National Instruments PC-DIO-96 Manuel utilisateur

PC-DIO-96

User Manual

Digital I/O Board for the IBM PC/XT/AT

September 1995 Edition

Part Number 320289B-01

National Instruments Corporate Headquarters

6504 Bridge Point Parkway

Austin, TX 78730-5039

(512) 794-0100

Technical support fax: (800) 328-2203

(512) 794-5678

Branch Offices:

Australia 03 9 879 9422, Austria 0662 45 79 90 0, Belgium 02 757 00 20, Canada (Ontario) 519 622 9310,

Canada (Québec) 514 694 8521, Denmark 45 76 26 00, Finland 90 527 2321, France 1 48 14 24 24,

Germany 089 741 31 30, Hong Kong 2645 3186, Italy 02 48301892, Japan 03 5472 2970, Korea 02 596 7456,

Mexico 95 800 010 0793, Netherlands 0348 433466, Norway 32 84 84 00, Singapore 2265886, Spain 91 640 0085,

Sweden 08 730 49 70, Switzerland 056 200 51 51, Taiwan 02 377 1200, U.K. 01635 523545

Limited Warranty

The PC-DIO-96 is warranted against defects in materials and workmanship for a period of one year from the date of

shipment, as evidenced by receipts or other documentation. National Instruments will, at its option, repair or replace

equipment that proves to be defective during the warranty period. This warranty includes parts and labor.

The media on which you receive National Instruments software are warranted not to fail to execute programming

instructions, due to defects in materials and workmanship, for a period of 90 days from date of shipment, as

evidenced by receipts or other documentation. National Instruments will, at its option, repair or replace software

media that do not execute programming instructions if National Instruments receives notice of such defects during

the warranty period. National Instruments does not warrant that the operation of the software shall be uninterrupted

or error free.

A Return Material Authorization (RMA) number must be obtained from the factory and clearly marked on the

outside of the package before any equipment will be accepted for warranty work. National Instruments will pay the

shipping costs of returning to the owner parts which are covered by warranty.

National Instruments believes that the information in this manual is accurate. The document has been carefully

reviewed for technical accuracy. In the event that technical or typographical errors exist, National Instruments

reserves the right to make changes to subsequent editions of this document without prior notice to holders of this

edition. The reader should consult National Instruments if errors are suspected. In no event shall National

Instruments be liable for any damages arising out of or related to this document or the information contained in it.

EXCEPT AS SPECIFIED HEREIN, NATIONAL INSTRUMENTS MAKES NO WARRANTIES, EXPRESS OR

IMPLIED, AND SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. CUSTOMER'S RIGHT TO RECOVER DAMAGES CAUSED BY FAULT

OR NEGLIGENCE ON THE PART OF NATIONAL INSTRUMENTS SHALL BE LIMITED TO THE AMOUNT

THERETOFORE PAID BY THE CUSTOMER. NATIONAL INSTRUMENTS WILL NOT BE LIABLE FOR

DAMAGES RESULTING FROM LOSS OF DATA, PROFITS, USE OF PRODUCTS, OR INCIDENTAL OR

CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POSSIBILITY THEREOF. This limitation of the

liability of National Instruments will apply regardless of the form of action, whether in contract or tort, including

negligence. Any action against National Instruments must be brought within one year after the cause of action

accrues. National Instruments shall not be liable for any delay in performance due to causes beyond its reasonable

control. The warranty provided herein does not cover damages, defects, malfunctions, or service failures caused by

owner's failure to follow the National Instruments installation, operation, or maintenance instructions; owner's

modification of the product; owner's abuse, misuse, or negligent acts; and power failure or surges, fire, flood,

accident, actions of third parties, or other events outside reasonable control.

Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or

mechanical, including photocopying, recording, storing in an information retrieval system, or translating, in whole or

in part, without the prior written consent of National Instruments Corporation.

Trademarks

LabVIEW®, NI-DAQ®, and GPIB-PCII™are trademarks of National Instruments Corporation.

Product and company names listed are trademarks or trade names of their respective companies.

WARNING REGARDING MEDICAL AND CLINICAL USE

OF NATIONAL INSTRUMENTS PRODUCTS

National Instruments products are not designed with components and testing intended to ensure a level of reliability

suitable for use in treatment and diagnosis of humans. Applications of National Instruments products involving

medical or clinical treatment can create a potential for accidental injury caused by product failure, or by errors on the

part of the user or application designer. Any use or application of National Instruments products for or involving

medical or clinical treatment must be performed by properly trained and qualified medical personnel, and all

traditional medical safeguards, equipment, and procedures that are appropriate in the particular situation to prevent

serious injury or death should always continue to be used when National Instruments products are being used.

National Instruments products are NOT intended to be a substitute for any form of established process, procedure, or

equipment used to monitor or safeguard human health and safety in medical or clinical treatment.

© National Instruments Corporation
vPC-DIO-96 User Manual
Contents
 
Chapter 1
About This Manual............................................................................................................v
Organization of This Manual ........................................................................................v
Conventions Used in This Manual ................................................................................vi
National Instruments Documentation............................................................................vii
Related Documentation .................................................................................................vii
Chapter 1
Introduction..........................................................................................................................1-1
About the PC-DIO-96 ...................................................................................................1-1
What You Need to Get Started......................................................................................1-2
Software Programming Choices....................................................................................1-2
LabVIEW and LabWindows/CVI Application Software..................................1-2
NI-DAQ Driver Software..................................................................................1-3
Register-Level Programming ............................................................................1-4
Optional Equipment ......................................................................................................1-4
Cabling ..............................................................................................................1-4
Unpacking .....................................................................................................................1-5
Chapter 2
Configuration and Installation ..................................................................................... 2-1
Board Configuration......................................................................................................2-1
Base I/O Address Settings.................................................................................2-2
Interrupt Level Selection ...................................................................................2-5
Installation .....................................................................................................................2-5
Signal Connections........................................................................................................2-6
I/O Connector Pin Description ..........................................................................2-7
I/O Connector Signal Connection Descriptions ................................................2-8
Port C Pin Assignments.........................................................................2-8
Cable Assembly Connectors .............................................................................2-9
Digital I/O Signal Connections .........................................................................2-12
Power Connections............................................................................................2-13
Timing Specifications........................................................................................2-14
Mode 1 Input Timing ............................................................................2-15
Mode 1 Output Timing..........................................................................2-16
Mode 2 Bidirectional Timing ................................................................2-17
Chapter 3
Theory of Operation..........................................................................................................3-1
Data Transceivers ..........................................................................................................3-2
PC I/O Channel Control Circuitry.................................................................................3-2
82C55A Programmable Peripheral Interface ................................................................3-2
8253 Programmable Interval Timer ..............................................................................3-2
Interrupt Control Circuitry ............................................................................................3-2
Digital I/O Connector....................................................................................................3-3

Contents

PC-DIO-96 User Manual vi © National Instruments Corporation

Chapter 4

Introduction ...................................................................................................................4-1

Register Map .................................................................................................................4-2

Register Descriptions ....................................................................................................4-3

Interrupt Control Register 1 ..................................................................4-6

Interrupt Control Register 2 ..................................................................4-8

Programming Considerations for the 82C55A..............................................................4-9

Modes of Operation for the 82C55A.................................................................4-9

Mode 0 ...................................................................................................4-9

Mode 1 ...................................................................................................4-9

Mode 2 ...................................................................................................4-10

Single Bit Set/Reset Feature..................................................................4-10

Mode 0—Basic I/O ...........................................................................................4-10

Mode 0 Programming Example ............................................................4-11

Mode 1—Strobed Input.....................................................................................4-12

Mode 1 Input Programming Example ...................................................4-14

Mode 1—Strobed Output ..................................................................................4-15

Mode 1 Output Programming Example ................................................4-16

Mode 2—Bidirectional Bus...............................................................................4-17

Mode 2 Programming Example ............................................................4-19

Interrupt Programming Examples for the 82C55A ...........................................4-19

Programming Considerations for the 8253 ...................................................................4-21

General Information ..........................................................................................4-21

Interrupt Programming Example for the 8253 ..................................................4-22

Interrupt Handling .........................................................................................................4-28

Appendix A

Specifications........................................................................................................................A-1

Appendix B

OKI 82C55A Data Sheet..................................................................................................B-1

Appendix C

AMD 8253 Data Sheet.......................................................................................................C-1

Appendix D

Customer Communication..............................................................................................D-1

Glossary ......................................................................................................................Glossary-1

Index..................................................................................................................................Index-1

Contents

Figures

Figure 1-1. The Relationship between the Programming Environment, NI-DAQ, and Your

Hardware ...........................................................................................................1-3

Figure 2-1. PC-DIO-96 Parts Locator Diagram...................................................................2-2

Figure 2-2. Example Base I/O Address Switch Settings......................................................2-3

Figure 2-3. Interrupt Jumper Setting for IRQ5 (Factory Setting) ........................................2-5

Figure 2-4. Digital I/O Connector Pin Assignments............................................................2-7

Figure 2-5. Cable-Assembly Connector Pinout for Pins 1 through 50 ................................2-10

Figure 2-6. Cable-Assembly Connector Pinout for Pins 51 through 100 ............................2-11

Figure 2-7. Digital I/O Connections.....................................................................................2-13

Figure 3-1. PC-DIO-96 Block Diagram...............................................................................3-1

Figure 4-1. Control Word Formats for the 82C55A ............................................................4-3

Figure 4-2. Control-Word Format for the 8253 ...................................................................4-4

Tables

Table 2-1. PC-DIO-96 Factory-Set Switch and Jumper Settings .......................................2-1

Table 2-2. Switch Settings with Corresponding Base I/O Address

and Base I/O Address Space .............................................................................2-4

Table 2-3. Port C Signal Assignments................................................................................2-9

Table 4-1. PC-DIO-96 Address Map..................................................................................4-2

Table 4-2. Port C Set/Reset Control Words........................................................................4-4

Table 4-3. Mode 0 I/O Configurations ...............................................................................4-11

Table A-1. Maximum Average Transfer Rates for the PC-DIO-96 ....................................A-3

vPC-DIO-96 User Manual

Contents

Chapter 1

About This Manual............................................................................................................v

Organization of This Manual ........................................................................................v

Conventions Used in This Manual ................................................................................vi

National Instruments Documentation............................................................................vii

Related Documentation .................................................................................................vii

Chapter 1

Introduction..........................................................................................................................1-1

About the PC-DIO-96 ...................................................................................................1-1

What You Need to Get Started......................................................................................1-2

Software Programming Choices....................................................................................1-2

LabVIEW and LabWindows/CVI Application Software..................................1-2

NI-DAQ Driver Software..................................................................................1-3

Optional Equipment ......................................................................................................1-4

Cabling ..............................................................................................................1-4

Unpacking .....................................................................................................................1-5

Chapter 2

Configuration and Installation ..................................................................................... 2-1

Board Configuration......................................................................................................2-1

Base I/O Address Settings.................................................................................2-2

Interrupt Level Selection ...................................................................................2-5

Installation .....................................................................................................................2-5

Signal Connections........................................................................................................2-6

I/O Connector Pin Description ..........................................................................2-7

I/O Connector Signal Connection Descriptions ................................................2-8

Port C Pin Assignments.........................................................................2-8

Cable Assembly Connectors .............................................................................2-9

Digital I/O Signal Connections .........................................................................2-12

Power Connections............................................................................................2-13

Timing Specifications........................................................................................2-14

Mode 1 Input Timing ............................................................................2-15

Mode 1 Output Timing..........................................................................2-16

Mode 2 Bidirectional Timing ................................................................2-17

Chapter 3

Theory of Operation..........................................................................................................3-1

Data Transceivers ..........................................................................................................3-2

PC I/O Channel Control Circuitry.................................................................................3-2

82C55A Programmable Peripheral Interface ................................................................3-2

8253 Programmable Interval Timer ..............................................................................3-2

Interrupt Control Circuitry ............................................................................................3-2

Digital I/O Connector....................................................................................................3-3