NEC X463UN-TMX4P Supplément

NEC Display Solutions of America, Inc.

QIG-TMXP-46UN

X463UN-TMX4P Rev 1.0

Parts List

o(4) X463UN Displays

o(4) Overnight Onsite Service Warranties (OnSiteOn-46)

o(4) Peerless Pullout Wall Mount (DS-VW765-LAND)

o(2) Peerless Video Wall Spacers (DW-VWS013)

o(4) 2m DVI-D to DVI-D M/M cables

o(1) 5m DVI-D to DVI-D M/M cable

o(3) 10ft Null Modem to Null Modem F/F cables

o(1) IR/Remote Control Kit (KT-RC)

o(2) Overframe Bezel Kits (KT-46UN-OF2)

o(2) Tripp Lite 6 Outlet Strip (ISOBar6)

NOTES:

oAny walls that this video wall solution is anchored to must be strong enough to support the displays and the

installation must be in accordance with any local building codes. All mounting apparatuses must make secure

contact to wooden studs.

oPlease read entire document before starting installation

NEC Display Solutions of America, Inc.

QIG-TMXP-46UN

X463UN-TMX4P Rev 1.0

1. For mounting information, please refer to the Installation Instructions provided by Peerless

AV inside of the boxes of the DS-VW765-LAND mount units.

2. Connect the NEC displays using the included DVI cables and the integrated DVI

loopthrough connections on the bottom of each monitor. Note that the DVI connection

closest to the front of the display is the ‘in’ connection while the connection closest to the

wall is the ‘out’ connection.

The cabling set up below is only one way of completing this. DVI daisy chaining can be

done a number of different ways and still yield the same results. Note that the connections

for each X463UN monitor are on the bottom of each display, not the side as shown in the

image below. It may be helpful to start wiring before mounting.

3. Connect the null modem cabling to each display. This should follow a chain that is easy to

remember, like 1-2-3-4 or 1-2-4-3. Note that the null modem cable needed to run from the

source computer to Display 1 is not included in this bundle. This will need to be purchased

separately to control the display remotely over RS232. Looping through the provided IR

cables is optional at this point.

NEC Display Solutions of America, Inc.

QIG-TMXP-46UN

X463UN-TMX4P Rev 1.0

4. Apply the OverFrame bezel kit to the video wall. Please follow instructions provided with kit

(KT-55UN-OF).

5. Screw the IR Receiver (KT-RC) directly to the outside of the video wall and plug it directly

into the IR In terminal of Display 1.

6. Set each monitor ID up individually through the ‘MULTI-DSP’ menu within the OSD. It’s

recommended that the ID’s go from left to right, with the ID No. 1 being in the top left corner.

Overframe Kit

IR In

RS232 In

RS232 Out

IR Out

NEC Display Solutions of America, Inc.

QIG-TMXP-46UN

X463UN-TMX4P Rev 1.0

Note that after the ID’s are set, there are two different ways to communicate to each screen

via the IR Remote. If the setting for the ‘IR Control’ within the ‘MULTI-DSP’ menu is set to

‘Normal’, then the IR remote control cabling is being utilized for communication. In order to

communicate to each screen individually, hold down the ‘Remote ID Set’ button on the

remote control, tap the number of the ID that you want to communicate with, then release

the Remote ID Set button. To test if this was done correctly, press the MENU button and

the OSD should now only appear on the display in which the remote control is

corresponding to. Also, more information on this is located within the User’s Manual.

To communicate to each display over the RS232 connection, make sure that the first display

(monitor ID 1) has its IR control set to ‘Primary’, while all others are set to ‘Secondary’. One

way to accomplish this easily is to set the second display in the RS232 daisy chain to

secondary, then utilize the copy function to the remaining displays in the wall. When this is

complete, the ‘Auto ID’ function can be utilized to set the ID’s for every screen in the wall.

When all is set, press the ‘Display’ button and the Monitor ID and Target ID should come up

in the left corner of each screen. Use the [+] and [-] buttons on the remote to change the

Target ID to the desired display you wish to communicate with then press ‘Display’ again. If

the menu is then pressed, the OSD menu should appear on the screen of the desired ID.

NEC Display Solutions of America, Inc.

QIG-TMXP-46UN

X463UN-TMX4P Rev 1.0

7. Use the TileMatrix feature to setup the 2x2 Video Wall. The Tilematrix feature of the NEC

Display allows for one image to be expanded and displayed over a 2x2 Video Wall Setup.*

This is accessed through the OSD (On-Screen Display) Controls under the “MULTI-DSP”

main menu icon. Under the TileMatrix sub-menu, enable the feature and set the necessary

parameters that match the 2x2 Video Wall setup. Note that this step will need to be

completed for each screen.

8. Select if TileComp is necessary for this application or not. TileComp works in tandem with

TileMatrix to compensate for the width of the tiled bezels in order to accurately display the

image. Click ‘YES’ on enable to display video wall. Note that this step will need to be

completed for each screen.

If you are experiencing issues with this setup, please call our Technical Support number at

(800) 632-4622

Table des matières

Autres manuels NEC Moniteur

NEC

NEC NEC MultiSync LCD1525V LCD1525V LCD1525V Manuel utilisateur

NEC

NEC EA243WM-BK Manuel utilisateur

NEC

NEC E556 Manuel utilisateur

NEC

NEC MultiSync LCD1735NXM Manuel utilisateur

NEC

NEC PX-50XM4 Manuel utilisateur

NEC

NEC EA273WM-BK Manuel utilisateur

NEC

NEC LCD1525M - MultiSync - 15" LCD Monitor Manuel utilisateur

NEC

NEC MultiSync V920 Manuel utilisateur

NEC

NEC MultiSync P554 Manuel utilisateur

NEC

NEC LC15m Manuel utilisateur

NEC

NEC AS241W-BK Manuel utilisateur

NEC

NEC MultiSync FE700+ Manuel utilisateur

NEC

NEC LCD1980SX - MultiSync - 19" LCD Monitor Guide de l'utilisateur

NEC

NEC MultiSync V463 Manuel utilisateur

NEC

NEC MultiSync LCD1515 Mode d’emploi

NEC

NEC MultiSync UN462A Manuel d'utilisation et d'entretien

NEC

NEC MultiSync LCD1525X Manuel utilisateur

NEC

NEC MultiSync EA221WM Manuel utilisateur

NEC

NEC MultiSync LCD1515 Manuel utilisateur

NEC

NEC MultiSync V422 Mode d’emploi

NEC

NEC MD211G3 Manuel utilisateur

NEC

NEC MultiSync LCD2000 Manuel utilisateur

NEC

NEC MultiSync X551UN Manuel utilisateur

NEC

NEC PlasmaSync 42XM4 Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation

LG M1950D-PZ Manuel utilisateur