NEC X554UN-TMX4P Manuel utilisateur
NEC Display Solutions of America, Inc.
QIG-TMX4P-554UNS
X554UN-TMX4P, X554UNS-TMX4P Rev 1.1
Parts List
o(4) X554UN or X554UNS Displays
o(4) Onsite Service Warranties (ONSITEMN-3Y-16 or ONSITEMN-3Y-17)
o(4) Peerless Pullout Wall Mounts (DS-VW765-L40)
o(1) 25ft Cat5e Patch Cable
o(4) 3m DisplayPort 1.2 Cables
o(1) IR/Remote Control Kit (KT-RC2)
o(2) Overframe Bezel Kits (KT-55UN-OF or KT-55UN-OF2)
o(2) Tripp Lite 6 Outlet Strip (ISOBar6)
o(1) Display Wall Calibrator Kit (KT-LFD-CC)
NOTES:
oAny walls that this video wall solution is anchored to must be strong enough to support the displays and the
installation must be in accordance with any local building codes. All mounting apparatuses must make secure
contact to wooden studs.
oPlease read entire document before starting installation
NEC Display Solutions of America, Inc.
QIG-TMX4P-554UNS
X554UN-TMX4P, X554UNS-TMX4P Rev 1.1
2
1. For mounting information, please refer to Installation Instructions provided by Peerless
Industries, Inc. inside the box of the DS-VW765-L40.
2. Connect the NEC display using the provided DisplayPort cables. Please note that in the
picture below, the IN connection is on the left and circled in red while the OUT connection is
on the right and circled in blue.
3. Connect the LAN cables that are located within the display box to daisy chain each display.
Note that the 25ft cat5e patch cable provided is optional and can be used for connecting the
source to display 1 within the wall. Note that in the picture below, LAN1 is on the left and
circled in red while LAN2 is on the right and circled in blue. LAN1 should be utilized as the
IN connection and LAN2 should be utilized as the OUT connection The LAN daisy chain
can be utilized to pass RS232C, IR Remote or TCP/IP information to each display down the
daisy chain.
4. Apply the OverFrame bezel kit to the video wall. Please follow instructions provided with kit.
KT-46UN-OF is utilized with the X554UN displays and KT-46UN-OF2 is utilized with the
X554UNS displays
Overframe Kit
NEC Display Solutions of America, Inc.
QIG-TMX4P-554UNS
X554UN-TMX4P, X554UNS-TMX4P Rev 1.1
3
5. Screw the IR Receiver (KT-RC2) directly to the outside of the video wall and plug it directly
into the IR In terminal of Display 1 as shown below.
6. Power up all of the displays and make sure that the LAN power is on for each display. This
can be found in the External Control menu.
Note that LAN power is OFF out of the box so this will need to be changed for each display
within the wall.
7. Go into the Multi-DSP menu of the display 1 which will be where you first started the LAN
daisy chain and enable the AUTO ID within the ID Control setting. This will automatically
set a monitor ID to each display along the LAN daisy chain. Note that the displays will
automatically identify each screen consecutively depending on how you LAN daisy chained
the units.
NEC Display Solutions of America, Inc.
QIG-TMX4P-554UNS
X554UN-TMX4P, X554UNS-TMX4P Rev 1.1
4
If the control setup is as pictured below, each display does not need a unique IP address
assigned to still control each individual monitor.
Note that a unique IP address is not necessary to communicate to all displays if display 1 is
not connected to a network. The displays will automatically assign themselves IP
addresses if no DNS is detected and the IP Setting within the IP Address Setting in the
External Control menu is set to AUTO. Note that this is the setting out of the box.
NEC Display Solutions of America, Inc.
QIG-TMX4P-554UNS
X554UN-TMX4P, X554UNS-TMX4P Rev 1.1
5
8. If display 1 is connected to a network or LAN is going into display 1, like the picture below,
each display will need a unique IP address to ensure that communication can successfully
go through the daisy chain from screen to screen.
9. Ensure that video source is connected to the DisplayPort In interface of display 1. Make
sure that all displays are on the DisplayPort input. Note that the DisplayPort out on each
display can be used to output the DVI, HDMI, OPTION or DisplayPort signals that are
coming in to that specific display, however, when the next step is completed the display will
automatically switch each display to the DisplayPort input. If the source is inputted into
display 1 via HDMI, DVI or the OPTION input, it will manually have to be changed. If a
NEC Display Solutions of America, Inc.
QIG-TMX4P-554UNS
X554UN-TMX4P, X554UNS-TMX4P Rev 1.1
6
source is connected into display 1 and everything is daisy chained properly, each display
should be showing the same image.
10. Go into the Multi-DSP menu to activate Auto Tile Matrix Setup as seen in the picture below.
Note that you will need to set the horizontal and vertical monitor dimensions before you
activate the Auto Tile Matrix. If done correctly and the LAN is daisy chained as shown on
the picture on the previous screen, the displays will automatically adjust so one large picture
fills the entirety of the wall. Activating Auto Tile Matrix changes the Tile Matrix, Tile Matrix
Mem, Input Signal, Video Out Setting and DisplayPort in the Terminal Settings menu.
Note that there is a limitation if High-bandwidth Digital Content Protection (HDCP) is
utilized. If inputting HDCP content through the HDMI, DVI or OPTION terminal the
content will NOT daisy chain to the consecutive displays. If inputting through the
DisplayPort terminal then the limitation of distributing video to consecutively daisy
chained displays is a total of 3 units. NEC Display Solutions recommends that an
HDCP compliant distribution amplifier is utilized for all HDCP applications.
If you are experiencing issues with this setup, please call our Technical Support number at
(800) 632-4662
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels NEC Moniteur
NEC
NEC MultiSync X461S Manuel utilisateur
NEC
NEC FP1350 - MultiSync - 22" CRT Display Manuel utilisateur
NEC
NEC PowerMate eco Guide de configuration
NEC
NEC 90GX2 - MultiSync - 19" LCD Monitor Manuel utilisateur
NEC
NEC 1500M LA-1524HMW Manuel utilisateur
NEC
NEC LCD1555V Manuel utilisateur
NEC
NEC X463UN-TMX4P Supplément
NEC
NEC PlasmaSync PX-42M2A Manuel utilisateur
NEC
NEC LCD3215 - MultiSync - 32" LCD Flat Panel... Manuel utilisateur
NEC
NEC MultiSync V323-3 Manuel utilisateur
NEC
NEC MDview Series Manuel utilisateur
NEC
NEC NRP-60LCD1 Manuel utilisateur
NEC
NEC NEC MultiSync FE1250 FE1250 FE1250 Manuel utilisateur
NEC
NEC MultiSync UN552S-TMX9P Manuel utilisateur
NEC
NEC MultiSync LCD3090WQXi Manuel utilisateur
NEC
NEC MultiSync MD301C4 Manuel utilisateur
NEC
NEC AccuSync LCD71VM Manuel utilisateur
NEC
NEC 42/50PD1 Manuel utilisateur
NEC
NEC AccuSync 120 Manuel utilisateur
NEC
NEC MultiSync LCD1800 Manuel utilisateur
