National Instruments FIELDPOINT FP-1600 Manuel utilisateur

FieldPoint™ and natinst.com™are trademarks of National Instruments Corporation. Product and

company names mentioned herein are trademarks or trade names of their respective companies.

OPERATING INSTRUCTIONS

FP-1600

FieldPoint 10/100 Ethernet

Network Module

These operating instructions describe the installation, features, and

characteristics of the FP-1600. For more detailed information on

using the network module, refer to the FP-1600 user manual.

Features

The FP-1600 is a FieldPoint network module with the following

features:

• Autonegotiating 10/100 Ethernet network interface

• Built-in high efficiency power supply powers I/O modules

• Network watchdog timer

• SnapShot capability and programmable power-up state

• –40 to +55 °C operation

• Connects to an Ethernet network using the TCP/IP protocol

• Supports up to nine I/O modules

• Runs on 11 to 30 VDC power

Kit Contents and Optional Equipment

Your kit contains the following items:

• FP-1600 network module

• Accessories: protective connector cover, two DIN rail stops,

Device Description diskette

You can order the following optional equipment from National

Instruments:

• Panel mount accessory, part number 777609-01

FP-1600 2 www.natinst.com

• Terminal bases and I/O modules, complete list of terminal

bases and I/O modules in the National Instruments online

catalog at www.natinst.com

•Cables

• 24 VDC power supply

Installation

Caution Toavoiddamagingthe FP-1600andthe terminal

bases, make sure that power is not applied to the FP-1600

while you install or remove terminal bases.

Follow these steps to install the FP-1600:

1. Use a flat-bladed screwdriver to open the DIN rail clip to the

unlocked position, as shown in Figure 1.

Figure 1. DIN Rail Clip

Note Write down the serial number from the back of

your FP-1600 before you mount your FP-1600. You will

need this information when you configure the FP-1600.

2. Mount the FP-1600 onto a 35 mm DIN rail or onto a panel

mount accessory.

• Installing onto a DIN rail:

a. Hook the lip on the rear of the FP-1600 onto the top of

a35 mm DIN railand press theFP-1600 downontothe

DIN rail, as shown in Figure 2.

Rail Clip LockedRail Clip Unlocked

Figure 2. Mounting the FP-1600 onto a DIN Rail

b. Slide the FP-1600 to the desired position along the

DIN rail.

c. Lock the FP-1600 to the DIN rail by pushing the rail

clip to the locked position.

• Installing onto a panel mount accessory, which you can

order separately from National Instruments:

a. Snap the panel mount accessory onto the module,

as shown in Figure 3.

Figure 3. Mounting the FP-1600 onto a Panel Mount Accessory

Cover

Press

35 mm DIN Rail

Lip

Local Bus

Connector

Press

FP-1600 4 www.natinst.com

b. Lock the panel mount accessory into place by pushing

the rail clip to the locked position.

c. Mount the FP-1600 and panel mount accessory onto

the desired surface. You can drill pilot holes using the

directions in the FieldPoint Network Module Panel

Mount Accessory installation guide.

3. Add terminal bases with their local bus connectors firmly

mated to the FP-1600 local bus connector.

4. Place the protective cover over the local bus connector of the

last terminal base in the bank. Figure 4 shows an installed

FP-1600 network module on a DIN rail.

Figure 4. Installed Network Module

Network Connection

Connect the FP-1600 to an Ethernet network using the RJ-45

Ethernet port on the FP-1600. Connect the RJ-45 Ethernet port

of the FP-1600 to an Ethernet hub using a standard Category 5

Ethernet cable. You can also connect an FP-1600 directly to a

computer using an Ethernet crossover cable. Do not use a cable

longer than 100 m. Figure 5 shows the power and Ethernet

connectors on the FP-1600.

Protective

Cover

Local Bus Connectors

Firmly Mated

Rail Clip

Locked DIN

Rail

Figure 5. Power and Ethernet Connectors on the FP-1600

Cabling

If you need to build your own cables, the following table shows the

standard ethernet cable wiring connections for both normal and

crossover cables.

Table 1. Ethernet Cable Wiring Connections

Pin Connector 1 Connector 2

(Normal) Connector 2

(Crossover)

1white/orange white/orange white/green

2orange/white orange/white green/white

3white/green white/green white/orange

4blue/white blue/white blue/white

5white/blue white/blue white/blue

6green/white green/white orange/white

7white/brown white/brown white/brown

8brown/white brown/white brown/white

Power Connector

FieldPoint Bank Status Indicators

RJ-45 Ethernet Port

Ethernet Status Indicators

FP-1600 6 www.natinst.com

Figure 6 shows the connector pinouts for FieldPoint Ethernet

cables.

Figure 6. Ethernet Cable

Powering the FP-1600

Caution Connect the FP-1600 to the terminal base before

applying power to the FP-1600 to avoid damaging the

FP-1600 or a terminal base.

Each FP-1600 on your network requires an 11–30 VDC power

supply. The FP-1600 filters and regulates this supplied power and

provides power for all the I/O modules in the bank. Therefore, you

do not need to provide power separately to each FieldPoint I/O

module in the bank. If your field I/O devices need to be powered

separately, you can use the terminals provided on each terminal

base for such power supply connections.

The power connector is a 6-pin screw terminal connector whose

pinout is shown in Figure 7.

Connector 1 Connector 2

pin 1 pin 1 pin 8pin 8

Figure 7. FP-1600 Power Connector Pinout

Connect the primary power supply to the center V and C pair.

You can connect an optional backup power supply to the left V

and C pair. The right V and C pair provides a convenient means

of connecting power to the V and C terminals of a terminal base.

Figure 7 shows this optional connection.

Specifications

Network interface .............................10BaseT and 100BaseTX

Ethernet

Compatibility....................................IEEE 802.3

Communications rate........................10 Mbps, 100 Mbps,

autonegotiated

Cabling distance................................100 m

Power supply range...........................11 to 30 VDC

Power consumption...........................7 W + 1.15 * ∑(I/O module

power requirements)

Maximum terminal bases per bank...9

Maximum number of banks..............determined by network

topology

Operating temperature......................–40 to +55 °C

Storage temperature..........................–55 to +85 °C

Relative humidity..............................5% to 90% non-condensing

Weight...............................................250 g (8.7 oz.)

vvv

ccc

11-30 VDC

Backup Power

Supply

(optional)

–

11-30 VDC

Primary Power

Supply

To adjacent device

(optional connection)

Compliance

Electrical safety ................................designed to meet IEC 1010

EMI emissions/immunity..................CISPR 11

CE Mark Compliance

This product meets applicable EU directive(s) as follows:

EMC directive

Immunity....................................EN 50082–1:1994

Emissions ..................................EN 55011:1991 Group I

Class A at 10 meters

Mechanical Dimensions

Figure 8 shows the mechanical dimensions of the FP-1600.

Dimensions are given in inches [millimeters].

Figure 8. Mechanical Dimensions

4.31

[109.5]

3.60 [91.44]

4.22 [107.19]

Autres manuels pour FIELDPOINT FP-1600

Table des matières

Autres manuels National Instruments Matériel réseau

National Instruments

National Instruments NI ELVIS III Manuel utilisateur

National Instruments

National Instruments Fieldbus Manuel utilisateur

National Instruments

National Instruments DAQ AT-MIO-16X Manuel utilisateur

National Instruments

National Instruments 6023E Manuel utilisateur

National Instruments

National Instruments PXI-1000 Manuel utilisateur

National Instruments

National Instruments NI Vision PXI-1428 Manuel utilisateur

National Instruments

National Instruments NI Vision CVS-1450 Series Manuel utilisateur

National Instruments

National Instruments NI PXI-7831R Manuel utilisateur

National Instruments

National Instruments VXI-1394 Manuel utilisateur

National Instruments

National Instruments GPIB-100 Manuel utilisateur

National Instruments

National Instruments IMAQ PCI-1411 Manuel utilisateur

National Instruments

National Instruments PXIe-5663E Manuel utilisateur

National Instruments

National Instruments FieldPoint cFP-20 Series Manuel utilisateur

National Instruments

National Instruments GPIB Series Manuel utilisateur

National Instruments

National Instruments SCXI-1163 Manuel utilisateur

National Instruments

National Instruments SCB-68 Manuel utilisateur

National Instruments

National Instruments FIELDPOINT FP-1600 Manuel utilisateur

National Instruments

National Instruments NI 9149 Manuel utilisateur

National Instruments

National Instruments PXI PXITM -1000 Manuel utilisateur

National Instruments

National Instruments GPIB GPIB-ENET/100 Manuel utilisateur

National Instruments

National Instruments NI 447 Series Manuel utilisateur

National Instruments

National Instruments NI 653x Manuel utilisateur

National Instruments

National Instruments AT-232/2 Manuel utilisateur

National Instruments

National Instruments SC-2040 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur