Neomatica ADM333 BLE Manuel utilisateur

«Neomatica»Ltd. Vehicle tracker ADM333 GLONASS/GPS. Ver.1.2 dd 13.09.2019

 
«Neomatica»Ltd. Vehicle tracker ADM333 GLONASS/GPS. Ver.1.2 dd 13.09.2019 

Content 
 
Purpose and function ..........................................................................................................................................4 
Technical specifications ....................................................................................................................................5 
Design.........................................................................................................................................................................7 
1 Disassembling and assembling of the housing ................................................................................................8 
Installation ...............................................................................................................................................................9 
Tracker setting............................................................................................................................................................10 
1 Connection to ADM configurator ......................................................................................................................10 
2 Configuration using commands........................................................................................................................11 
3 Configuring SIM ..................................................................................................................................................13 
4 Setting connection to the server.......................................................................................................................13 
5 Setting data transmission..................................................................................................................................14 
6 Setting route (track) drawing.............................................................................................................................14 
6.1 Selecting presets of route drawing quality...............................................................................................14 
6.2 Expert setting of tracking parameters.......................................................................................................15 
7 Setting the fixation (freezing) of coordinates during the parking..................................................................17 
7.1 Coordinates fixation according to ignition...............................................................................................17 
7.2 Coordinates fixation according to vibration level....................................................................................18 
8 Operation mode...................................................................................................................................................19 
8.1 “Tracker” operation mode ..........................................................................................................................19 
8.2 “Beacon” operation mode ..........................................................................................................................19 
Connection of extra devices .....................................................................................................................................20 
1 Analogue inputs..................................................................................................................................................20 
2 Discrete output....................................................................................................................................................21 
3 RS-485..................................................................................................................................................................22 
3.1 Connection of digital fuel level sensor......................................................................................................22 
4 1-Wire ...................................................................................................................................................................24 
4.1 Connection of temperature sensors..........................................................................................................24 
4.2 Connection of iButton.................................................................................................................................24 
Commands description .............................................................................................................................................26 
Updating tracker software.........................................................................................................................................34 
1 Updating tracker software via ADM Configurator ...........................................................................................34 
2 Updating tracker software via ADM Configurator using a firmware file .......................................................34 
3 Updating the tracker software via GPRS..........................................................................................................35 
Handling and transportation regulations.................................................................................................................35 
Warranty obligations .......................................................................................................................................35 
Marking and packaging ...........................................................................................................................................36 
Disposal.....................................................................................................................................................................36 
Scope of supply........................................................................................................................................................36 
Acceptance certificate .............................................................................................................................................36 
Appendix A. Description of the bits of the field «STATUS» .....................................................................................37 
Appendix B. Description of transmitted parameters in Wialon................................................................................38 
 

«Neomatica»Ltd. Vehicle tracker ADM333 GLONASS/GPS. Ver.1.2 dd 13.09.2019

This Operation manual relates to the vehicle tracker ADM333 (hereinafter referred to as

tracker) and describes the procedure of its installation and connection as well as its function and

settings.

The Operation manual is designed for professionals who have familiarized themselves with the

rules of repair and installation works execution in vehicles and who have special professional

knowledge in electronic and electric equipment used on various transport means.

The tracker proper work can be guaranteed if it is installed and set by qualified professionals.

To use the tracker properly it is necessary to familiarize with the monitoring system work principles

in general and to understand the function of all its components. For this reason, it is strictly

recommended to get basic knowledge on GLONASS and GPS global navigation satellite systems

functioning, GSM network, issues related to data transmission by means of short message service

(SMS), GPRS and Internet.

«Neomatica»Ltd. Vehicle tracker ADM333 GLONASS/GPS. Ver.1.2 dd 13.09.2019

1 Purpose and function

The tracker is intended for installation on a vehicle as an additional device that records the

location of the vehicle, its speed, and travel direction.

Additionally, the voltage level at theanalogue inputs and data received from supported devices

connected via RS-485 and1-Wire are recorded as well. All eventsand conditions fixed by the tracker

are stored in its non-volatile memory.

The accumulated data is transmitted through the GSM 850/900/1800/1900 cellular network

operator using packet data transmission technology GPRS to a dedicated server with a static IP

address or domain name from which it can be received via the Internet for further analysis and

processing in a monitoring center.

View of the tracker is shown in Figure 1.

The tracker can be configured in any convenient way: locally (via Bluetooth, using the ADM

Configurator (hereinafter referred to as Сonfigurator) or remotely (by sending commands via SMS

or GPRS).

To ensure data security, when the external power is turned off and the GSM network is lost,

the tracker has a non-volatile memory. Data transmission is possible only if there is a GSM

850/900/1800/1900 cellular network supporting a packet data service (GPRS).

Figure 1 –View of the tracker

The vehicle travel route is described in the form of separate points in time. The route point is

saved when at least one event occurs, such as:

⎯travel direction changes by an angle which is greater than the pre-set one;

⎯the straight-ahead travel is performed at a distance, which is longer than the pre-set

one;

«Neomatica»Ltd. Vehicle tracker ADM333 GLONASS/GPS. Ver.1.2 dd 13.09.2019

⎯the pre-set acceleration limit is broken;

⎯the time for putting the point while traveling (parking) is expired;

⎯device status change (description is given in Appendix А. Description of the bits of

the field «STATUS» );

⎯an event occurs on analogue input.

In this way, route points might be saved with the time interval from one second to several

minutes allowing for a quality routing, recording any changes without a surfeit of information saved

in the “black box” and increase in GPRS traffic.

After being connected to the power supply, the tracker starts receiving data from GLONASS

and/or GPS satellites, locating itself, identifying time, speed, travel direction, and in case of GSM

network availability establishes connection with the server. After being connected to the server, the

tracker transmits thereto the data packets with the pre-set frequency or when an event occurs. If for

any reason the connection to the server fails, all the information will be saved in the tracker non-

volatile memory and transmitted as soon as the connection is restored.

If there is no signal from GLONASS and/or GPS satellites and there is GPRS connection the

time is synchronized via NTP protocol with one of the available public servers. The points will be

recorded without data about location.

Data transmitted by the tracker:

⎯GMT date and time;

⎯coordinates (latitude, longitude, altitude);

⎯speed, acceleration and travel direction;

⎯number of satellites when fixing a navigation problem;

⎯precision loss factor in a horizontal plane;

⎯voltage values on analogue inputs

⎯data about events occurred;

⎯device status;

⎯data from the sensors connected to RS-485 and 1-Wire.

2 Technical specifications

⎯GLONASS/GPS receiver:

chipset: МТ3333 (MediaTek);

frequency bands: GLONASS –L1 (СT-code), GPS - L1 (С/Аcode);

«Neomatica»Ltd. Vehicle tracker ADM333 GLONASS/GPS. Ver.1.2 dd 13.09.2019

sensitivity in cold start/tracking, dBm: - 149 dBm/- 167;

number of tracking/picking-up channels: 33/99

positioning precision, 95% of time, not worse: 3 m

⎯Connection standard: GSM 850/900/1800/1900, GPRS Multi-slot Class 12.

⎯GSM transmitter power: 2 W

⎯Number of SIM-cards, form factor: 2, nano-SIM (4FF).

⎯Number of analogue inputs: 2.

⎯Analogue inputs features:

⎯voltage measurement range: 0..58,8 V

⎯discreteness (sensitivity): 57,4 mV

⎯input resistance: 200 кOhm.

⎯Number of discrete outputs of “open collector”: 1.

⎯Characteristics of discrete output of “open collector” type”:

⎯maximum voltage –45V;

⎯maximum commutated current –100mA.

⎯Interface RS-485: 1.

⎯Interface 1-Wire: 1.

⎯Acceleration meter: digital, triaxial

⎯Battery: Li-Pol 250 мА/h 3.7V (0,9 W/h).

⎯Number of stored root records: at least 30 000.

⎯PC connection interface: Bluetooth 3.0.

⎯Operation temperature:

⎯with a battery: - 20...+60°С;

⎯without a battery: - 40...+85°С.

⎯Power voltage: +8...+45 V of unregulated direct current

⎯Current consumption (at the supply voltage 12 V):

⎯maximum: 200 mА

⎯average: 30 mА

⎯Dimensions: 55х49х20mm;

⎯weight: not more than 39 g

«Neomatica»Ltd. Vehicle tracker ADM333 GLONASS/GPS. Ver.1.2 dd 13.09.2019

3 Design

Functionally, the tracker consists of a microcontroller, non-volatile memory, a combined

GLONASS/GPS-, GSM-, Bluetooth module, analog inputs, discrete output, digital interface RS-485,

digital interface 1-wire, acceleration meter.

The GLONASS/GPS unit of the combined module is designed to receive signals from the

GLONASS/GPS satellites and determine the geographical coordinates of the receiver antenna

(latitude, longitude and altitude), as well as the exact time (GMT), speed and direction of travel.

GSM/GPRS unit of the combined module performs the following functions:

⎯establishment and maintenance of outgoing TCP/IP connection (data reception and

transmission in GPRS mode);

⎯reception and sending SMS messages.

For information transmission, the GSM/GPRS unit of the combined module establishes and

maintains a connection to the server, periodically transmitting information packets. The periods of

data transmission to the server during the parking and during the movement of the vehicle are

different and can be changed by user.

Bluetooth unit of the combined module provides connection to the PC, as well as wireless

information exchange between the tracker and the ADM Сonfigurator.

To display the operating status, the tracker has 2 LED indicators: green and blue

The green LED indicates the status of the GLONASS/GPS unit of the combined module:

⎯flashes three times–the GLONASS/GPS unit is on, but there is no data from it;

⎯flashes twice –data from the GLONASS/GPS unit received, but the coordinates are

invalid;

⎯flashes once –the GLONASS/GPS unit has determined the time and the actual

coordinates.

The blue LED indicates the status of the GSM/GPRS unit of the combined module:

⎯flashes three times - the GSM/GPRS unit is disabled for re-initialization;

⎯flashes twice - the GSM/GPRS unit is on, but there is no connection to the server;

⎯flashes once - the tracker has established connection to the server and successfully

transmits the information packets;

«Neomatica»Ltd. Vehicle tracker ADM333 GLONASS/GPS. Ver.1.2 dd 13.09.2019

⎯constantly shines, briefly turning off - SIM card is not available.

The scheme of tracker connector pins is given in Fig. 2

Fig.2 –Scheme of pins location

3.1 Disassembling and assembling of the housing

There are logo and LEDs on the upper part of the housing.

There is a sticker with marking on the lower part of the housing.

The disassembling should be done as follows:

1. Place the housing on a solid surface in such a way the logo to be upwards

2. Insert a card into the gap at the angle of 45 degrees until the housing starts splitting

Do not split two parts of the housing at this stage.

3. Insert a card into the gap from the other side of the housing at the angle of 45 degrees until

the housing starts splitting.

4. Take off the lower part of the housing

5. Bending two latches on any side of the housing lift the scheme up and gently remove it

without damaging the wires and the built-in battery.

The assembling should be done in the reverse order:

1. Make sure the wires of the battery are not squeezed and then install the scheme

2. Pressing to the scheme alternately from both the sides clamp the scheme holders

3. Install the upper part of the housing.

«Neomatica»Ltd. Vehicle tracker ADM333 GLONASS/GPS. Ver.1.2 dd 13.09.2019

4 Installation

It is strongly recommended to carry out a preliminary check of the tracker before installation,

using a power supply different from the vehicle on-board power, with an output voltage from 8 V to

40 V DC and a current of at least 1 A.

The tracker has got internal GLONASS/GPS and GSM antennas so can be installed almost in

any place of the vehicle. However, it isnot recommended to install it in the places wherethe received

signals will be attenuated by the vehicle metallic housing, since this may affect the tracker working

quality. For a proper function of the GLONASS/GPS receiver, put the tracker in such a way when its

sticker is directed upwards.

Insert a SIM card with a deactivated PIN code request, activated data transmission service via

GPRS, SMS and sufficient balance for these services into the holder SIM0 or SIM1.

Supply the power to the tracker according to the layout in Figure 3 and the scheme of pins

location in Figure 2. When connecting the plus of the vehicle network to the tracker, install a 2A

fusible as close as possible to the point of connection to the vehicle network, which is especially

important when connecting directly to the battery clamp.

Figure 3 –Standard connection layout of the tracker

If there are valid satellite data and an established connection to the server, the tracker will

catch the time, coordinates and transmit information packets to the server, which will be marked by

a single flashing of the green and blue LEDs.

«Neomatica»Ltd. Vehicle tracker ADM333 GLONASS/GPS. Ver.1.2 dd 13.09.2019

5 Tracker setting

5.1 Connection to ADM configurator

To connect the ADM333 tracker to a personal computer using Bluetooth wireless technology,

you should do the following:

1) Bring the Bluetooth adapter of the PC to the working state;

2) Activate the ADM Configurator program of the version 2.4.3 or later (available for loading in

website http://neomatica.com);

3) Switch the ADM Configurator to the Bluetooth radio connection mode. To do this, you need

to select the way of device connection by clicking on the Bluetooth icon in the upper left

corner of the ADM Configurator, as shown in Figure 4;

4) Supply power to the tracker;

5) If there are several active trackers within the reach of the Bluetooth adapter of the personal

computer, select the "Select device" flag and enter the last 4 digits of IMEI as shown in

Figure 5. If there is only one active tracker within the reach of the Bluetooth adapter of the

personal computer it is possible to remove “Select device” flag. In such a case a random

tracker from all the detected ones will be connected.

Figure 5 –ADM Configurator waiting for device connection

6) After a few seconds the connection between the tracker and the ADM Configurator

program will be installed and the settings window will be displayed;

Autres manuels pour ADM333 BLE

Table des matières

Autres manuels Neomatica GPS

Neomatica

Neomatica ADM333 BLE Manuel utilisateur

Neomatica

Neomatica ADM50 Manuel utilisateur

Neomatica

Neomatica ADM500 Manuel utilisateur

Neomatica

Neomatica ADM100 Manuel utilisateur

Neomatica

Neomatica ADM700 3G Manuel utilisateur

Neomatica

Neomatica ADM007 Manuel utilisateur

Neomatica

Neomatica ADM333 Manuel utilisateur

Manuels GPS populaires d'autres marques

Raven

Raven Cruizer II Manuel

Hama

Hama 53118 Manuel utilisateur

Garmin

Garmin SOUNDER 125 Manuel utilisateur

Garmin

Garmin DEZL 580 Manuel utilisateur

Jigabot

Jigabot EX Manuel utilisateur

Pointer

Pointer Cellocator CelloTrack XT LTE Guide d'installation

Queclink

Queclink GV55LITE Manuel utilisateur

Voxson

Voxson Voxtrack GPS500 Manuel d'instructions

Garmin

Garmin ECHOMAP PLUS Manuel utilisateur

Starcom Systems

Starcom Systems Kylos Compact Manuel utilisateur

Garmin

Garmin 15 H Series Manuel utilisateur

Cobra

Cobra Marine MC 600Ci Manuel utilisateur

Cellocator

Cellocator CelloTrack T Manuel utilisateur

Enfora

Enfora Mini-MT GSM2228UG001 Manuel utilisateur

Magellan

Magellan eXplorist 100 Manuel utilisateur

LTE

LTE G50B Manuel utilisateur

Garmin

Garmin DEZL OTR500 Manuel utilisateur

SkyGolf

SkyGolf SkyCaddie SG1 Manuel utilisateur