NetComm Wireless NP124 Manuel utilisateur

What to do if you cannot open the configuration page

(NP124)

What to do if you cannot open the configuration page of the NP124

If the NP124 has been previously configured, the DHCP would be disabled and you would not be able to open

the configuration page http://192.168.20.1 automatically. This guide will take you through the steps to allow

you to open the configuration page when that happens. There are two ways of allowing you access to the

configuration page: Reset the NP124 or Set a static IP address on your computer. Ensure that your computer

is connected to the Ethernet port of the NP124 before you proceed with the guide.

Resetting the NP124

1. Ensure that the NP124 is powered on.

2. There is a reset pinhole at the side of the NP124. Use a paper clip and press inside for 15 seconds.

3. The default settings will be restored where the DHCP would be enabled. You would then be able to

navigate to http://192.168.20.1 in a web browser.

Setting a static IP address on your computer

Refer to this image for Windows Computers

Below are the instructions for setting Windows XP to set a static IP address for your ethernet connection:

1. Click on the Start Menu, and go to “Control Panel”.

2. Click on “Network Connections”.

(If you only see "Network and Internet Connections", open that first, and then click on "Network

Connections".)

3. Right click on “Local Area Connection” and select “Properties”.

4. Double-click on “Internet Protocol”.

5. Select "Use the following IP address ".

6. Type in the following information

IP address: 192.168.20.100

Subnet mask: 255.255.255.0

Default gateway: 192.168.20.1

7. Click “OK”, and then click “OK”(or “Close”).

Below are the instructions for setting Windows Vista to obtain an IP address automatically for your ethernet

connection:

1. Click on the Start Menu, and go to “Control Panel”.

2. Click on “Network and Sharing Centre”.

(If you only see "Network and Internet", open that first, and then click on "Network and Sharing Centre".)

3. Click on “Manage network connections” (on the lefthandside of the window).

4. Right click on “Local Area Connection” and select “Properties”.

5. Double-click on “Internet Protocol Version 4 (TCP/IPv4)”.

6. Select "Use the following IP address ".

7. Type in the following information

IP address: 192.168.20.100

Subnet mask: 255.255.255.0

Default gateway: 192.168.20.1

8. Click “OK”, and then click “OK”(or “Close”).

Below are the instructions for setting Windows 7 to obtain an IP address automatically for your ethernet

connection:

1. Click on the Start Menu, and go to “Control Panel”.

2. Click on “Network and Sharing Centre”.

(If you only see "Network and Internet", open that first, and then click on "Network and Sharing Centre".)

3. Click on “Change adapter settings” (on the lefthandside of the window).

4. Right click on “Local Area Connection”and select “Properties”.

5. Double-click on “Internet Protocol Version 4 (TCP/IPv4)”.

6. Select "Use the following IP address ".

7. Type in the following information

IP address: 192.168.20.100

Subnet mask: 255.255.255.0

Default gateway: 192.168.20.1

8. Click “OK”, and then click “OK”(or “Close”).

Refer to this image for Mac OS X Computers

Below are the instructions for setting Mac OS X to obtain an IP address automatically for your ethernet

connection:

1. Click on the Apple Menu, and go to "System Preferences".

2. Click on "Network".

3. Click on “Ethernet” or "Built-in Ethernet".

4. Click on the "Configure"drop-down box, and select "Manually”

5. Type in the following information

IP Address: 192.168.20.100

Subnet Mask: 255.255.255.0

Router: 192.168.20.1

6. Click “Apply”.

Note: If you are still unable to open the configuration page, try a different web browser (i.e. Google

Chrome, Mozilla Firefox, etc.) or a different computer.

Table des matières

Autres manuels NetComm Wireless Routeur réseau

NetComm Wireless

NetComm Wireless NTC-400 Series Manuel utilisateur

NetComm Wireless

NetComm Wireless NTC-220 Series Manuel utilisateur

NetComm Wireless

NetComm Wireless NWL-12 Series Manuel utilisateur

NetComm Wireless

NetComm Wireless NTC-6908 Manuel utilisateur

NetComm Wireless

NetComm Wireless 3G29WN2 Manuel utilisateur

NetComm Wireless

NetComm Wireless NB304n Manuel utilisateur

NetComm Wireless

NetComm Wireless NTC-6200-01 Manuel utilisateur

NetComm Wireless

NetComm Wireless NTC-400 Series Manuel utilisateur

NetComm Wireless

NetComm Wireless NB16DG Mode d’emploi

NetComm Wireless

NetComm Wireless NF10WV Manuel utilisateur

NetComm Wireless

NetComm Wireless NTC-221 Manuel utilisateur

NetComm Wireless

NetComm Wireless NTC-140-01 Manuel utilisateur

NetComm Wireless

NetComm Wireless NF1ADV Manuel utilisateur

NetComm Wireless

NetComm Wireless NTC-225 Manuel utilisateur

NetComm Wireless

NetComm Wireless NF10WV Manuel utilisateur

NetComm Wireless

NetComm Wireless NTC-6200 Manuel utilisateur

NetComm Wireless

NetComm Wireless NF15ACV Manuel utilisateur

NetComm Wireless

NetComm Wireless NF10WV Manuel utilisateur

NetComm Wireless

NetComm Wireless NB304n Manuel utilisateur

NetComm Wireless

NetComm Wireless NTC-6908 Instructions d'installation

NetComm Wireless

NetComm Wireless NTC-140W Manuel utilisateur

NetComm Wireless

NetComm Wireless NF18ACV Manuel utilisateur

NetComm Wireless

NetComm Wireless NB16DG Manuel utilisateur

NetComm Wireless

NetComm Wireless NF10W Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité