NEC GT5000 Series Manuel d'utilisation et d'entretien

Empowered by Innovation NEC

Basic Serial Control Codes

For NEC Projectors

Models:

GT5000/6000

MT860/1060/1065/1075

LT220/240/240K/260/260K

WT600

VT770

VT46/465/460/560/660/660K

HT1000/1100

Read First

The following pages include the ‘basic’ serial control codes for each model/series of NEC projectors.

Only the basic serial control codes are provided in this document.

NEC does not distribute the ‘full’ serial control code set.

NEC will supply more advanced control codes upon request.

Please contact the NEC rep you purchased the projector from for more advanced control codes. In your request, you

will need to give specific projector functions that you wish to control and only those codes will be supplied.

nec

For more information visit www.necvisualsystems.com

For Customer Service call (800) 836-0655

NEC is a registered trademark of NEC Corporation.

All other trademarks are the property of their respective owners.

All information is subject to change without notice.

NEC Solutions (Americia), Inc.

Visual Systems Division

1250 Arlington Heights Rd., Suite 400

Itasca,IL60143-1248 v1.1e

GT5000/6000

Control Codes

Function Code Data

POWER ON 02H 00H 00H 00H 00H 02H

POWER OFF 02H 01H 00H 00H 00H 03H

INPUT SELECT RGB 1 02H 03H 00H 00H 02H 01H 01H 09H

INPUT SELECT RGB 2 02H 03H 00H 00H 02H 01H 02H 0AH

INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH

INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H

INPUT SELECT DVI (DIGITAL) 02H 03H 00H 00H 02H 01H 1AH 22H

INPUT SELECT VIEWER 02H 03H 00H 00H 02H 01H 1FH 27H

LAN 02H 03H 00H 00H 02H 01H 20H 28H

SLOT 1-1 02H 03H 00H 00H 02H 01H 24H 2CH

SLOT 1-2 02H 03H 00H 00H 02H 01H 25H 2DH

SLOT 2-1 02H 03H 00H 00H 02H 01H 29H 31H

SLOT 2-2 02H 03H 00H 00H 02H 01H 2AH 32H

RGB1(VIDEO) 02H 03H 00H 00H 02H 01H 07H 0FH

RGB1(S-VIDEO) 02H 03H 00H 00H 02H 01H 0CH 14H

PICTURE MUTE ON 02H 10H 00H 00H 00H 12H

PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H

SOUND MUTE ON 02H 12H 00H 00H 00H 14H

SOUND MUTE OFF 02H 13H 00H 00H 00H 15H

ON SCREEN MUTE ON 02H 14H 00H 00H 00H 16H

ON SCREEN MUTE OFF 02H 15H 00H 00H 00H 17H

ASPECT RATIO 1.25:1 (5:4) 03H 10H 00H 00H 05H 18H 00H 00H 00H 00H 30H

1.33:1 (4:3) 03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H

1.78:1 (16:9) 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H

1.85:1 03H 10H 00H 00H 05H 18H 00H 00H 03H 00H 33H

2.35:1 03H 10H 00H 00H 05H 18H 00H 00H 04H 00H 34H

AUTO ADJUST 02H 0FH 00H 00H 02H 05H 00H 18H

Note: Contact your NEC rep for codes not listed.

Cable Connection

Communication Protocol: PC Control Connector (D-Sub 9P)

Baud Rate: 38400 bps

12345

67 89

To GND of PC

To RxD of PC

To TxD of PC

To CTS of PC

To RTS of PC

Data Length: 8 bits

Parity: No Parity

Stop Bit: One bit

X on/off: None

Communications: Full duplex

NOTE1: It is recommended to set the projector to “Idle Mode” in the Setup menu for best Power ON response.

NOTE2: Pins 1, 4, 6, and 9 are used inside the projector.

NOTE3: Jumper “Request to send” and “Clear to Send” together on both ends of the cable to simplify cable connection.

NOTE4: For long cable runs it is recommended to set communication speed to 9600 bps in the Setup menu.

MT860/1060/1065/1075

Control Codes

Function Code Data

POWER ON 02H 00H 00H 00H 00H 02H

POWER OFF 02H 01H 00H 00H 00H 03H

INPUT SELECT RGB 1 02H 03H 00H 00H 02H 01H 01H 09H

INPUT SELECT RGB 2 02H 03H 00H 00H 02H 01H 02H 0AH

INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH

INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H

INPUT SELECT DVI (DIGITAL) 02H 03H 00H 00H 02H 01H 1AH 22H

INPUT SELECT VIEWER 02H 03H 00H 00H 02H 01H 1FH 27H

PICTURE MUTE ON 02H 10H 00H 00H 00H 12H

PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H

SOUND MUTE ON 02H 12H 00H 00H 00H 14H

SOUND MUTE OFF 02H 13H 00H 00H 00H 15H

ON SCREEN MUTE ON 02H 14H 00H 00H 00H 16H

ON SCREEN MUTE OFF 02H 15H 00H 00H 00H 17H

ASPECT RATIO (4:3 Screen) 4:3 03H 10H 00H 00H 05H 18H 00H 00H 00H 00H 30H

Letterbox 03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H

Widescreen 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H

Crop 03H 10H 00H 00H 05H 18H 00H 00H 03H 00H 33H

ASPECT RATIO (16:9 Screen) 4:3 Window 03H 10H 00H 00H 05H 18H 00H 00H 00H 00H 30H

Letterbox 03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H

Widescreen 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H

4:3 Fill 03H 10H 00H 00H 05H 18H 00H 00H 04H 00H 34H

AUTO ADJUST 02H 0FH 00H 00H 02H DDH 00H F0H

NOTE:Contact your NEC rep for codes not listed.

Cable Connection

Communication Protocol: PC Control Connector (D-Sub 9P)

Baud Rate: 38400 bps

12345

6789

To GND of PC

To RxD of PC

To TxD of PC

To CTS of PC

To RTS of PC

Data Length: 8 bits

Parity: No Parity

Stop Bit: One bit

X on/off: None

Communications: Full duplex

NOTE 1: It is recommended to set the projector to “Idle Mode” in the Setup menu for best Power ON response.

NOTE 2: Pins 1, 4, 6, and 9 are used inside the projector.

NOTE 3: Jumper “Request to send” and “Clear to Send” together on both ends of the cable to simplify cable connection.

NOTE 4: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps.

LT220/240/240K/260/260K

Control Codes

Function Code Data

POWER ON 02H 00H 00H 00H 00H 02H

POWER OFF 02H 01H 00H 00H 00H 03H

INPUT SELECT RGB 1 02H 03H 00H 00H 02H 01H 01H 09H

INPUT SELECT RGB 2 02H 03H 00H 00H 02H 01H 02H 0AH

INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH

INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H

INPUT SELECT VIEWER 02H 03H 00H 00H 02H 01H 1FH 27H

PICTURE MUTE ON 02H 10H 00H 00H 00H 12H

PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H

SOUND MUTE ON 02H 12H 00H 00H 00H 14H

SOUND MUTE OFF 02H 13H 00H 00H 00H 15H

ON SCREEN MUTE ON 02H 14H 00H 00H 00H 16H

ON SCREEN MUTE OFF 02H 15H 00H 00H 00H 17H

ASPECT RATIO (4:3 Screen) 4:3 03H 10H 00H 00H 05H 18H 00H 00H 00H 00H 30H

Letterbox 03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H

Widescreen 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H

Crop 03H 10H 00H 00H 05H 18H 00H 00H 03H 00H 33H

ASPECT RATIO (16:9 Screen) 4:3 Window 03H 10H 00H 00H 05H 18H 00H 00H 00H 00H 30H

Letterbox 03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H

Widescreen 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H

4:3 Fill 03H 10H 00H 00H 05H 18H 00H 00H 04H 00H 34H

AUTO ADJUST 02H 0FH 00H 00H 02H 05H 00H 18H

NOTE:Contact your NEC rep for codes not listed.

Cable Connection

Communication Protocol PC Control Connector (DIN-8P)

Baud Rate: 38400 bps

Data Length: 8 bits

To RxD of PC

345

678

To TxD of PCTo GND of PC

Parity: No Parity

Stop Bit: One bit

X on/off: None

Communications: Full duplex

NOTE 1: It is recommended to set the projector to “Idle Mode” in the Setup menu for best Power ON response.

NOTE 2: Pins 2, 3, 5, 6 and 8 are used inside the projector.

NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps.

WT600

Control Codes

Function Code Data

POWER ON 02H 00H 00H 00H 00H 02H

POWER OFF 02H 01H 00H 00H 00H 03H

INPUT SELECT RGB 02H 03H 00H 00H 02H 01H 01H 09H

INPUT SELECT DVI (ANALOG) 02H 03H 00H 00H 02H 01H 02H 0AH

INPUT SELECT DVI (DIGITAL) 02H 03H 00H 00H 02H 01H 1AH 22H

INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH

INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H

INPUT SELECT VIEWER 02H 03H 00H 00H 02H 01H 1FH 27H

PICTURE MUTE ON 02H 10H 00H 00H 00H 12H

PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H

SOUND MUTE ON 02H 12H 00H 00H 00H 14H

SOUND MUTE OFF 02H 13H 00H 00H 00H 15H

ON SCREEN MUTE ON 02H 14H 00H 00H 00H 16H

ON SCREEN MUTE OFF 02H 15H 00H 00H 00H 17H

ASPECT RATIO (4:3 Screen) 4:3 03H 10H 00H 00H 05H 18H 00H 00H 00H 00H 30H

Letterbox 03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H

Widescreen 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H

Crop 03H 10H 00H 00H 05H 18H 00H 00H 03H 00H 33H

ASPECT RATIO (16:9 Screen) 4:3 Window 03H 10H 00H 00H 05H 18H 00H 00H 00H 00H 30H

Letterbox 03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H

Widescreen 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H

4:3 Fill 03H 10H 00H 00H 05H 18H 00H 00H 04H 00H 34H

AUTO ADJUST 02H 0FH 00H 00H 02H 05H 00H 18H

Note: Contact your NEC rep for codes not listed.

Cable Connection

Communication Protocol: PC Control Connector (DIN-8P)

Baud Rate: 38400 bps

Data Length: 8 bits

To RxD of PC

345

678

To TxD of PC

To GND of PC

Parity: No Parity

Stop Bit: One bit

X on/off: None

Communications: Full duplex

NOTE 1: It is recommended to set the projector to “Idle Mode” in the Setup menu for best Power ON response.

NOTE 2: Pins 2, 3, 5, 6 and 8 are used inside the projector.

NOTE 3: For long cable runs it is recommended to set communication speed in the Setup menu to 9600 bps.

VT770

Control Codes

Function Code Data

POWER ON 02H 00H 00H 00H 00H 02H

POWER OFF 02H 01H 00H 00H 00H 03H

INPUT SELECT COMPUTER 1 02H 03H 00H 00H 02H 01H 01H 09H

INPUT SELECT COMPUTER 2 02H 03H 00H 00H 02H 01H 02H 0AH

INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH

INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H

INPUT SELECT COMPONENT 02H 03H 00H 00H 02H 01H 1AH 22H

INPUT SELECT VIEWER 02H 03H 00H 00H 02H 01H 1FH 27H

PICTURE MUTE ON 02H 10H 00H 00H 00H 12H

PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H

SOUND MUTE ON 02H 12H 00H 00H 00H 14H

SOUND MUTE OFF 02H 13H 00H 00H 00H 15H

ON SCREEN MUTE ON 02H 14H 00H 00H 00H 16H

ON SCREEN MUTE OFF 02H 15H 00H 00H 00H 17H

ASPECT RATIO (4:3 Screen) 4:3 03H 10H 00H 00H 05H 18H 00H 00H 00H 00H 30H

Letterbox 03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H

Widescreen 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H

Crop 03H 10H 00H 00H 05H 18H 00H 00H 03H 00H 33H

ASPECT RATIO (16:9 Screen) 4:3 Window 03H 10H 00H 00H 05H 18H 00H 00H 00H 00H 30H

Letterbox 03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H

Widescreen 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H

4:3 Fill 03H 10H 00H 00H 05H 18H 00H 00H 04H 00H 34H

AUTO ADJUST 02H 0FH 00H 00H 02H 05H 00H 18H

Note: Contact your NEC rep for codes not listed.

Cable Connection

Communication Protocol: PC Control Connector (D-Sub 9p)

Baud Rate: 38400 bps

Data Length: 8 bits

12345

67 89

To GND of PC

To RxD of PC

To TxD of PC

To CTS of PC

To RTS of PC

Parity: No Parity

Stop Bit: One bit

X on/off: None

Communications: Full duplex

NOTE1: It is recommended to set the projector to “Idle Mode” in the Setup menu for best Power ON response.

NOTE2: Pins 1, 4, 6, and 9 are used inside the projector.

NOTE3: Jumper “Request to send” and “Clear to Send” together on both ends of the cable to simplify cable connection.

NOTE4: For long cable runs it is recommended to set communication speed to 9600 bps in the Setup menu.

VT46/465/460/560/660/660K

Control Codes

Function Code Data

POWER ON 02H 00H 00H 00H 00H 02H

POWER OFF 02H 01H 00H 00H 00H 03H

INPUT SELECT RGB 02H 03H 00H 00H 02H 01H 01H 09H

INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH

INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H

PICTURE MUTE ON 02H 10H 00H 00H 00H 12H

PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H

SOUND MUTE ON 02H 12H 00H 00H 00H 14H

SOUND MUTE OFF 02H 13H 00H 00H 00H 15H

NOTE:Contact your NEC rep for codes not listed.

Cable Connection

Communication Protocol PC Control Connector (DIN-8P)

Baud Rate: 19200 bps

Data Length: 8 bits

To RxD of PC

345

678

To TxD of PC

To GND of PC

Parity: No Parity

Stop Bit: One bit

X on/off: None

Communications: Full duplex

NOTE 1: Pins 2, 3, 5, 6 and 8 are used inside the projector.

NOTE 2: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps.

HT1000/1100

Control Codes

FUNCTION CODE DATA

POWER ON 02H 00H 00H 00H 00H 02H

POWER OFF 02H 01H 00H 00H 00H 03H

INPUT SELECT RGB 02H 03H 00H 00H 02H 01H 01H 09H

INPUT SELECT COMPONENT 02H 03H 00H 00H 02H 01H 10H 18H

INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH

INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H

INPUT SELECT DVI (DIGITAL) 02H 03H 00H 00H 02H 01H 1AH 22H

INPUT SELECT VIEWER 02H 03H 00H 00H 02H 01H 1FH 27H

PICTURE MUTE ON 02H 10H 00H 00H 00H 12H

PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H

SOUND MUTE ON 02H 12H 00H 00H 00H 14H

SOUND MUTE OFF 02H 13H 00H 00H 00H 15H

ON SCREEN MUTE ON 02H 14H 00H 00H 00H 16H

ON SCREEN MUTE OFF 02H 15H 00H 00H 00H 17H

ASPECT RATIO (16:9 Screen) NORMAL 03H 10H 00H 00H 05H 18H 00H 00H 05H 00H 35H

FULL 03H 10H 00H 00H 05H 18H 00H 00H 06H 00H 36H

ZOOM 03H 10H 00H 00H 05H 18H 00H 00H 07H 00H 37H

STADIUM 03H 10H 00H 00H 05H 18H 00H 00H 0AH 00H 3AH

ASPECT RATIO (4:3 Screen) NORMAL 03H 10H 00H 00H 05H 18H 00H 00H 05H 00H 35H

ZOOM 03H 10H 00H 00H 05H 18H 00H 00H 07H 00H 37H

CINEMA 03H 10H 00H 00H 05H 18H 00H 00H 08H 00H 38H

V-ZOOM 03H 10H 00H 00H 05H 18H 00H 00H 09H 00H 39H

AUTO ADJUST 02H 0FH 00H 00H 02H 05H 00H 18H

Note: Contact your NEC rep for codes not listed.

Cable Connection

Communication Protocol: PC Control Connector (DIN-8P)

Baud Rate: 38400 bps

Data Length: 8 bits

786

To RxD of PC

To TxD of PC

To GND of PC

Parity: No Parity

Stop Bit: One bit

X on/off: None

Communications: Full duplex

NOTE 1: It is recommended to set the projector to “Idle Mode” in the Setup menu for best Power ON response.

NOTE 2: Pins 2, 3, 5, 6 and 8 are used inside the projector.

NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps.

Autres manuels pour GT5000 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels NEC Projecteur

NEC

NEC DLP CINEMA NC1600C Manuel utilisateur

NEC

NEC NP200 - XGA DLP Projector Manuel utilisateur

NEC

NEC GT5000 Series Manuel utilisateur

NEC

NEC M402H Manuel utilisateur

NEC

NEC LT75Z - MultiSync SVGA DLP Projector Manuel utilisateur

NEC

NEC TriDigital HD10K Manuel utilisateur

NEC

NEC PA653U Manuel utilisateur

NEC

NEC VT37 Manuel utilisateur

NEC

NEC PA803UL Manuel utilisateur

NEC

NEC PA622U Manuel utilisateur

NEC

NEC PA1705UL-W Manuel utilisateur

NEC

NEC P501XG Manuel

NEC

NEC LT180 - LT 180 XGA DLP Projector Manuel utilisateur

NEC

NEC NP2150 Series Instructions d'installation et d'entretien

NEC

NEC M282X Manuel utilisateur

NEC

NEC VT800 Series Manuel utilisateur

NEC

NEC P627UL Manuel utilisateur

NEC

NEC LT100 - MultiSync XGA DLP Projector Guide d'installation et d'utilisation

NEC

NEC P452W Manuel utilisateur

NEC

NEC LCDMT850 Guide d'installation et d'utilisation

NEC

NEC MultiSync GT2000 Manuel utilisateur

NEC

NEC VT48 Series Manuel utilisateur

NEC

NEC NP64 Series Guide de configuration

NEC

NEC NC1201L-A Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur