NETGEAR M6100 Series Manuel utilisateur

Installation Guide

M6100 - Campus Edge and SMB Core

Chassis Switch

Switch blades: XCM8944, XCM8948, XCM8944F, and XCM8924X

Daughter cards: XCM89P and XCM89UP

Contents

M6100 switch blade front panels .........................................................3

Before installing the switch blades.......................................................4

Install the chassis ....................................................................................5

Install a switch blade ..............................................................................7

Install a power supply.............................................................................9

Install an optional PoE or UPoE card ..................................................11

Congure the switch ............................................................................12

Congure the IP address of the switch ..............................................13

M6100 switch blade front panels

Console

ports USB port

10G SFP+ ports 10G RJ-45 ports

XCM8924X

XCM8944

1G RJ-45 ports 10G SFP+ ports 10G RJ-45 ports

1G SFP ports 10G SFP+ ports 10G RJ-45 ports

1G RJ-45 ports

XCM8944F

XCM8948

OoB port

USB port

OoB port

Console

ports

Console

ports

Console

ports

USB port

OoB port

USB port

OoB port

Before installing the switch blades

The M6100 series switch blades are designed to be installed in the

XCM8903 switch chassis. We recommend installing the XCM8903 chassis

into a rack before installing any switch blades. For more information about

how to install the XCM8903 switch chassis, see the M6100 - Campus Edge

and SMB Core Chassis Switch, Blades, and Daughter Cards Hardware

Installation Guide.

Install the chassis

You can either rack-mount the chassis into a rack or install the chassis

using the included rails. For information about installing the chassis using

rails, see the Campus Edge and SMB Core Chassis Switches M6100 Series

Hardware Installation Guide.

To rack-mount the chassis:

1. Partially screw two of the included screws into the rack where you

want the bottom of the chassis to rest.

2. Rest the bottom of the chassis’s brackets on the two screws.

3. Attach the rest of the screws to secure the bracket to the rack.

Console

XCM8948

Supervisor

PWR/

Status

Reset

PoE(Max60Wperport): Off = no PD Green = PoE powered Yellow = PoE fault RJ45SPD/Link/Act Mode: Green = link at 1G Yellow = Link at 10/100M Blink = ACT

OOB

USB

4. Install the fan tray

To install the fan tray:

1. Carefully slide the fan tray all the way into the fan tray bay at the rear

of the chassis.

The fan tray is connected to power when it has been inserted

completely into the fan tray bay.

2. Screw the fan tray to the rear of the chassis using the included screws.

Install a switch blade

To install a switch blade in a M6100 series chassis switch:

1. Select a slot for the switch blade.

2. Remove a blank front panel from the chassis slot, if necessary.

Any unoccupied switch blade slot in the chassis must have a blank

faceplate installed to ensure satisfactory protection from EMI and to

maintain adequate airﬂow through the chassis.

3. Remove the switch blade from the antistatic packaging.

CAUTION: To prevent ESD damage, hold the switch blade by the

metal rail and front panel only. Never touch the components on the

PCB or the pins on any of the connectors.

4. Verify that the switch blade injector-ejector handles are open.

5. Keep the injector-ejector handles in the open position as you slide the

switch blade into the chassis slot.

CAUTION: Do not slide the switch blade into the open chassis slot if

the injector-ejector handles are in the latched position.

6. Using both hands, push both handles toward the center of the switch

blade, as shown.

7. Use your ngers or a screwdriver to turn the front panel screws on

each injector-ejector handle clockwise and completely down.

When the screw is fully tightened, the yellow band around the captive

screw is completely hidden.

CAUTION: Be careful to avoid over-torquing and stripping the

screws.

Console

XCM8948

Supervisor

PWR/

Status

Reset

PoE(Max60W per port): Off = no PD Green = PoE powered Yellow= PoE fault RJ45SPD/Link/ActMode: Green = link at 1G Yellow = Link at 10/100M Blink = ACT

OOB

USB

Install a power supply

To install a power supply:

1. Carefully slide the power supply all the way into the power supply bay

until it clicks into place.

CAUTION: Do not force the power supply into the system backplane.

2. Use the locking handle to secure the power supply in the power

supply bay.

3. Repeat Step 1 and Step 2 to install each additional power supply.

Locking handle

4. After you install all power supplies, connect an AC power cord to the

AC input connector below each power supply.

WARNING: Be sure that the source outlet is properly grounded

before plugging the AC power cord into the input connector.

Autres manuels pour M6100 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels NETGEAR Changer

NETGEAR

NETGEAR GS510TLP Manuel utilisateur

NETGEAR

NETGEAR FSM726v3 - ProSafe Fast Ethernet L2 Managed... Manuel utilisateur

NETGEAR

NETGEAR FSM7328S - ProSafe Switch Mode d’emploi

NETGEAR

NETGEAR ProSAFE GS105PE Manuel utilisateur

NETGEAR

NETGEAR GSM7328S - ProSafe Switch - Stackable Manuel utilisateur

NETGEAR

NETGEAR M5300 Series Manuel utilisateur

NETGEAR

NETGEAR M4100 Series ProSAFE Manuel

NETGEAR

NETGEAR GS728TS Smart Switch Manuel

NETGEAR

NETGEAR DS104 Manuel utilisateur

NETGEAR

NETGEAR FS608 Manuel utilisateur

NETGEAR

NETGEAR FS309T Manuel utilisateur

NETGEAR

NETGEAR ProSAFE GS105v5 Manuel utilisateur

NETGEAR

NETGEAR FS116 Manuel utilisateur

NETGEAR

NETGEAR XS708T Manuel utilisateur

NETGEAR

NETGEAR GS316 Manuel utilisateur

NETGEAR

NETGEAR ProSafe GS700TS Manuel

NETGEAR

NETGEAR FS108P - ProSafe Switch Manuel utilisateur

NETGEAR

NETGEAR FVS338 - ProSafe VPN Firewall 50 Router Manuel utilisateur

NETGEAR

NETGEAR GSM7224 - Switch Manuel

NETGEAR

NETGEAR ProSafe FS750T2 Manuel utilisateur

NETGEAR

NETGEAR GS700AT Series Mode d’emploi

NETGEAR

NETGEAR ProSAFE FS526Tv2 Manuel utilisateur

NETGEAR

NETGEAR GC752XP Manuel

NETGEAR

NETGEAR GS748T - ProSafe Smart Switch Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur