NEO BOMBER Manuel utilisateur
USER MANUAL / MANUAL DE USUARIO
PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE
POR FAVOR LEA LAS INSTRUCCIÓNES ANTES DE USAR
BOMBER
powerful and versatile effect
powered by a 5R lamp
BOMBER
ENGLISH VERSION
p. 2
Overview
Blast 5R is a powerful and versatile eect powered by a 5R
lamp and four independently controlled mirrors. This unit al-
lows a wide coverage and it has a wheel with 7 dichroic lters
plus a 14 rotating gobo wheel. Blast 5R comes with a 0-100%
linear dimmer, strobe eect and it can be controlled in 4 dif-
ferent ways (DMX, Sound- active, Master/Slave and Auto-run).
A powerful eect for when classic applications become more
demanding.
Specications
Source & Optics
Light Source: 1 5R Lamp (189W) Lamp life: 4,000 hours
Eects & Functions
4 independently controlled mirrors Color wheel: 7 dichroic
lters + open Rotating gobo wheel: 14 rotating gobos + open
Gobo Shake Dimmer: Full range 0-100% Strobe eect:
1-5Hz Razor sharp beams
Energy-Saver: It has a mode that allows the operation with
half of the energy
Control
DMX Channels: 10 Operational modes: DMX, Master/Slave,
Auto-run & Sound- Active
Physical
4-digit LED display DMX connectors: 2 XLR connectors (XLR-
3 In and Out) Interlock power supply connector Dimensions:
352.5x231x298 mm. / 13.8x9x11.7 pulg. Weight: 10.9 Kg. / 24 Lbs.
1. Product Introduction:
1.1 Before unpack the xture, pls make
sure that the packing is in good condition,
following items will be found in the box:
• The xture
• This users guide
• 3m DMX cable
• 1.5m power cable with powercon
• Omega bracket for hanging installation
• Safety chain
1.2 Description of the Device
BOMBER
ENGLISH VERSION
p. 3
8. Mic
9. Mode/ESC button
10. Down button
11. Up button
12. Enter button
13. Fu se h o lder
1. Project lens
2. Head
3. Arm
4. Base
5. Display
6. Foot stand
7. O p e r a t i o n b u t t o n
14. P o w e r s w i t c h
15. Powercon in
16. 3-pin DMX in
17. 3-pin DMX out
18. Powercon out
Before operate this unit, please carefully read this users guide and keep if
needed in future. It’s necessary to respect following rules.
The disposal of the device aer lifecycle could damage the environment, need
to take it to special company for recycling or return to authorized dealer.
The products referred to in this manual conform to the European Community
Directives and are therefore marked with CE logo.
Keep this device away from children and unauthorized users, the manufac-
turer will not take responsibility for the damage due to any disregard of the
information provided in this manual and wrong operation.
Before operate the device, pls make sure the xture is in good housing, ensure
pan and tilt can rotate in its complete range.
Pls make sure minimal 0.5m distance need to kept between the xture to any
ammable material.
The device can only run with 100-240v voltage, 50/60Hz power, don’t connect
to any other wrong power. Disconnect the device from main power before
open the shield or maintenance.
--0.5m
2. Safety and maintenance Information
2.1 Safety Info
BOMBER
ENGLISH VERSION
p. 4
The device is designed only for indoor usage, pls keep it away from moisture.
Do not expose the device under the sun or directly to any other lighting source.
Never look directly into the projecting lens when the xture is power on, the
light may trigger epileptic seizures in photosensitive persons or persons with
epilepsy. Especially at beam eect, extreme caution and observance of these
safety instructions is mandatory.
Don’t put or install the device on a surface that subject to vibration or bumps.
Ta=45ºC The device is supposed to work in the temperate range -15° C and +45° C, do
not use the device when the temperate exceed this range.
The lens, shield need to be replaced when obviously broken, never use the
device when the shield is not completed closed.
Safety I class device, need to be earth connected.
When the xture is hanged overhead, the safety rope must be xed to the
bottom of the device to the appropriate xing point.
Always carry the device by the handles, do not take the head or arm directly
for transportation.
BOMBER
ENGLISH VERSION
p. 5
2.2 Maintenance
2.2.1 Operation only allowed to qualied person, damages
due to unprofessional operation or remove of any parts in-
side will not be considered in warranty service. There are no
serviceable parts inside the device or package, service only
leaves to authorized dealers.
2.2.3 Never allow the optical components contact with oil,
fat or any other liquid.
2.2.4 A regular clearance of the device is needed for long-
term usage, this is very helpful to maintain the lifetime and
brightness need to use a so and lint-free cloth to clean the
optical system, fan and air owing tunnel.
2.2.5. Trouble Shooting
Problems Possible reasons Checking or solutions
Device not power up Powercon or power cable damaged Change a good power cable to try
Faulty power supply Replace new power supply
Pan/Tilt error or vibrate
Faulty Pan/Tilt PCB Replace PT001 PCB
Faulty opto sensor Replace opto sensor OP001
Cable loosen Check the cable connect to OP001
LED o
Temperature protection Check the temperature from menu
Fan not working Check the fan speed info from menu
Faulty LED Replace new LED
Dimmer and strobe set at 0 Set dimmer and strobe channel at 255
Faulty power supply Replace new power supply
Device not response to
DMX
Faulty communication IC Replace the IC with back-up one in the display PCB
Faulty display PCB Replace new display PCB
Wrong DMX addressing Check the address and setting
Faulty DMX cable Change to a good DMX cable
2.2.6 Replacement of the fuse
Need to replace with same type and rating, which originally
installed in the device.
Step One: Unplug power cable from main power.
Step Two: Unscrew the fuse holder out of the housing with
a screwdriver.
Step Three: Remove the broken fuse and replace with an
exact same type of new fuse.
Step Four: Insert the fuse holder back to the housing and
screw tight and reconnect power.
BOMBER
ENGLISH VERSION
p. 6
3. Installation
3.3 How to do mounting installation.
Step one: Installation the clamp onto the omega bracket;
3.1 The device could be either put on a solid and even Sur-
face, or mounted upside down or sideways like le picture.
3.2 The mounting place must be suicient stable and be
able to support a weight of 10 times of the unit’s weight.
When the xture is hanged, always additionally secure the
device with the safety chain, fasten the safety rope at a
suitable position so that the maximum fall of the projector
will be 20 cm.
Step two: Install the clamp and bracket on the bottom of
panel, fasten the quick-locks;
Step three: Install the whole device onto appropriate truss
and fasten the clamps, tight the safety rope with the truss
or other xing point at a suitable position that drop down
distance not exceed 20 cm.
BOMBER
ENGLISH VERSION
p. 7
4. Control menu
Connect
DMX Addr XXX DMX address setting
Slave Rece Choose Slave mode
Sequence Alone/Master Choose Sequence mode
Music Alon/Master Choose Sound mode
Light Max Temp 80~130 ºC,85 ºC Lamp o if temperature continuously
over for 5 minutes
Lamp Adjust Pan=XXX….. Adjust value of each channels
Information Lamp Temp XXXC Temperature of driver
Set
Reset Reset
Movement
Pan Reve ON/OFF Pan Reverse
Tilt Reve ON/OFF Tilt Reverse
Pan Degree 630/540 Choose Pan Degree
Encoders ON/OFF Encoder wheel on/o
Move Mode Standard/Smooth Choose pan/tilt mode
UI Set
Mic Sens. 0~99%,60% Sensitivity of Mic
No Signal Close/Hold/Auto/Music Mode when no signal
Temper C/F Fahrenheit /Celsius Temperature at ºC/ºF
Fans Mode Auto /High Fans mode
Hibernation OFF, 01M~99M, 15M Sleeping mode
BackLight 02~60m 02m Show backlight time
Flip Display ON/OFF Display 180°reverse
Users Standard/Basic Users mode
Calibration
Password XXX Password: 050
Pan XXX Calibrate channel value
: :
Fixture ID
Name Name
-Password- Password: 050
PID Code Set PID of RDM
Soware V IC Version
Reload Def
Basic Reload
Reload Default
Password
All Reload
BOMBER
ENGLISH VERSION
p. 8
5. DMX connection and DMX protocol
5.1 DMX addressing:
5.1.1 The device is controlled by universal DMX 512 proto-
col, DMX address is the start channel used to receive instruc-
tions from the external controller. For independent control,
each xture must be assigned its unique address control
channels. For example, this device has four channel modes:
16/14, if we set the mode at standard 16 channels mode,
and there are several models need to be independently con-
trolled, we just simply address rst xture at 1, and second
xture at 16, third one at 32, etc.
If the devices have the same address, they will behave syn-
chronically.
DMX addressing is limited, don’t set the address so high that
without enough control channels for the xtures.
Display is ashing when no DMX signal is received.
5.1.4 Connection: us DMX cable with 3-pin XLR-plugs to con-
nect the controller with the xture or one xture with another.
BOMBER
ENGLISH VERSION
p. 9
5.2 DMX chart
Channel name function Min DMX Max DMX
St Ba1
1 1 Pan Pan Coarse 0 255
2 Pan ne Pan Fine 0 255
32 Tilt Tilt Coarse 0 255
4Tilt ne Tilt Fine 0 255
5 3 Movment Speed fastest to Slowest 0 255
64Movment Func-
tion
Normal 015
Movement With Backout 16 31
Pan Forward Spin 32 47
Pan Reverse Spin 48 63
Tilt Forward Spin 64 79
Tilt Reverse Spin 80 95
Pan&Tilt Forward Spin 96 111
Pan&Tilt Reverse Spin 112 127
Pan Forward Spin & Tilt Reverse Spin 128 143
Pan Reverse Spin & Tilt Forward Spin 144 159
TBD 160 255
75Shutter
Shutter closed 0 31
No function (shutter open) 32 63
Strobe eect slow to fast 64 95
No function (shutter open) 96 127
Pulse-eect in sequences 128 159
No function (shutter open) 160 191
Random strobe eect slow to fast 192 223
No function (shutter open) 224 255
8 6 Dimmer Dimmer(0->100%) 0 255
9 7 Virtual Color
Function
On Function 0 15
CTC Function 16 31
Forward Spin 32 47
Reverse Spin 48 63
Continuous 64 79
Color Bounce 80 111
TBD 112 255
BOMBER
ENGLISH VERSION
p. 10
Table des matières
Langues :
Autres manuels NEO Matériel de DJ
NEO
NEO Ion 280 3-en-1 Manuel utilisateur
NEO
NEO ION 132 F Manuel utilisateur
NEO
NEO NEO FLEX TRUSS Manuel utilisateur
NEO
NEO FOLLOWER 15R Manuel utilisateur
NEO
NEO FLEX STRIP Manuel utilisateur
NEO
NEO ION 610B RGBW Manuel utilisateur
NEO
NEO Blinder 64 Manuel utilisateur
NEO
NEO ELIPSOLED LITE 50 Manuel utilisateur
NEO
NEO NEO DOTZ Manuel utilisateur
NEO
NEO ELIPSOLED 5600 MAX Torch 4000 Manuel utilisateur
NEO
NEO ION 280F Manuel utilisateur
NEO
NEO ION 575 Manuel utilisateur
NEO
NEO Sion Manuel utilisateur
NEO
NEO NEO STRIP GOLD Manuel utilisateur
NEO
NEO FOLLOWER 400 LED Manuel utilisateur
NEO
NEO ION 715Z Manuel utilisateur
NEO
NEO PROTON IP 12 QA Manuel utilisateur
NEO
NEO ELIPSOLED 3100 MAX Manuel utilisateur
NEO
NEO STEAM INFINITE 450 Manuel utilisateur
NEO
NEO FRESNELED COLOR Manuel utilisateur
Manuels Matériel de DJ populaires d'autres marques
thomann
thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur
Eagletone
Eagletone 6 Eyes Flower Manuel utilisateur
EuroLite
EuroLite FLD-1508 Manuel utilisateur
Technical Pro
Technical Pro LG8xSEA Manuel utilisateur
JB Systems
JB Systems Lounge Laser DMX Manuel utilisateur
Lightmaxx
Lightmaxx Vega Halo 90 Manuel utilisateur
Elation
Elation FUZE WASH Z350 Manuel utilisateur
Maverick
Maverick MK3 WASH Manuel utilisateur
Infinity
Infinity TF-260C7 Fresnel Manuel utilisateur
Chauvet
Chauvet EVE E-50Z Manuel utilisateur
Eliminator Lighting
Eliminator Lighting E 138 Manuel utilisateur
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur