loopset with, just switch on the loopset, and it answers the call.

Handle two calls

Make sure that your phone supports Bluetooth hands-free profile 1.6, and that call waiting is available

on your phone. Call waiting is a network service.

1. To answer a waiting call and end the active call, press the multifunction key.

2. To answer a waiting call and put the active call on hold, press and hold the multifunction key for

about 2 seconds.

3. To end the active call and make the call on hold active, press the multifunction key.

4. To switch between the active call and the call on hold, press and hold the multifunction key for

about 2 seconds.

Listen wirelessly with Bluetooth

You can, for example, listen to music on your computer using a Bluetooth connection.

1. Connect the loopset to your phone or Bluetooth audio source, for example, your computer.

2. To play music, use the playback controls on the connected device.

Use USB audio connection

You can connect your loopset to a compatible device with a USB cable. This way you can make internet

calls or listen to music, for example, on your computer.

1. Connect a compatible USB cable to another device.

2. Use the controls on the device to handle the sound.

Tip: When you're connected, for example, to a computer with a USB cable, the battery is being

charged.

Change the volume

Press the volume keys up or down during a call or when listening to an audio source.

During a call, you don't need to adjust the volume on both your loopset and your phone, as the volume

controls are synchronised. Use the volume keys on one or the other. When you listen to a source

other than your phone using Bluetooth (A2DP mode), both controls affect the volume.

Change the sidetone volume

Sidetone is the sound that the loopset microphone routes to your hearing aid during a call to help

you hear your own voice.

During a call, press the multifunction key twice, and press a volume key within 15 seconds.

Clear settings or reset your loopset

1. To clear pairing and volume settings, press and hold the multifunction key for more than 8 seconds.

2. To reset, connect the loopset to a charger, and press and hold the multifunction key.

Resetting doesn't clear the settings.

Table des matières

Autres manuels Nokia casque

Nokia

Nokia BH-900 Manuel utilisateur

Nokia

Nokia BH-118 Manuel utilisateur

Nokia

Nokia BH-608 Manuel utilisateur

Nokia

Nokia BH-108 Manuel utilisateur

Nokia

Nokia BH-310 Manuel utilisateur

Nokia

Nokia BH-606 Manuel utilisateur

Nokia

Nokia BH-214 Manuel de service

Nokia

Nokia BH 212 - Headset - Over-the-ear Manuel utilisateur

Nokia

Nokia BH-200 Manuel utilisateur

Nokia

Nokia BH-111 Manuel utilisateur

Nokia

Nokia BH-112 Manuel utilisateur

Nokia

Nokia HS 26W - Headset - Over-the-ear Manuel utilisateur

Nokia

Nokia WH 600 - Headset - Binaural Manuel utilisateur

Nokia

Nokia HS-69 - Headset - Ear-bud Guide de démarrage rapide

Nokia

Nokia HS 36W Manuel utilisateur

Nokia

Nokia BH-215 Manuel utilisateur

Nokia

Nokia HDW 3 - Headset - Over-the-ear Manuel utilisateur

Nokia

Nokia N-GAGE Manuel utilisateur

Nokia

Nokia HS-55W Manuel utilisateur

Nokia

Nokia BH-200 Manuel utilisateur

Nokia

Nokia Luna Manuel utilisateur

Nokia

Nokia BH-101 Manuel utilisateur

Nokia

Nokia BH-207 Manuel utilisateur

Nokia

Nokia BH-606 Manuel utilisateur

Manuels casque populaires d'autres marques

Sena

Sena SMH10 Manuel utilisateur

IASUS

IASUS Stealth IA-NT4-BASIC-BT Manuel utilisateur

Sennheiser

Sennheiser EPOS ADAPT 230 Manuel utilisateur

Doro

Doro Flexus HS2005 Manuel utilisateur

GE 98971 Manuel utilisateur

Hama

Hama 00184070 Manuel utilisateur

Plantronics

Plantronics Blackwire 3200 Series Manuel utilisateur

Blue Tiger

Blue Tiger Advantage PLUS Manuel utilisateur

Jawbone

Jawbone Icon Manuel utilisateur

Jabra

Jabra FR 20 Manuel utilisateur

Roxcore

Roxcore Flow A+ Manuel utilisateur

Turtle Beach

Turtle Beach XP 510 Manuel utilisateur

Philips

Philips SHB6101 Manuel utilisateur

Jabra

Jabra PRO 9460 Duo Manuel utilisateur

HyperX

HyperX HyperX Cloud Flight Manuel utilisateur

Bose

Bose MIE2 Mobile Manuel utilisateur

Jabra

Jabra Steel Manuel utilisateur

HyperX

HyperX cloud ii Manuel utilisateur