Count KF-250 Manuel utilisateur

KF-250

Knife Folding Machine

Serial Number ___________________________

Date ___________________________________

Page left blank intentionally

Table of Contents

INTRODUCTION ............................................................................................................................... 5

PREFACE....................................................................................................................................... 5

SPECIFICATIONS........................................................................................................................... 5

ELECTRICAL SPECIFICATIONS........................................................................................................... 6

SAFETY PROCEDURES ...................................................................................................................... 6

BEFORE USE:................................................................................................................................ 6

DURING USE: ............................................................................................................................... 6

AFTER USE: .................................................................................................................................. 6

CARE AND MAINTENANCE............................................................................................................... 7

BEARINGS/BUSHINGS:................................................................................................................. 7

SENSOR EYE: ................................................................................................................................ 7

KEEP THE ROLLERS CLEAN: .......................................................................................................... 7

IMPORTANT NOTES BEFORE OPERATING THE KF-250.................................................................... 7

DOUBLE FEEDING: ....................................................................................................................... 7

KNOB SETTINGS:.......................................................................................................................... 7

START DELAY: .............................................................................................................................. 7

COMPONENT IDENTIFICATION........................................................................................................ 8

SETTING UP YOUR KF-250 ............................................................................................................... 9

DELIVERY TRAY INSTALLATION.................................................................................................... 9

BI-PASS TRAY INSTALLATION..................................................................................................... 10

PAPER STOP ASSEMBLIES .......................................................................................................... 10

MACHINE OPERATION................................................................................................................... 11

MAIN POWER ............................................................................................................................ 11

TOUCH SCREEN CONTROLLER ....................................................................................................... 12

TOUCH SCREEN OPERATION...................................................................................................... 12

COUNT LOGO AND SERVICE ACCESS ......................................................................................... 12

AUTO SETUP SCREEN................................................................................................................. 13

PAPER THICKNESS...................................................................................................................... 13

KNOB SETTINGS / GAP ADJUSTMENT........................................................................................ 14

MEASURE SHEET........................................................................................................................ 15

RUN SCREEN .............................................................................................................................. 15

MICRO ADJUSTING THE FOLD POSITION................................................................................... 16

REPEAT LAST JOB....................................................................................................................... 16

TRANSPORT OPERATION ........................................................................................................... 17

AUTO FOLD SETUP......................................................................................................................... 17

HALF FOLD SETUP:..................................................................................................................... 17

TRI-FOLD SETUP:........................................................................................................................ 18

Z FOLD SETUP: ........................................................................................................................... 18

LETTER FOLD SETUP: ................................................................................................................. 18

GATE FOLD SETUP: .................................................................................................................... 18

DOUBLE PARALLEL FOLD SETUP:............................................................................................... 19

MANUAL SETUP......................................................................................................................... 19

SAVING MANUAL FOLD JOBS .................................................................................................... 20

RECALLING MANUAL FOLD JOBS............................................................................................... 20

FEED TABLE ASSEMBLY.................................................................................................................. 21

FEED TABLE ASSEMBLY (bottom) .............................................................................................. 22

ADJUSTING THE FEED RAIL ........................................................................................................ 23

LOADING THE FEEDER ............................................................................................................... 23

SETTING THE AUTOMATIC FEEDER............................................................................................ 24

CONTINUOUS FEEDING ............................................................................................................. 24

FEEDING NOTES......................................................................................................................... 25

DELIVERY TABLE............................................................................................................................. 25

CHECKING THE SENSORS ........................................................................................................... 26

ROTATING PLASTIC COVER........................................................................................................ 26

TROUBLE SHOOTING ..................................................................................................................... 27

INTRODUCTION

PREFACE

The KF-250 is a precision folding machine. With its intuitive touchscreen design, it can perform 6

different types of automated setup folds of pre-creased paper. It has a manual feature that

allows for the fold to be placed virtually anywhere on the sheet. When properly setup and using

pre-creased sheets, the knife blade folding mechanism will prevent the cracking of digitally

printed material when folded. The independent feeder allows the machine to be a stand alone

solution for creased paper coming off any type of creasing machine. It is very important to keep

it free of excessive dust, dirt and foreign matter. We recommend that you keep the machine

covered when not in use.

SPECIFICATIONS

Net Weight: KF-250………………………………………………………..224 lbs

Overall Dimensions: ………………………………………………………………….67”Lx28”Wx47”H

Boxed Dimensions: ………………………………………………………………….49”Lx34.5”Wx52.5”H

Boxed Weight: ………………………………………………………………….395 lbs.

Min. Sheet Size: .……………………………………………………….………..4.75”x5.5”

Max. Sheet Size: ….………………………………………………………………14.5”x33”

Paper Weight Range: (gsm) …………………………………………………………….120-350

Max Speed: (sheets per hour) …………………………………………………………4,600

ELECTRICAL SPECIFICATIONS

Power Requirement: 110v/60 HZ or 220v/50 HZ, AC 20 AMP

Circuit Protection: 20/5 AMP Circuit Breaker

NOTE: Older buildings, overloaded lines, and bad grounds can affect the operation of your KF-

250. A regulated dedicated line is recommended. Operating the machine through a power

strip is not recommended.

SAFETY PROCEDURES

BE ALERT! BE CAREFUL!

BEFORE USE:

Read through the owner’s manual. Follow instructions CAREFULLY.

Do not install the machine on uneven ground.

NEVER use in a wet area. Electric shock could occur.

Use at least a 20 amp power source at 110 vac.

Use a GROUNDED outlet and a GROUNDED circuit. Do not use ungrounded

equipment on the same circuit.

Always use a dedicated line. DO NOT use with line splitting surge protector.

Make sure all safety covers are in place. The top cover has an interlock switch which

will disable the unit if in the up or open position.

Open and close the plastic cover slowly.

DURING USE:

Exercise caution with long hair and loose fitting clothes when near the machine nip

in operation.

Keep fingers and hands away from belts, folding blades, and rubber rollers.

Keep fingers away from any moving part.

Keep cords clear of moving parts.

Do not place any liquid on any surface of machine.

Do not put heavy matter on machine.

AFTER USE:

Turn off machine at the side cover, then unplug the main power cord. This will

prevent damage to your machine by power/voltage spikes.

To unplug cords, always grasp the plug body, never pull on cords to disconnect.

Wire fatigue and possible shock could result from improper disconnect procedures.

Disconnect the power before cleaning the inner machine.

Clean all rollers, belts and moving parts.

Cover the Machine.

CARE AND MAINTENANCE

The KF-250 is a precision machine. It is very important to keep it free of excessive dust, dirt and

foreign matter. We recommend that you keep the machine covered when not in use.

BEARINGS/BUSHINGS: The bearings are sealed roller bearings and are designed to be self

lubricating. However, dirt and dust can get into them causing clogging and dirt build up. It is

recommended to oil them weekly under heavy use or monthly under light use. The bushings for

the knife blades are Bronze and require lubrication more frequently. Oil these once a week

under heavy use with a light machine oil or 3-1 oil.

SENSOR EYE: Clean the lower reflector tape located on the plate under the infeed register

regularly. Clean with water damp rag only. Dust will cause the beam to reflect incorrectly. Clean

when necessary.

KEEP THE ROLLERS CLEAN: Excess paper dust will cause slippage of the paper. You must

clean the rollers regularly to ensure good registration. To do this, unplug the machine carefully,

lift plastic cover, and use a clean wet rag with water only and clean each roller. If you do keep

your KF-250 clean and in top condition, it will give you years of service.

IMPORTANT NOTES BEFORE OPERATING THE KF-250

To ensure the smooth operation of this machine please read the following. If you do not

understand these sections of how to operate the machine you may cause damage and

unintentionally void your warranty.

DOUBLE FEEDING: The KF-250 is designed to run a single sheet. If a double sheet is fed

through the machine, it will lock up. If the machine is not turned off immediately, you may

cause damage to the motor driver and void the warranty.

KNOB SETTINGS: The knob settings are directly related to how well the machine will run.

Please read the section on Knob settings before operation.

START DELAY: When pressing the RUN button there is a 2 second delay for the transport

motor to turn as the knife blades preform a homing cycle.

COMPONENT IDENTIFICATION

REFERENCES

Note: We are continuously improving and changing the machine. Specifications and

information in this manual are updated as per the change and without any notice.

Feed Table Assembly

Delivery Tray

Motorized Delivery

Paper Stop

Delivery Tray Pg. 9

Power Switch Pg. 11

Touch Screen Pg. 12

Gap Settings Pg. 14

Feed Table Assembly Pg. 21

Feed Guide Rail Pg. 21

Motorized Delivery Pg. 25

Feed Guide Rail

Touch Screen

Power Switch

Gap Knobs

SETTING UP YOUR KF-250

This machine is 90% ready to go when it arrives on your dock. There are only a few items that

need to be put into position before it is ready to use. Those items are below:

DELIVERY TRAY INSTALLATION

The motorized delivery is recommended to be installed by two people but can be done with one

although it is more difficult. Locate the exit support shaft of the machine. Install the hooks on

the delivery tray to the cuts outs show on the shaft below, now support the end of the tray and

position the arms into the larger slots on the exit panel.

Upper Position shown below

Plug delivery table into matching power receptacle on folder cover. Warning: Do not plug

delivery table to any other power source!

Cut outs on shaft for

delivery mounting

BI-PASS TRAY INSTALLATION

As shown below, there are hooks that hold the bi-pass tray into position. If the magnetic paper

stops have already been placed, you should remove them for easier installation of the tray.

First, angle upward and insert the upper hooks into the upper slots and then rotate downward

to place the lower hooks into the lower slots.

PAPER STOP ASSEMBLIES

There are two different paper stops. One will have a bend and one will be straight. The straight

paper stop is the rear or back paper stop. The bent paper stop is the operator side paper stop.

There is no paper stop for the non-operator side. The support arm acts as the stop for that side.

They hold their position using a magnet which makes it easy for adjustment. The positions for

the paper stops will change for each individual job. If the paper stops are set too close the

paper will hit them as it exits the machine and will cause a paper jam. If they are set too loose,

the paper will stack in an unorganized manner. Getting the position correct is imperative to

smooth operation of the machine.

Table des matières

Autres manuels Count Plieuse

Count

Count KF-200 Manuel utilisateur

Manuels Plieuse populaires d'autres marques

Mathias Bauerle

Mathias Bauerle Multipli 35 Manuel utilisateur

Intelli-Fold

Intelli-Fold DF-304C Manuel utilisateur

Pitney Bowes

Pitney Bowes DI425 FastPac Manuel

Hwasung

Hwasung COMPODIS HMK-830 Series Manuel utilisateur

KRUG+PRIESTER

KRUG+PRIESTER IDEAL 8306 Manuel utilisateur

XPOtool

XPOtool 61574 Manuel utilisateur

MBM

MBM 306A Manuel utilisateur

Formax

Formax FD 342 Manuel utilisateur

Formax

Formax FD 332 Manuel utilisateur

MBM

MBM FO0601 Manuel utilisateur

IMS

IMS FPi4000 Manuel utilisateur

Nagel

Nagel Foldnak 80 Manuel utilisateur

MBM

MBM S 352 Manuel utilisateur

Formax

Formax AutoSeal FD 1500 Plus Manuel utilisateur

Opus

Opus multiCREASE 52 Manuel utilisateur

KRUG+PRIESTER

KRUG+PRIESTER IDEAL 8306 Manuel utilisateur

Martin Yale

Martin Yale 1217a Manuel utilisateur

Horizon Fitness

Horizon Fitness SPF-20A Manuel utilisateur