National Instruments FieldPoint FP-1000 Manuel utilisateur

FP-1000/1001 FieldPoint Quick Start Guide

Install the Network Module

Panel MountDIN Rail Mount

A. Unlock rail clip.

Network Module

Mounting Hardware (DIN rail

or panel mount accessory)

Terminal Base(s)

·I/O Module(s)

·Power Supply

·Accessories: serial cable,

screwdriver

·PC running Windows

·FieldPoint Software CD

What You Need to Get Set Up

You can mount the modules on a DIN rail or to a panel.

fpoint 1000-1001 cd.qxd 1/4/02 4:26 PM Page 1

B. Hook lip on back of module onto top

of DIN rail, press down, and snap

into place.

B. Snap panel mount accessory

(which you can order separately)

onto module.

Panel MountDIN Rail Mount

NOTE: Do not use spliced DIN

rails. Use only a single DIN rail.

C. Slide module into position and lock

rail clip.

C. Lock rail clip.

D. Use template that came with the

accessory to drill pilot holes and

mount module onto

panel using

accessory.

fpoint 1000-1001 cd.qxd 1/4/02 4:26 PM Page 2

Install the Terminal Base(s)

CAUTION: Terminal bases must be connected to the network module

before applying power to the module. Do

not

connect or disconnect

terminal bases while power is applied to the network module.

DIN Rail Mount

A. Unlock rail clip.

B. Press base onto rail.

Panel Mount

A. Use template that came with the

accessory to drill pilot holes.

B. Connect terminal base to network

module connector, being careful not

to bend any connector pins.

C. Fasten terminal base to panel.

fpoint 1000-1001 cd.qxd 1/4/02 4:26 PM Page 3

DIN Rail Mount Panel Mount

D. Repeat for each terminal base, up

to nine for each network module in

most cases. You can use one or

two extender cables (which you can

order separately) if the FieldPoint

bank is too long for the available

space.

E. Place protective cover on last base,

and install rail locks at each end.

C. Slide into position and lock the rail

clip. Be careful not to bend any pins. D. Repeat for each terminal base, up to

nine for each network module in

most cases. You can use one or two

extender cables (which you can order

separately) if the FieldPoint bank is

too long for the available space.

E. Place protective cover on last base.

fpoint 1000-1001 cd.qxd 1/4/02 4:26 PM Page 4

Install the I/O Module(s)

A. Align slots on module with guide rails on

base, and press onto base until terminal

base’s latch locks the module in place.

B. Repeat for each I/O module.

It does not matter where you install each I/O module, except for

these types of situations:

··

·· If you plan to cascade power between any I/O modules using the

V and C terminals, those modules should be grouped together.

··

·· For more accurate measurements, you might want to locate any

thermocouple modules away from heat sources, including network

modules or relay modules, unless you are mounting them on an FP-TB-3.

fpoint 1000-1001 cd.qxd 1/4/02 4:26 PM Page 5

Connect the Network Cables

You have several network connection options with the FP-1000 and FP-1001,

as shown here.

Connecting the FP-1000 to a Computer’s RS-232 Serial Port

Use a male-to-female (straight through) cable to connect the computer’s RS-

232 port to the 9-position DSub RS-232 connector on the FP-1000.

FP-1000

NOTE: You cannot connect the RS-485 port of the FP-1000 directly to an

RS-485 port on the computer.

If you are using multiple FieldPoint serial network modules, you may need to

connect the grounds of the RS-485 communication ports to each other to

prevent damage from differences in ground potentials.

fpoint 1000-1001 cd.qxd 1/4/02 4:26 PM Page 6

Connecting the FP-1000 to an FP-1001

1 From the Computer’s RS-232 Transmit Output

2 To Host Computer’s RS-232 Receive Input

3 Ground

4 120 Termination Resistors

You can connect up to 24 FP-1001 RS-485 serial network modules to an

FP-1000. Use the RS-485 repeater port of the FP-1000, with the connection shown

in this figure.

A. Connect the TX outputs of the FP-1001

to the RX inputs of the FP-1000, and

the RX inputs of the FP-1001 to the TX

outputs of the FP-1000.

B. Install the termination resistors.

Terminate each end of your RS-485

network using the 120 termination

resistors included with the FP-1001.

Install them between the RX and TX

pair of the FP-1000’s RS-485 port,

and between the RX and TX pair on the

last FP-1001’s RS-485 port, as shown.

Twist the resistor leads with the RS-485

signal wires and insert them into the

RS-485 port terminals.

FP-1001

TX+

TX-

GND

RX+

RX-

FP-1001

TX+

TX-

GND

RX+

RX-

FP-1000

TX+

TX-

GND

RX+

RX-

fpoint 1000-1001 cd.qxd 1/4/02 4:26 PM Page 7

Connecting the FP-1001 to a Computer’s RS-485 Serial Port

You may connect up to 25 FP-1001 network modules to a single RS-485 port of a

host computer. Use the connection shown in this figure.

A. Connect the FP-1001 to a host computer

using the 5-position Combicon screw

terminal adapter of the RS-485 connector

on the FP-1001.

B. Install the 120 termination resistors

included with the FP-1001. Install them

between the RX and TX pair of the host

computer’s RS-485 port, and between

the RX and TX pair on the RS-485

port of the last FP-1001 in the system,

as shown. Twist the resistor leads with

the RS-485 signal wires and insert

them into the RS-485 port terminals.

C. Check the biasing feature. The host

computer's RS-485 interface usually

provides for biasing resistors,

which are required on an

RS-485 network. You should

use this biasing feature for better

reliability and noise immunity.

FP-1001

TX+

TX-

GND

RX+

RX-

FP-1001

TX+

TX-

GND

RX+

RX-

Computer’s

RS-485 Port

120

Resistors

NOTE: The pinout for the RS-485 DB-9

connector shown is for National Instruments

RS-485 cards. Please refer to the manuals

that came with your RS-485 card, as the

pinout may vary by manufacturer.

120

Resistors

fpoint 1000-1001 cd.qxd 1/4/02 4:26 PM Page 8

Set the Network Address and Baud Rate

If the default values do not work for you, remove the switch cover from the

8-position switch on the front of the FP-1000/1001 to set the network

address and baud rate.

123 4 5678

1234 5678

Address

Baud

Rate

Address 0 Address 1 Address 2

Default address 0 shown

Default Baud Rate 115200 shown

A. Check/Set the Network Address

Give every network module connected to one serial port of the host computer a

unique address, but modules on different serial ports may have the same address.

The addresses of the terminal bases connected to the network module are

automatically configured to be sequentially higher than the network module’s

address, moving out from the network module. The default network address

for the FP-1000/1001 is 0.

fpoint 1000-1001 cd.qxd 1/4/02 4:26 PM Page 9

Default

100

110

120

130

140

150

160

170

Network Module

Address (Decimal)

Switch Positions

1-5

180

190

200

210

220

230

240

Not Allowed

123 4 5678

Other Settings

Network Module

Address (Decimal)

Switch Positions

1-5

Network Module

Address (Decimal)

Switch Positions

1-5

fpoint 1000-1001 cd.qxd 1/4/02 4:26 PM Page 10

Autres manuels pour FieldPoint FP-1000

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels National Instruments Équipement d'enregistrement

National Instruments

National Instruments TPC-22 series Manuel utilisateur

National Instruments

National Instruments 9403 Manuel utilisateur

National Instruments

National Instruments FieldPoint FP-1300 Manuel utilisateur

National Instruments

National Instruments DAQ Series Manuel utilisateur

National Instruments

National Instruments VXI-USB Manuel utilisateur

National Instruments

National Instruments USB-8506 Manuel utilisateur

National Instruments

National Instruments FieldPoint FP-1000 Guide de démarrage rapide

National Instruments

National Instruments PCMCIA-232 Manuel utilisateur

National Instruments

National Instruments PXIe-416 Series Manuel utilisateur

National Instruments

National Instruments AT-DIO-32F Manuel utilisateur

National Instruments

National Instruments GPIB-232CT-A IBCL EPROM Manuel utilisateur

National Instruments

National Instruments sbRIO-9601 Manuel utilisateur

National Instruments

National Instruments NI-CAN Manuel utilisateur

National Instruments

National Instruments UMI-7774 Manuel utilisateur

National Instruments

National Instruments PXIe-8240 Manuel utilisateur

National Instruments

National Instruments NI 9860 Manuel utilisateur

National Instruments

National Instruments MXI Manuel utilisateur

National Instruments

National Instruments VXI-AT2023 Manuel utilisateur

National Instruments

National Instruments NI PCIe-8255R Manuel utilisateur

National Instruments

National Instruments GPIB-MAC Manuel utilisateur

National Instruments

National Instruments Cabled PCI Express Manuel utilisateur

National Instruments

National Instruments NI VISION PCI-8254R Manuel utilisateur

National Instruments

National Instruments NI 9403 Manuel utilisateur

National Instruments

National Instruments PCIe-8253 Manuel utilisateur

Manuels Équipement d'enregistrement populaires d'autres marques

KV2 Audio

KV2 Audio 500 Series Manuel utilisateur

Robotics Technologies

Robotics Technologies microBus-Cam II Manuel utilisateur

Seca

Seca 460 Manuel utilisateur

Cognex

Cognex MVS-8000 Series Manuel utilisateur

Mect

Mect MPNC006 Series Manuel utilisateur

Bad Caf

Bad Caf THE LEASH Manuel utilisateur

Strymon

Strymon NIGHTSKY Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur

Tews Technologies

Tews Technologies TPMC465 Manuel utilisateur

Honeywell

Honeywell Excel 50 Manuel utilisateur

SeaLevel

SeaLevel COMM+8.LPCI Manuel utilisateur

Arturia

Arturia AUDIOFUSE STUDIO Manuel utilisateur

Rukra

Rukra RK-1240 Manuel utilisateur

Samson

Samson SCOM Manuel utilisateur

Dynacord

Dynacord DPS260 Manuel utilisateur

Nice

Nice Core Manuel utilisateur

Pyle Pro

Pyle Pro PSS8 Manuel utilisateur

RF-System

RF-System TinyGate Manuel d'utilisation et d'entretien