NEC NEC Express5800 Series Manuel utilisateur

SAP HANA Appliance

Express5800 A2040d

Initial Operation Verification Guide

of January 2017

NEC SAP Global Competence Center

2 © NEC Corporation 2017

. Preparation

. . Check the Power Plugs

Plea e check that all power plug are connected to the back of erver.

.2. Check the NICs

.2. . Production Network

Plea e check that all Network Interface Card are connected a required. Thi mean the two

dual port adapter mounted in lot number 9 and 16 hould be connected. The e 4 1GB port

are bonded by the OS driver. For your reference plea e ee the number on top of the PCI lot.

The below image doe not contain NIC in the e lot .

.2.2. Management Network

Plea e check that at lea t one of both management adapter (MGB1 Management and MGB2

Management) i connected to the network. With thi connection you can monitor your hardware

health.

.3. External Storage (JBOD)

Plea e connect the external torage to the 2

RAID controller.

The RAID controller i mounted in PCI lot 12. Plea e connect it port “A” to port “0” of the JBOD.

Plea e connect two power cable to the external torage a well.

3 © NEC Corporation 2017

2. Start the Server

2. . Power on the server

Pre ing the SYSTEM POWER Switch at the front of the erver turn on the erver.

Turn on the erver by u ing the following procedure.

Important

• Do not power on the server before amber SYSTEM POWER LED is unlit.

• Wait for at least 30 seconds before pressing the SYSTEM POWER switch on the server

after turning off the server.

1. Turn on the peripheral device and di play unit.

Note

If the power cord is connected to power control system such as an Uninterruptible Power Supply

(UPS), make sure that the power control system is turned on.

2. Remove Front Bezel, if mounted.

3. Pre the SYSTEM POWER witch at the front of the erver.

SYSTEM POWER LED i lit green and after a while, POST appear on the di play.

Important

Do not connect or disconnect USB device while POST is running. In addition, do not

connect or disconnect remote media.

Wait for the erver to fini h the boot operation. Once it ha completed you will be pre ented the

following login creen.

Plea e login to the OS.

4 © NEC Corporation 2017

2.2. Logon to the server

Depending on your in talled OS you will either be pre ented a graphical interface to login or a

CLI login prompt. In any ca e initial login credential are:

U ername : root

Pa word : hana

2.3. Start the SAP HANA Instance

1. Change u er to the < id>adm and tart HANA:

su - <sid>adm

HDB start

2. Check the SAP HANA In tance tatu , all hould be “GREEN”.

Plea e note that HANA tartup take ome time.

sapcontrol –nr <instance no> -function GetProcessList

3. Stop the Server

3. . Stop the SAP HANA Instance

1. Change u er to the < id>adm and top HANA:

su - <sid>adm

HDB stop

2. Check the SAP HANA In tance tatu , it mu t be “GRAY, Stopped”.

Plea e note that HANA hutdown take ome time.

sapcontrol –nr <instance no> -function GetProcessList

3.2. Power off the server

Power off the erver. U e the following command on terminal:

shutdown –h now

4. Additional information

For additional information about the hardware plea e review the “U er’ guide” for A2040d

available at www.58 upport.nec.co.jp/global/download

Autres manuels pour NEC Express5800 Series

107

Table des matières

Autres manuels NEC Serveur

NEC

NEC NEC Express5800 Series Manuel utilisateur

NEC

NEC EXPRESS 320Lb Manuel utilisateur

NEC

NEC NECCare Platinum Express5800/A1160 Manuel utilisateur

NEC

NEC NEC Express5800 Series Manuel utilisateur

NEC

NEC Univerge SV8100 R2 Guide d'installation

NEC

NEC Express5800/R320f Manuel utilisateur

NEC

NEC Univerge SV8100 Guide de l'utilisateur

NEC

NEC Express5800/320Lc Mode d’emploi

NEC

NEC Univerge SV8100 Manuel utilisateur

NEC

NEC NEC Express5800 Series Manuel utilisateur

NEC

NEC UNIVERGE NEAX 2000 IPS Manuel utilisateur

NEC

NEC Express5800/320Fa-L Manuel utilisateur

NEC

NEC EXPRESS800 Manuel utilisateur

NEC

NEC MH4500 Manuel utilisateur

NEC

NEC Express5800/320Lb FT Linux Mode d’emploi

NEC

NEC Express 5800 Manuel d'utilisation

NEC

NEC EXPRESS5800/120Md Series Manuel utilisateur

NEC

NEC Express5800/T71f Manuel utilisateur

NEC

NEC NECCare Platinum Express5800/A1160 Manuel utilisateur

NEC

NEC NEC Express5800 Series Manuel utilisateur

NEC

NEC Express5800/T110i Manuel utilisateur

NEC

NEC Express5800/B120e-h Manuel utilisateur

NEC

NEC Express5800/E120d-M Manuel utilisateur

NEC

NEC Express5800/320Fd-LR Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur