NETGEAR ProSafe GS105v3 Manuel utilisateur

)NSTALLATION'UIDE

ProSafe 5-Port Gigabit Ethernet Switch GS105v3

Estimated installation time: 5-10 minutes

Package Contents

The package includes:

• ProSafe 5-Port Gigabit Ethernet Switch GS105v3

• AC power adapter

•GS105v3 Installation Guide (this document)

• Warranty/Support information card

Prepare to Install the Switch

Decide where you want to place the switch. Find a flat horizontal surface such as a table,

desk or shelf. You can use wall-mounting screws (not provided) to hang the switch in an

open space on a wall.

Make sure the selected location is:

• Not in direct sunlight or near a heater or heating vent.

• Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on

all sides of the switch.

• Well ventilated (especially if it is in a closet).

Depending on the speed of your network devices, you need a Category 3 (10 Mbps),

Category 5 (100 Mbps) or Category 5e (1000 Mbps) Ethernet cable with RJ-45 connectors

for each device you want to connect to the switch. Each Ethernet cable must be less than

328 feet (100 meters).

Install the Switch and Connect the Other Devices

1. Place the switch on a flat surface or hook onto the screws.

2. For each device, insert one end of an Ethernet cable into the port in the device and

insert the other end into one of the Ethernet ports on the switch.

3. Connect the power adapter cord into the back of the switch and then plug the adapter

into a power source (such as a wall socket or power strip).

4. Check the LEDs to verify that the equipment is connected correctly.

• The Power LED is lit.

• Each RJ-45 jack has 2 LEDs. For each jack that is connected to a powered

device, the Link LED is lit, and it flashes when activity occurs. If the connection

is 10 Mbps or 100 Mbps, one LED lights up. If the connection is 1000 Mbps,

both LEDs light up.

Note: If any light does not operate as indicated, go to the Troubleshooting section.

GS105v3 5-Port

Gigabit Ethernet Switch

modem

firewall

Power

100 Mbps

10 Mbps LED

Both LEDs light for

a 1000 Mbps connection.

Troubleshooting

The Power light is not lit.

The switch has no power.

• Make sure that the power cord is correctly connected to the switch.

• Make sure that the power adapter is connected to a functioning power outlet. If it is in

a power strip, make sure that the power strip is turned on. If the socket is controlled

by a light switch, make sure that the switch is in the on position.

• Make sure you that are using the NETGEAR power adapter supplied with your

switch.

The Port number light is not lit for a connected device or stays on continuously.

There is a hardware connection problem.

• Make sure that the cable connectors are securely plugged in at the switch and the

device.

• Make sure that the connected device is turned on.

• If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure that

the card or adapter is installed correctly and is working.

• Make sure that the cable is less than 328 feet (100 meters).

June, 2008

This symbol was placed in accordance with the European Union Directive

2002/96 on the Waste Electrical and Electronic Equipment (the WEEE

Directive). If disposed of within the European Union, this product should be

treated and recycled in accordance with the laws of your jurisdiction

implementing the WEEE Directive.

trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product

names are trademarks or registered trademarks of their respective holders. Information is subject to

change without notice.

Technical Specifications

Standards compatibility ISO/IEG 802.3i (ANSI/IEEE 802.i) 10BASE-T, IEEE 802.3i

10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3z

1000BASE-T, IEEE 802.3x Flow Control; Jumbo frame 9K,

IEEE 802.1p priority; DSCP priority. Compatible with

Windows, Mac OS, NetWare, Linux.

Network interface RJ-45 connector for 10BASE-T, 100BASE-T, or 1000BASE-T

Ethernet interface

Power 12W max and 12V@1A DC input

Power consumption 3W max

Physical dimensions W: 104 mm (4.1") D: 94 mm (3.7") H: 27 mm (1.1")

Weight 0.28 kg (0.621 lbs)

Operating temperature 0 to 50¡ C (32 to 122¡ F)

Operating humidity 10% to 90% relative humidity, noncondensing

Electromagnetic

compliance FCC Part 15, Class A; EN 55 022 (CISPR 22), VCCI Class A

Safety agency approvals

for the power adapter CE mark, C-Tick

Performance Specifications

Frame filter rate 14,800 frames/sec max for 10M port / 148,000 frames/sec

max for 100M port/1,480,000 frames/sec for 1000M port

Frame forward rate 14,800 frames/sec max for 10M port / 148,000 frames/sec

max for 100M port / 1,480,000 frames/sec max for 1000M

port

Network latency (using

1500-byte packets) 10Mbs: 1250us max

100Mbs: 125us max

1000Mbs: 15us max

Address database size 4000 MAC addresses

Queue buffer 128 KB Embedded

Technical Support

Thank you for selecting NETGEAR products.

After completing the Smart Wizard configuration assistant, locate the serial number on the

bottom label of your product, and use it to register your product at

http://www.NETGEAR.com/register.

Registration on the website or over the phone is required before you can use our telephone

support service. The phone numbers for worldwide regional customer support centers are

on the Warranty and Support Information card that came with your product.

Go to http://kbserver.netgear.com for product updates and Web support.

Statement of Conditions

In the interest of improving internal design, operational function, and/operability, NETGEAR reserves the

right to make changes to the product described in this document without notice. NETGEAR does not

assume any liability that may occur due to the use or application of the product(s) or circuit layout(s)

described herein.

Autres manuels NETGEAR Changer

NETGEAR

NETGEAR GS516T - ProSafe Switch Manuel utilisateur

NETGEAR

NETGEAR ProSafe GSM7324 Manuel utilisateur

NETGEAR

NETGEAR ProSAFE M4300 series Manuel utilisateur

NETGEAR

NETGEAR M4100 Series ProSAFE Manuel utilisateur

NETGEAR

NETGEAR DS 508 Manuel utilisateur

NETGEAR

NETGEAR GS108T - ProSafe - Gigabit Smart Switch Manuel utilisateur

NETGEAR

NETGEAR ProSAFE GS105PE Manuel utilisateur

NETGEAR

NETGEAR FS726TP - ProSafe Smart Switch Instructions de montage

NETGEAR

NETGEAR FS116 Manuel utilisateur

NETGEAR

NETGEAR ProSafe JGS524 V2 Manuel utilisateur

NETGEAR

NETGEAR GSM7248 - ProSafe Switch Manuel utilisateur

NETGEAR

NETGEAR FS700TS Manuel

NETGEAR

NETGEAR FSM7328S - ProSafe Switch Manuel utilisateur

NETGEAR

NETGEAR ProSafe GSM7228PS Manuel utilisateur

NETGEAR

NETGEAR 200 Series Manuel utilisateur

NETGEAR

NETGEAR EN516 - Hub - EN Manuel utilisateur

NETGEAR

NETGEAR ProSafe GS700TP Mode d’emploi

NETGEAR

NETGEAR GS110EMX Manuel utilisateur

NETGEAR

NETGEAR FS108P - ProSafe Switch Manuel utilisateur

NETGEAR

NETGEAR XS728T ProSAFE Manuel utilisateur

NETGEAR

NETGEAR GS724TS - ProSafe 24 Port Gigabit Stackable Smart... Manuel utilisateur

NETGEAR

NETGEAR WFS709TP - ProSafe Smart Wireless Controller Manuel utilisateur

NETGEAR

NETGEAR GSM7328S - ProSafe Switch - Stackable Manuel utilisateur

NETGEAR

NETGEAR GS724AT - ProSafe Gigabit Smart Switch Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur