Neopost SI30 Manuel utilisateur
QUICK INSTALLATION GUIDE
Prior to installation
This equipment must be installed on a piece of furniture or desk near a
220V power socket. Align the front of the machine with the edge of the
desk in order to position the receptacle correctly.
Do not connect the machine to the mains supply before reaching stage G.
1 - INSTALLATION
Check contents: see following list
A
Remove the protective cardboard from the insert feeder (feeder C).
B
n1 folder-inserter
1 document feeder
4 transparent document holders
2 rear guides for the envelope hopper
1 power lead
1 catch tray
1 quick installation manual
1 user manual
o
p
u
r
s
t
q
n
o
p
q
s
Grip the opening lever at the back of the machine
to tilt the tray backwards.
Rear view
n
Carefully remove the blocking cardboard from the
rollers then close the feeder.
o
r
Remove the two protections located inside the base.
C
Filling the water tray.
D
Carefully remove the sheet of white paper then the
blocking cardboard from the roller. Proceed to the
following paragraph before closing the machine.
n
o
p
p
Open the machine by pressing the handle
located at the front.
Carefully remove the water tray using its blue handles.
Remove the triple stopper strip and fill all 3 openings with water up to the
level mark then replace the stoppers. Check that brushes are fully
moistened. Replace the water tray in its housing keeping the blue handles
pointing towards you. Close the top cover.
Stopper strip
Water tray
n
op
Installing the machine.
E
Control panel
H
Connecting the power cord
FInstalling the catch tray
G
Clip in the rear guides for
the envelope hopper,
pushing them in properly.
Make sure that they are
positioned correctly.
Position the document
feeder by engaging its 2
plastic lugs into their res-
pective slots located on the
machine base.
Hold the feeder pointing
towards you, plug in the
connector, then replace the
feeder on the base.
Clip in the transparent docu-
ment holders for feeders A
and B.
n
o
p
q
Plug the power cord into
the back of the machine,
then connect to the mains
supply.
Rear view
Clip the catch tray to
the machine front
feet
n
o
q
Display
field
Selection key
p
Memory key Escape key
r
Stop/Start key
s
Scroll keys
Starting the machine: first run
I
Entering code: first run.
J
The machine’s user default language is set to English. This can be changed by
holding down the key and pressing the ON/OFF switch located at the back of
the machine.
n
o
Select the “language” field using the key
Use the keys to change the language setting q
pPress to store changes
Press to return to the user menu
For security reasons, the machine is protected with a code. This code must be entered the first time the machine is
used. Each machine is assigned a unique code sequence.
It is made up of 10 numbers and should be entered using the following screen:
nPress to display the correct number in
the designated position
oPress to validate the number
(the cursor will proceed to the following number automatically)
pRepeat steps 1 and 2 until the full code has been
entered! (10 numbers).
! Don’t forget to validate the last number using the key
before saving the code.
qIn the event of an input error, press
and repeat the procedure from stagen
rOnce the code has been entered correctly, save
by pressing
The machine is ready for use.
Enter the code in this direction
ESC
ESC
ESC
STA RT
STOP
STA RT
STOP
AUTHORIZATION CODE SET UP
: Select number
START-STOP : Validate number
ESC : exit
Press to confirm
Code : 0000000000
MACHINE SETUP
Serial Number : 0000000000
Press to confirm
CONFIGURATION MACHINE
Numéro Machine : 0000000000
Appuyer sur pour continuer
Language : ENGLISH
Set : Env. / Doc.
Double Det. Bin C : DISABLE
Langue : FRANCAIS
Personnalisation : Env. / Doc.
Det. Double Bac C : DEVALIDER
2 - USE
Selecting a job
K
Loading documents (feeders A and B)
M
Loading envelopes
L
The machine is ready for use when the following menu is displayed.
The job function makes it possible to define and store the format of the main envelope and the document figuring
the address, and to define the appropriate feeder selection for the application to be processed.
n
o
Select the “job number” field by holding down the key
until it is highlighted.
Use the keys to select a job number.
pCheck the contents of the 9 pre-configured jobs and
select the one which corresponds to the application to
be processed, or modify the required field to adapt a job.
Then proceed to the next steps.
Envelopes must be loaded printable side up with the flap at the top as in the following diagram.
Adjust the guides to fit
the envelope format.
n
o
Unlock the side guides
lever (in position) and
open the side guides.
Load the envelopes
according to this
diagram.
p
q
Move the guides to the
width of the envelopes
so that they rest lightly
against the envelope
stack, and lock the
lever. (in position)
Large format documents must be loaded vertically, in reading direction with the address-face pointing towards the
user according to the following procedure.
Release the pressure
units
n
o
Load documents
vertically
Adjust the side guides to
rest lightly against the
document stack and lock
p
qLock the pressure units
READY : START to process a job
or to select line to modify
Counter : 1 2 3 4
Job number : 02
Feeder : AUTO A+B+C
Document : A4 (297 mm)
Envelope : C6/5 DL CLOSED
Address height : +0 mm
Loading inserts and reply envelopes (feeder C)
N
Lift the pressure unit and
hold it up while sliding the
stack of inserts or reply
envelopes into the
feeder.
nRelease the pressure
unit and adjust the side
guides to rest lightly
against the document
stack.
o
Reply envelopes must be loaded with their
flaps closed and pointing downwards (as in
the following diagram).
OR
Starting a Job
O
The job has been selected, documents and envelopes are loaded…
nProcess a test envelope by pressing twice.
oCheck that the address is positioned correctly in
the envelope window and adjust if necessary.
A-Select the address position field using the
key.
B-Raise/lower the address using the key.
pStore the job if necessary by pressing the key
qSettings are satisfactory, press to start the
envelope-filling process.
M. P. Robert
1, rue des arbres
75001 Paris
M. P. Robert
1, rue des arbres
75001 Paris
For further details regarding the functions of this product, or if problems are encountered during installation, please refer to
the user manual or contact the Neopost Help desk.
CONGRATULATIONS!
START
STOP
Neopost Limited, Neopost House, South Street, Romford, Essex RMI 2AR
Customer Service: (01708) 714111 Fax: (01708) 714142
Website: www.neopost.co.uk
STA RT
STOP
01/02/2006 - 4124886F/D
Table des matières
Autres manuels Neopost Plieuse
Neopost
Neopost DS-75 Manuel utilisateur
Neopost
Neopost PF-55 Manuel utilisateur
Neopost
Neopost DS-85 Manuel utilisateur
Neopost
Neopost SI 72 Manuel utilisateur
Neopost
Neopost PF-75 Manuel utilisateur
Neopost
Neopost Carat Prisma Manuel utilisateur
Neopost
Neopost PF-90 Manuel
Neopost
Neopost SI60 Manuel utilisateur
Neopost
Neopost PF-45A Manuel utilisateur
Manuels Plieuse populaires d'autres marques
Mathias Bauerle
Mathias Bauerle Multipli 35 Manuel utilisateur
Intelli-Fold
Intelli-Fold DF-304C Manuel utilisateur
Pitney Bowes
Pitney Bowes DI425 FastPac Manuel
Hwasung
Hwasung COMPODIS HMK-830 Series Manuel utilisateur
KRUG+PRIESTER
KRUG+PRIESTER IDEAL 8306 Manuel utilisateur
XPOtool
XPOtool 61574 Manuel utilisateur
